Hints For Optimum Use; Steam Cleaning - Black & Decker FSM1616 Original Instructions Manual

The Delta Head (Fig. D)
This Steam Mop incorporates a built in delta head which
enables you to access into tight corners and narrow gaps.
Caution! Always wear suitable shoes when accessing the
delta head on your steam mop. Do not wear slippers or open
toed footwear.
• Return the handle (4) to the upright position and turn the
steam mop 'OFF'.
• Wait until it cools down (approximately five minutes).
• Place the front of your shoe onto the steam head
removal tab (5b) and press down gently.
• Lift the delta head (5a) up off the steam head (5).
• Fit the delta head cleaning pad (6a) to the bottom of the
delta head.
Filling the water tank (Fig. E)
The water tank on your steam mop is removable for
convenient and easy filling.
Note! Fill the water tank with clean tap water.
Note! In areas of hard water, the use of de-ionised water is
recommended.
• Remove the water tank (3).
• Remove the filter cap by unscrewing in an anti-clockwise
direction.
• Fill the water tank (3) with water.
Warning! Your water tank has a 350ml capacity. Do not over
fill the tank.
• Replace the filter cap by screwing in a clockwise
direction.
• Re-fit the water tank (3).
Note! Ensure the filter cap is firmly secured.
Note! Do not use chemical cleaners with your steam mop
water tank.
Use
Important! This unit will kill 99.9% of bacteria and germs
when used in accordance with the instructions in this manual
and with the micro fibre pad fitted and a continuous run time
of 90 seconds.
Switching on and off
• To switch the appliance on, press the ON/Off button (1).
It takes approximately 15 seconds for the steam mop to
heat up.
• Press the steam operation button (2). This will operate
the pump and the unit will begin to produce steam.
• To stop steam generation, turn the steam operation
button (2) to off. This will maintain power to the boiler for
quicker start up.
• To switch the appliance off, press the ON/Off button (1).
Caution! Never leave the steam mop in one spot on any
(Original instructions)
surface for any period of time. Always place the steam mop
with the handle (4) supported in the upright position when
stationary and make sure the steam mop is turned off when
not in use.
Caution! Always empty the steam mop after use.
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
Variable Steam operation
The unit is equipped with a variable steam operation
controlled by the thumb wheel (10) located on the handle grip
(9). This allows for 3 different surface settings. The variable
steam settings are:
Wood / Laminate
Tile / Vinyl
Stone / Marble

Hints for optimum use

General
Caution: Never use the steam mop without first attaching a
cleaning pad.
• Always vacuum or sweep the floor before using the
steam mop.
• The easiest way to use the appliance is to tilt the handle
to a 45º angle and clean slowly, covering a small area at
a time.
• Do not use chemical cleaners with your steam mop. To
remove stubborn stains from vinyl or linoleum floors, you
can pre-treat with a mild detergent and some water
before using the steam mop.

Steam Cleaning

• Place a cleaning pad (6) on the floor with the velcro 'loop'
side facing up.
• Lightly press the steam mop down onto the cleaning pad
(6).
• Connect the steam mop to the mains.
• Press the ON/OFF button (1). It takes approximately 15
seconds for the steam mop to heat up.
• Press the steam operate button (2). After a few seconds,
steam will start to come out of the steam head.
Note! When first filled or after running dry, it can take up to
45 seconds for steam to be produced.
ENGLISH
5