Honeywell LYNXR Installation And Setup Gude page 36

✻
83 Enhanced Sequential Mode
Enroll mode
-% 
 DGYDQFH WR QH[W ]RQH WR EH HQUROOHG
]]
 HQWHU QRZ DQG SURFHHG WR 6(5,$/ 180%(5
SURPSW E 

)RU  EXWWRQ NH\V ]RQHV    
 WKH VHULDO QXPEHU ZLOO EH HQUROOHG WR DOO IRXU
-% 0'
EXWWRQV
,I HQUROOLQJ D NH\ WKH SDQHO ZLOO HPLW D ORQJ EHHS
ZKHQ HQWHULQJ D  WR LQGLFDWH WKDW WKH SUHVHQW NH\
VHW XS LV LQYDOLG
1RWHV  $ YDOLG WHPSODWH RU NH\ KDV  H[LVWLQJ
 FRS\ WKH SUHYLRXV VHULDO QXPEHU HQWU\ IURP
WKH EXIIHU
1RWHV  %HIRUH \RX FDQ FRS\ D VHULDO QXPEHU \RX
 YLHZ H[LVWLQJ VHULDO QXPEHU
1RWH
 FRS\ WKH  EXWWRQ NH\ WHPSODWH WKDW KDV EHHQ
VHW LQ ]RQH QXPEHUV  DOO ]RQH SDUD
PHWHUV H[FHSW VHULDO QXPEHUV  2QO\ YDOLG RQ
]RQHV    WKDW GR QRW KDYH
VHULDO QXPEHUV HQUROOHG
1RWHV  7HPSODWH DFFHSWDQFH LV LQGLFDWHG E\ WZR
GHOHWH H[LVWLQJ VHULDO *R WR WKH $ SURPSW
)RU EXWWRQ NH\ ]RQHV    
 KDYH VHULDO QXPEHUV 'HOHWH DOO IRXU
DW RQH WLPH
1RWH
> @ DGYDQFH WR QH[W ]RQH WR EH HQUROOHG
✻
>@ UHWXUQ WR SUHYLRXV SURPSW $
]RQHV HDFK ZLWK D ]RQH W\SH XQLTXH ORRS
QXPEHU
 ,I WKH GLVSOD\ DXWRPDWLFDOO\ DGYDQFHV WR
$ UDWKHU WKDQ E WKH FRQILJXUDWLRQ RI
WKH NH\ LV QRW YDOLG $W WKDW SRLQW FRS\
WHPSODWH VNLS RU UHWXUQ DUH WKH RQO\ OHJDO
HQWULHV
PXVW ILUVW HQWHU D VHULDO QXPEHU ,I QR
VHULDO LV VWRUHG LQ WKH EXIIHU DQG D FRS\ LV
DWWHPSWHG WKH SDQHO ZLOO HPLW D ORQJ EHHS
LQGLFDWLQJ DQ LQYDOLG RSHUDWLRQ
 1RW DSSOLFDEOH IRU  EXWWRQ NH\ ]RQHV 
    
/
2QO\ LI ´ µ LV GLVSOD\HG ,I WKH ´
GLVSOD\HG WKH SDQHO ZLOO HPLW D ORQJ EHHS
EHHSV DIWHU FRS\LQJ
 $ VLQJOH ORQJ EHHS HPLWWHG ZKHQ FRS\LQJ
D LQGLFDWHV WKH WHPSODWH LV QRW YDOLG
/
2QO\ LI ´ µ LV GLVSOD\HG ,I WKH ´
GLVSOD\HG WKH SDQHO ZLOO HPLW D ORQJ EHHS
Note: If "L" is displayed, the serial number for this transmitter has
already been entered, however, it may still be confirmed,
viewed or deleted.
If the transmitter's serial number has not been previously entered, you
may enter the enroll serial number mode (1A) by entering "1", or copy
the last serial number that was entered by entering "2".
If the transmitter's serial number has been previously entered, you may,
view the present serial number by entering "3". If view is selected each
digit will be re-displayed, and the keypad will beep once for digits 1-6,
and three times for the last digit. Once the serial number has been
entered by either selecting a "1" or a "2", you will return to this prompt
with the "L" on the display. The serial number/loop number combination
that was entered can be confirmed by getting two transmissions (fault
and restore) from the RF or UR device or one transmission from the BR
device. If a transmission is received that matches the serial number and
loop number entered, the system will announce the Voice Descriptor for
the loop followed by three beeps, and a "C" will be displayed indicating
that the received serial number and loop number transmission has
been confirmed to match. No further transmissions will be received.
When confirming a 4 button key, only the serial number is confirmed,
since it assumed that all loops are used. Pressing any key will allow a
confirmation.
*Long beep indicates illegal entries, or duplicate serial number/loop
entry*
When the last zone has been entered, the display will remain on that
zone. To exit this mode and return to data field program mode, press 00
at the ZONE NUMBER prompt.
/
µ LV QRW
When all zones have been programmed, test each zone using the
system's Test mode. Do not use the Transmitter ID Sniffer mode for this,
since it will only check for transmission of one zone on a particular
transmitter, and not the zones assigned to each additional loop.
For Zones 26-29, 30-33, 34-37, and 38-41 any loop can be used for RF
enrollment. If enrolling via RF, it will be confirmed without additional
transmissions.
/
µ LV QRW
–36–