GE B30 Instruction Manual page 626

Port
Ethernet, turn on or off .................................................................. 5-44
failure monitoring ............................................................................ 5-37
HTTP, close .......................................................................................... 5-99
IEC 60870-5-104, close ...............................................................5-101
Modbus, close .................................................................................... 5-50
on rear panel ..................................................................................... 3-12
SNTP, close ........................................................................................5-112
TFTP, close .........................................................................................5-100
USB ......................................................................................................... 4-16
Port number
combinations with protocols ...................................................... 5-50
connectivity report of those used ............................................ 4-76
DNP ......................................................................................................... 5-51
HTTP ....................................................................................................... 5-99
IEC 60870-5-104 ............................................................................5-100
list of ....................................................................................................... 5-44
Modbus ................................................................................................. 5-49
Modbus during installation ......................................................... 3-64
RADIUS .................................................................................................. 5-18
SNTP .....................................................................................................5-112
system log ............................................................................... 5-18, 5-19
TFTP ......................................................................................................5-100
Power metering
specifications ..................................................................................... 2-25
values .................................................................................................... 6-18
Power off, save data first
............................................................... 3-16
Power supply
description .......................................................................................... 3-15
diagram ................................................................................................ 3-12
LED on module .................................................................................. 3-16
removal to replace battery .......................................................10-24
specifications ..................................................................................... 2-27
wire size ................................................................................................ 3-15
Power system settings
...................................................................5-144
Precision Time Protocol
actual values for port state ............................................................ 6-8
clock settings ...................................................................................5-109
error message ...................................................................................... 7-8
port behavior ..................................................................................... 5-45
settings ...............................................................................................5-110
specifications ..................................................................................... 2-30
Preferences
comparing settings ......................................................................... 10-7
Engineer ............................................................................................... 4-76
IEC 61850 ............................................................................................. 5-60
import file ............................................................................................ 10-9
Preserve custom attributes when importing SCD/CID files
10-9
Print front panel labels ........................................................ 4-43, 4-75
Process bus
order codes for compatible URs .................................................. 2-8
overview ............................................................................................... 3-18
Product information
actual values ...................................................................................... 6-26
Device Connectivity Report in Engineer ................................ 4-76
firmware revision ............................................................................. 6-26
Programmed mode
........................................................................... 3-52
x
Protection elements
Protection Summary interface
Protocol selection
............................................................................... 5-50
Prototype firmware error message
PRP
actual values ...................................................................................... 6-11
explained .............................................................................................. 5-46
settings .................................................................................................. 5-44
specifications ..................................................................................... 2-31
PTP
actual values for port state ............................................................6-8
clock settings .................................................................................. 5-109
error message ......................................................................................7-8
port behavior ...................................................................................... 5-45
settings ............................................................................................... 5-110
specifications ..................................................................................... 2-30
pu quantity
.................................................................................................5-4
Pushbuttons
control FlexLogic ........................................................................... 5-169
control logic diagram .................................................................. 5-125
control settings .............................................................................. 5-124
control specifications ..................................................................... 2-23
testing .......................................................................................................7-3
user-programmable FlexLogic ............................................... 5-176
user-programmable logic diagrams .................................... 5-130
user-programmable settings .................................................. 5-126
user-programmable specifications ......................................... 2-24
Q
Quick Connect
........................................................................... 3-67, 3-68
R
RADIUS server
authentication ................................................................................... 5-15
setup .........................................................................................................B-1
RAM required
......................................................................................... 3-54
Reactive power
..................................................................................... 6-18
Reactive power specifications
Real power .............................................................................................. 6-18
Real-time clock
actual values for synchronization ...............................................6-8
settings ............................................................................................... 5-109
Reboot relay
using EnerVista .....................................................................................5-1
.
using relay ..............................................................................................7-3
Recloser curves
...................................................................5-161, 5-199
Redundancy
PRP actual values ............................................................................. 6-11
PRP explained .................................................................................... 5-46
settings .................................................................................................. 5-44
specifications ..................................................................................... 2-31
Relay architecture ........................................................................... 5-166
Relay maintenance ...............................................................................7-3
Relay name
.......................................................................................... 5-141
Release Notes
..................................................................................... 10-14
B30 BUS DIFFERENTIAL SYSTEM – INSTRUCTION MANUAL
.............................................................................5-4
............................ 3-67, 4-4, 5-227
.......................................... 7-11
..................................................... 2-25
INDEX