Displaying Current And Minimum Required Fpd Image Versions - Cisco ASR 1000 Configuration Manual

Chapter 26 Upgrading Field-Programmable Devices
During an automatic upgrade, the Cisco ASR 1000 Series Routers will upgrade as many FPDs as
possible at a time. No user intervention is possible or necessary. The upgrade process will not stop until
all FPD images have been updated.
During manual upgrades, it is important to note that users can only specify upgrades for a single piece
of hardware each time the upgrade hw-module subslot [slot-number/subslot-number] command is
entered. The maximum of three simultaneous upgrades applies to manual upgrades as well. If you
individually specify multiple manual FPD upgrades, only three FPDs can be upgraded simultaneously
and that can only occur when the hardware is in different router slots. The FPD upgrade process will stop
when all FPDs for the specified hardware have been upgraded.

Displaying Current and Minimum Required FPD Image Versions

To display the current version of FPD images on the SPAs installed on your router, use the show
hw-module [slot-number/subslot-number | all] fpd command, where slot-number is the slot number
where the SIP is installed, and subslot-number is the number of the SIP subslot where a target SPA is
located. Entering the all keyword shows information for hardware in all router slots.
The following examples show the output when using this show command.
The output display in this example shows that FPD versions on the SPAs in the system meet the minimum
requirements:
Router# show hw-module all fpd
==== ====================== ====== =============================================
Slot Card Type
==== ====================== ====== ================== =========== ==============
0/0 SPA-5X1GE-V2
---- ---------------------- ------ ------------------ ----------- --------------
0/1 SPA-8X1FE-TX-V2
---- ---------------------- ------ ------------------ ----------- --------------
0/2 SPA-2XCT3/DS0
---- ---------------------- ------ ------------------ ----------- --------------
1/0 SPA-2XOC3-POS
---- ---------------------- ------ ------------------ ----------- --------------
1/1 SPA-8XCHT1/E1
---- ---------------------- ------ ------------------ ----------- --------------
1/2 SPA-2XT3/E3
==== ====================== ====== =============================================
This example shows the output when using the slot-number/subslot-number argument to identify a
particular SPA:
Router# show hw-module subslot 1/0 fpd
==== ====================== ====== =============================================
Slot Card Type
==== ====================== ====== ================== =========== ==============
1/0 SPA-2XOC3-POS
==== ====================== ====== =============================================
OL-14127-08
H/W Field Programmable
Ver. Device: "ID-Name"
1.1 1-GE I/O FPGA
1.1 1-FE I/O FPGA
1.1 1-ROMMON
2-I/O FPGA
3-T3 SUBRATE FPGA
1.0 1-I/O FPGA
1.1 1-ROMMON
2-I/O FPGA
1.0 1-ROMMON
2-I/O FPGA
3-E3 FPGA
4-T3 FPGA
H/W Field Programmable
Ver. Device: "ID-Name"
1.0 1-I/O FPGA
Cisco ASR 1000 Series Aggregation Services Routers SIP and SPA Software Configuration Guide
Optional FPD Procedures
Current Min. Required
Version Version
1.10 1.10
1.1 1.1
2.12 2.12
2.7 2.7
1.4 1.4
3.4 3.4
2.12 2.12
2.7 2.7
2.12 2.12
1.0 1.0
1.4 1.4
1.4 1.4
Current Min. Required
Version Version
3.4 3.4
26-5