Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch OBD 2220 INFO SCAN
Summary of Contents for Bosch OBD 2220 INFO SCAN
- Page 1 OBD 2220 Info Scan en User guide...
- Page 2 | 2 | User guide | OBD 2220 Info Scan Serial No: __________________________________ SW ID: _____________________________________ HW Ver: ____________________________________ Boot Ver: ___________________________________ Prod ID: ____________________________________ Board ID: ___________________________________ Burn Date: _________________________________ Record the above information about your tool. The information is available at Main Menu -->...
-
Page 3: Table Of Contents
OBD 2220 Info Scan | User guide | 3 | en Table of Contents Review Data ..... . 14 Recording ......14 Safety Precautions . - Page 4 | 4 | User guide | OBD 2220 Info Scan 580000 | REV. A | 04.2017 Bosch Automotive Service Solutions Inc.
-
Page 5: Safety Precautions
OBD 2220 Info Scan | User guide | 5 | en Safety Precautions Important Safety Warnings and Instructions For your safety, read this manual thoroughly before operating your scan tool. Always refer to and follow WARNING safety messages and test procedures provided by the manufacturer of the vehicle or equipment being tested. - Page 6 | 6 | User guide | OBD 2220 Info Scan WARNING WARNING Risk of poisoning. Risk of flying particles. • Use this scan tool in locations with • Safety goggles and protective gloves must mechanical ventilation providing at be worn by the operator and any bystand- least 4 air changes per hour.
- Page 7 OBD 2220 Info Scan | User guide | 7 | en WARNING CAUTION Engine compartment contains electrical Risk of equipment or circuit damage. connections and hot or moving parts. • Unless specifically directed by manufac- • Keep yourself, test leads, clothing and...
-
Page 8: Getting Started
| 8 | User guide | OBD 2220 Info Scan Getting Started • A universal OBDII data link connector, called the DLC, with dedicated pin assignments. Introduction • A standard location for the DLC, visible under the The scan tool was developed by experts in the automo- dash on driver’s side. -
Page 9: Obdii Diagnostic Trouble Codes (Dtcs)
OBD 2220 Info Scan | User guide | 9 | en P30xx–P33xx Manufacturer specific Chassis ground P34xx–P39xx Generic (SAE) Signal ground CAN high, J-2284 Chassis Codes K line, ISO 9141-2 & ISO/DIS 14230-4 Code Type Manufacturer reserved C0xxx Generic (SAE) -
Page 10: Specifications
| 1 0 | User guide | OBD 2220 Info Scan LCD display (color, backlit, QVGA resolution) • Indicates additional information is available by scrolling up. key performs the Read Codes function and scrolls back through the screens. Press this key •... -
Page 11: Changing Measurement Units
OBD 2220 Info Scan | User guide | 11 | en Language Setup Diagnostic Menu Language Setup selection allows the user to change the Diagnostic Monitor Tests language used by the Tool. English is the default lan- On-Board Systems guage. -
Page 12: Tool Information
| 1 2 | User guide | OBD 2220 Info Scan • Press • Serial Number (Serial No:) • Software ID (SW ID:) System Setup • Hardware Version (HW Ver:) English/Metric • Boot Version (Boot Ver:) Language Setup •... -
Page 13: Keypad Test
OBD 2220 Info Scan | User guide | 13 | en Display Test • Use the keys until Keypad Test is highlighted. • Press System Setup Check for missing spots in the display English/Metric Language Setup Press BACK to exit... -
Page 14: Program Mode
| 1 4 | User guide | OBD 2220 Info Scan – If FLASH fails, a checksum is shown. Select Review Data. Memory Test • Use the keys until Review Data is INT RAM Passed highlighted. INT FLASH 68ee •... -
Page 15: Code Lookup
