Honeywell VISTA-128BPT Installation And Setup Manual page 92

VISTA-128BPT/128BPT-SIA/250BPT INSTALLATION AND SETUP GUIDE
D
•
Daily Schedule: A partition can have a daily
schedule created. This schedule is generally
used to determine when the system will Auto
Arm and/or Disarm, but it can also be used for
special reporting purposes.
•
Default Screen: On Alpha Keypads, when the
system is disarm the default message is
"Disarmed . . . Ready to Arm". On some
controls, this default screen can be changed
by the installer to say anything up to 32
characters.
•
Direct-Downloading: (*see also download)
Allows the installer to connect directly to the
control panel on site via a laptop without a
phone line.
•
Disarm: To turn the system OFF
•
Download: To send the program data or
commands in the Computer to the control
panel
•
Download ID Number: A user-changeable 8-
digit number that is downloaded to the control
panel on the initial connection, and must
match on any future connection.
•
D.T.M.F.: Abbreviation for Dual Tone Multi-
Frequency, or Touch Tone
•
Dual Reporting: When the same report goes
to two separate central station or receivers
E
•
ECP: Abbreviation for Enhanced Console
Protocol; This is the way that devices such as
addressable keypads, wireless receiver and
relay modules "talk" to the control panel on the
keypad buss.
•
EOLR: Abbreviation for End of Line Resistor
used on Zones
•
EOLSR:
Abbreviation
Supervision Relay used on 4-wire smoke
detector zones.
•
Earth Ground: All control panels provide an
Earth Ground terminal to wire to a ground
post. This ground connection can be used to
ensure protection against lightning hits and
power surges; as a reference point for
supervising telephone lines and zone wiring
ground fault detection
•
Encryption: Encoding; Encryption is used in
the Compass
encode account files. Also used in wireless to
prevent code stealing
•
End of Line Supervision Relay: Relay used to
supervise the
detectors
for End of
Downloading Software
power on 4-wire smoke
•
Event Log: In some controls events can be
stored for later viewing; *Events; Event Log
Types.
•
Events: Situations that have occurred, i.e.
Alarms, Troubles, Arming, Disarming, etc.
•
Event Log Types: The event log stores events
in many categories such as: Alarms, Checks
(troubles),
(Disarm/Arm) System (loss of ac, battery, etc.),
and Test
•
Exit Error Alarm: An alarm caused by leaving
an entry/exit door open after arming.
•
Expansion
additional modules may be used to add zones.
May be a wireless, Multiplex (polling loop), or
Hardwire Zone module.
•
Expansion Zones: Zones that are added to the
system;
Hardwire Zones.
F
•
F.M.: Factory Mutual; Agency listing for
commercial fire controls nation-wide
•
Factory Default: All controls come from the
factory with a set of default values for each
option; these defaults are the most popular
choices for each available options; Factory
defaults can be loaded at anytime by hitting
*97 in the panels program mode.
•
Fixed Word: All Honeywell keypads use
English language displays; some keypads
("alpha") are capable of fully programmable
alpha-numeric description for each zone;
other keypads are non-alpha programmable
but uses Fixed Glass words on the display,
such as Ready, Not ready, Armed, Disarmed,
etc.
•
Forced Bypass: To automatically bypass all
open zones at once.
Line
G
•
Global-Arm/Disarm: In a multi-partitioned
system users that have access to more than
one partition may have the option to
arm/disarm all of their accessible partitions at
the same time.
•
Go/No Go Test: This is a patented test (for
wireless systems) that gives the installer a
definitive Yes or No as to the placement of
wireless transmitters.
to
•
GoTo: In a partitioned system the GoTo
command allows users, with access to more
than 1 partition, to log on and control one
partition from another partition's keypad
•
GUI: Graphic User Interface
10-2
Bypasses, Open/Close
Module: On some
May be wireless, Multiplex,
controls
or