Makita HR4003C Instruction Manual
Hide thumbs
Also See for HR4003C:
- Instruction manual (68 pages) ,
- Technical information (19 pages) ,
- Instruction manual (49 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Makita HR4003C
Summary of Contents for Makita HR4003C
- Page 1 INSTRUCTION MANUAL Rotary Hammer HR4003C HR4013C HR5202C HR5212C DOUBLE INSULATION Read before use.
-
Page 2: Specifications
Vibration emission (a ) : 17.0 m/s h,HD ing to EN60745: Uncertainty (K) : 1.5 m/s Model HR4003C, HR4013C Model HR5212C Sound pressure level (L ) : 92 dB (A) Sound power level (L ) : 103 dB (A) Vibration emission (a ) : 7.0 m/s... -
Page 3: Ec Declaration Of Conformity
Designation of Machine: electric shock. Rotary Hammer If operating a power tool in a damp location Model No./ Type: HR4003C, HR4013C, HR5202C, is unavoidable, use a residual current device HR5212C (RCD) protected supply. Use of an RCD reduces Conforms to the following European Directives: the risk of electric shock. - Page 4 Power tool use and care Be sure the bit is secured in place before operation. 18. Do not force the power tool. Use the correct power tool for your application. The correct Under normal operation, the tool is designed to produce vibration. The screws can come rate for which it was designed.
-
Page 5: Functional Description
This switch functions when setting the tool in symbol (lowest speed) to 5 (full speed). symbol modes. Refer to the table below for the relationship between the tions/blows per minute. For Model HR4003C, HR4013C Number on Revolutions per Blows per minute adjusting dial minute... - Page 6 Hammering mode (Switch button Selecting the action mode mode) CAUTION: running. The tool will be damaged. anism, be sure that the change lever is always positively located in one of the action mode positions. Hammer drilling mode 1. Change lever 2. For continuous chipping, scaling or demolition opera- tions, rotate the change lever to the symbol.
-
Page 7: Indicator Lamp
Indicator lamp 1. Side handle 2. Clamp nut The side handle can be swung 360° on the vertical and secured at 2. Service any desired position. It also secures at eight different positions back indicator lamp (red) and forth on the horizontal. Just loosen the clamp nut to swing the side handle to a desired position. -
Page 8: Depth Gauge
Clean the bit shank and apply bit grease before installing the bit. 1. Change lever 2. 1. Bit 2. Release cover Rotate the change lever so that the pointer points to symbol. Then make sure that the bit is securely Insert the bit into the tool. -
Page 9: Operation
Blow-out bulb (optional accessory) NOTE: where the depth gauge strikes against the gear housing/motor housing. OPERATION CAUTION: 1. Blow-out bulb Hammer drilling operation After drilling the hole, use the blow-out bulb to clean the dust out of the hole. Chipping/Scaling/Demolition Set the change lever to the symbol. -
Page 10: Optional Accessories
This tool requires no hourly or daily lubrication because it has a grease-packed lubrication system. It should be relubricated regularly. Send the complete tool to Makita Authorized or Factory Service Center for this lubrication service. To maintain product SAFETY and RELIABILITY, repairs, formed by Makita Authorized Service Centers, always using Makita replacement parts. - Page 12 Jan-Baptist Vinkstraat 2, M a k i t a E u r o p e N . V . 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, M a k i t a C o r p o r a t i o n Anjo, Aichi 446-8502 Japan 885355A228 20170128...