OBD 2220 Info Scan | User guide | 15 | en Playback Options Diagnostic Menu Playback Recording Diagnostic Monitor Tests Long PID Names On-Board Systems English/Metric Charging System Monitor Vehicle Information Component Locator Acronyms Review Data Code Lookup System Setup... -
Page 16: Locating Data Link Connector
| 1 6 | User guide | OBD 2220 Info Scan Locating Data Link Connector Select Vehicle • The OBDII data link connector (DLC) is usually AutoID (>=2000) located under the driver’s side dash. Manual (<=1999) • Refer to vehicle user manual for DLC location. -
Page 17: Acronyms
OBD 2220 Info Scan | User guide | 17 | en • Press highlighted. Vehicle? • Press OBDII/EOBD Diagnostic Menu Europe O2 Monitor Tests Asia Diagnostic Monitor Tests Prev: 06 Lancer On-Board Systems Charging System Monitor Vehicle Information Component Locator... -
Page 18: Component Locator
| 1 8 | User guide | OBD 2220 Info Scan Select the component. # Of Emiss Number Of Emission Related DTC • Use the keys until the desired component is highlighted. • Press Component Locator A/T Control Solenoid Valve Asse... -
Page 19: Diagnostic Menu
OBD 2220 Info Scan | User guide | 19 | en Diagnostic Menu I/M Monitors (Emissions) The first time the scan tool links to the vehicle, the The I/M Monitors (Inspection / Maintenance) function is communication protocol is automatically detected, and... -
Page 20: Read Codes
| 2 0 | User guide | OBD 2220 Info Scan Read Codes Some vehicles do not support This Drive Cycle. If vehi- cle supports both types of monitors the I/M Monitors The Read Codes function allows the scan tool to read Menu displays. -
Page 21: Erase Codes
OBD 2220 Info Scan | User guide | 21 | en Indicates that this DTC has turned on the MIL light. • Use the keys until the desired Pending codes are also referred to as choice is highlighted. continuous monitor or maturing codes. -
Page 22: Mil Status
| 2 2 | User guide | OBD 2220 Info Scan Diagnostic Menu • Use the keys until the desired I/M Monitors choice is highlighted. Read Codes Erase Codes MIL Status • Press State OBD Check Select Module View Data... -
Page 23: State Obd Check
OBD 2220 Info Scan | User guide | 23 | en MIL is ON State OBD Check MIL Status Codes Found Monitors OK Monitors Inc Monitors N/A MIL lamp should be ON if engine is running Press ENTER to continue... -
Page 24: Record Data
| 2 4 | User guide | OBD 2220 Info Scan Validating PIDs ABSLT TPS(%) CALC LOAD(%) COOLANT(°C) ENG SPEED(RPM) Validating PID List EQ RATIO11 1.999 FUEL SYS 1 FUEL SYS 2 7/329 IAT(°C) IGN ADV(°) LT FTRM1(%) Please Wait Throttle Position •... -
Page 25: View Freeze Data
OBD 2220 Info Scan | User guide | 25 | en – Operator presses Diagnostic Menu Recording I/M Monitors Read Codes Erase Codes MIL Status State OBD Check View Data Record Data Collecting data for frame #2 View Freeze Data... -
Page 26: Drive Cycle Monitor
| 2 6 | User guide | OBD 2220 Info Scan From Diagnostic Menu: Return to Diagnostic Menu. Select View Freeze Data. • Press • Use the keys until View Freeze Drive Cycle Monitor Data is highlighted. The Drive Cycle Monitor function is very similar to I/M •... -
Page 27: O2 Monitor Tests
OBD 2220 Info Scan | User guide | 27 | en – Since DTCs Cleared shows status of the Return to Diagnostic Menu. monitors since the Diagnostic Trouble Codes were last erased. • Press Since DTCs Cleared 5.10 O2 Monitor Tests... -
Page 28: Diagnostic Monitor Tests
| 2 8 | User guide | OBD 2220 Info Scan 5.11 Diagnostic Monitor Tests Diagnostic Menu The Diagnostic Monitor Test function is useful after Erase Codes servicing or after erasing a vehicle’s memory. Test results MIL Status do not necessarily indicate a faulty component or system. -
Page 29: On-Board Systems
OBD 2220 Info Scan | User guide | 29 | en • Press Select Diag Mon Test O2 Sensor B1S1 5.12 On-Board Systems O2 Sensor B1S2 The On-Board Systems test allows the scan tool to con- Catalyst B1 Purge Flow Mon trol operation of vehicle components, tests or systems. -
