Advertisement
What to do if your codec is not listed
If your codec is not in the list, do the following:
•
Start or restart your codec to activate Pairing mode (a codec signals that it
is in Pairing mode for 30 minutes after it is switched on).
•
Alternatively, if you have a codec with a remote control, activate Pairing
mode using the codec menu: Home > Settings > Administrator settings >
Pairing > Activate pairing visibility mode.
If the codec is still not listed, you can enter its IP address manually. Perform
steps i, ii and iii in the
Select codec manually
frame below instead of steps 5
and 6 above.
Select codec manually
i.
Click Select codec manually...
Select codec to pair with
Select codec manually...
IP Settings
ii. Enter the codec IP address or
hostname (a keypad appears
Back
Manual connection
when you tap in the text field).
IP address or hostname
192.168.1.128
iii. Click Start Pairing to start the
pairing process.
Start Pairing
Useful hints
•
Remove the protective foil from the display. You may keep the foil for later
reference.
•
Use the rear mounted folding foot to alter the touch screen tilt.
•
Clean the display using the dry cleaning cloth provided.
•
The power adapter can be fastened under a table top with screws (not
included).
•
Use a cable winder (not included) to keep cables neat and organized. The
winder can be placed under a table top.
Change the IP settings
If you need to use static IP addresses, contact your network administrator to
get the addresses you need for your system.
Select codec to pair with
i.
Click IP Settings.
System name (Codec type)
name@company.com
Select codec manually...
IP Settings
Settings
IP Settings
ii. Select Static IP
assignment.
IP Settings
IP assignment
DHCP
Static
IP address
192.168.1.130
iii. Enter IP address,
Subnet mask
Subnet mask and
255.255.255.0
Gateway (a keypad
Gateway
192.168.1.1
appears when you
tap in the text field).
iv. Click Save to save
the changes, or Exit
to leave without
saving.
B
Connecting the touch screen directly to the codec
The touch screen can be connected directly to the following codecs. The codec
may be part of a Profile system.
•
Codec C40
•
Codec C60
•
Codec C90
Check the system information page on your codec to make sure its software
version is TC4.1 or later. If not, contact your Cisco representative.
1. Switch on Direct connection on the codec. You can use the remote control
(Home > Settings > Administrator settings > Pairing), the web interface
(Advanced Configuration) or the command line interface.
Note:
The codec's first Ethernet connector must be connected to LAN.
The codec is required to reboot for this change to take effect.
2. Connect the touch screen cable to the Power adapter.
3. Connect the shielded Ethernet cable between the Power adapter and the
second Ethernet connector on your codec.
CAUTION:
Do not connect the codec's second Ethernet connector to LAN.
4. Connect the supplied power cable between the Power adapter and the power
socket. Once power is connected, the touch screen start-up procedure begins.
If required, the touch screen downloads and installs new software from the codec.
The touch screen automatically restarts after the software upgrade. This process
may take a few minutes.
Continue when the menu and contact list appear on the touch screen.
Exit
On a Profile system the
codec is placed inside the
foot module.
5 m
1.8 m
Power
Save
adapter
7.5 m
5. Verify that the touch screen is successfully connected to your codec by checking
the codec address displayed in the top banner.
The touch screen is ready to use.
name@company.com
Available
The touch screen
menu and contact list
Codec second
Ethernet connector
Power socket
On our web site you will find an overview of the
worldwide Cisco contacts.
Go to: http://www.cisco.com/web/siteassets/contacts.
Corporate Headquarters
name@company.com
12:00
San Jose, CA 95134 USA
Cisco Systems, Inc.
170 West Tasman Dr.
Advertisement