Page 30: Charging System Monitor
| 3 0 | User guide | OBD 2220 Info Scan • Press When the cranking condition is detected, the scan tool will begin collecting DLC voltage readings. 5.13 Charging System Monitor The Charging System Monitor function allows the ccan •... -
Page 31: Vehicle Information
OBD 2220 Info Scan | User guide | 31 | en The second “Test Results” screen example did detect that the engine had started, and a KOER reading is • Use the keys until desired selec- displayed. tion is highlighted. -
Page 32: Troubleshooting
| 3 2 | User guide | OBD 2220 Info Scan Troubleshooting IPT (MOD $09) OBDCOND Error Messages IGNCNTR Check the following if an error message displays: CATCOMP1 CATCOND1 • Verify ignition key is in the ON and not in the ACCES- CATCOMP2 SORIES position. -
Page 33: Tool Self-Tests
OBD 2220 Info Scan | User guide | 33 | en Appendix A—PID Definitions • Press Although there are in excess of 300 PIDs, the tool only Tool Self-Tests displays the PIDs the vehicle supports. Tool Self-Tests check the display, keys, and internal PID Description memory. - Page 34 | 3 4 | User guide | OBD 2220 Info Scan PID Description PID Description Charge Air Cooler Temperature Bank ENG SPEED Engine RPM CACT 11, 12 1 Sensor 1 supported, Sensor 2 Engine Oil Temperature supported Exhaust Pressure Sensor Bank 1, Bank...
- Page 35 OBD 2220 Info Scan | User guide | 35 | en PID Description PID Description NOx Sensor Concentration Bank 1 Distance travelled while induce- NOX 12,22 Sensor 2, Bank 2 Sensor 2 ment system active in current 10K SCR_DIST_1N, block 1N (0 - 10000 km), 20K block...
-
Page 36: Appendix B-Glossary
| 3 6 | User guide | OBD 2220 Info Scan Appendix B—Glossary PID Description WG_A_CMD Commanded wastegate A control A/C: WG_A_CMD, B_ Commanded Wastegate A Control, B Air conditioner Control A/D: WG_B_ACT Wastegate B position Analog to digital... - Page 37 OBD 2220 Info Scan | User guide | 37 | en An input signal to the PCM indicating that the brake Connector providing access and/or control of the vehicle pedal is being pressed. This signal is typically used to information, operating conditions, and diagnostic infor- disengage cruise control systems and torque converter mation.
- Page 38 | 3 8 | User guide | OBD 2220 Info Scan EPA: International Organization of Standardization also know Environmental protection agency as International Standards Organization. ESC: KAM: Electronic spark control. An ignition system function that Keep alive memory warns the PCM when knock is detected. The PCM then Knock sensor (KS): retards spark timing to eliminate the knocking condition.
- Page 39 OBD 2220 Info Scan | User guide | 39 | en injectors are mounted in the intake manifold, and fired in When in park or neutral, the PCM operates the engine in groups rather than individually. an idle mode. NOx: PROM: Oxides of nitrogen.
- Page 40 | 4 0 | User guide | OBD 2220 Info Scan injectors for each cylinder. The injectors are mounted in VECI: the intake manifold and are fired individually. Vehicle emission control information. A decal located in Solenoid: the engine compartment containing information about A device consisting of an electrical coil which when the emission control systems found on the vehicle.
-
Page 41: Declaration Of Conformity
OBD 2220 Info Scan | User guide | 41 | en Declaration of Conformity Limited Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGI- NAL RETAIL BUYERS OF BOSCH ELECTRONIC DIAG- NOSTIC TOOLS (“UNITS”) . BOSCH Automotive Service Solutions Units are warranted... - Page 42 ©Bosch Automotive Service Solutions Inc . 1555 Centre Rd Clayton, VIC, 3169 1300 783 031 www .boschdiytools .com .au...