Page 1: Table Of Contents
Cisco Smart+Connected 7" In-wall Display Reference Guide This document provides additional information about the features of the Cisco Smart+Connected 7" In-wall Display (SCH-7IN-TS-B/W). Refer to the following topics for more information: Overview, page 2 • Package Contents, page 3 •...
Page 2: Overview
The Cisco Smart+Connected 7" In-wall Display is a stylish way to offer total control where the resident needs it most, such as next to the front door, in the kitchen, or in the living room. Since the Cisco In-wall Display supports both Ethernet and Wi-Fi connectivity, it can be securely mounted in any area of the residence to provide consistent and reliable network access.
Page 3: Package Contents
Wireless-N for video intercom. See “Wireless Network Limitations” and “Power and Network Installation Options.” Package Contents Carefully unpack the Cisco In-wall Display and ensure the following items are included in the box. Do not apply excessive pressure to the touchscreen display during handling. Doing so can crack the Caution screen and damage the touchscreen.
Page 4: Back Box Options
Back Box Options Back Box Options The Cisco In-wall Display Back Box is required for installation of a Cisco In-wall Display. It comes in plastic and metal, as a new installation or retrofit installation. The type of Back Box required is dependent on the specific project requirements.
Page 5 Back Box Options Figure 3 Retrofit Back Box Options Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 6: Device Illustrations And Descriptions
Green LED. Lets you know the camera is on. Camera. For video intercom calls. Shortcut buttons (4). For custom programming; to initiate an action or sequence of actions. Use Composer Pro to configure these buttons. Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 7: Touchscreen Placement
57 to 61 inches (145 cm to 155 cm) from the floor (see Figure Consider the camera on the panel and the height of the people in the residence who will use the camera Note for video intercom. Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 8: Led Indicator
IMPORTANT! Before you can complete the instructions below, you must have a Back Box installed Note according to the documentation provided in the Back Box kit. See the “Back Box Options” section on page 4 for details. Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 9 Attach the PoE Injector according to the instructions in your PoE’s installation guide if provided. Step 2 Pull the Ethernet cable from that location to where you want to install the touchscreen. Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 10 The Ethernet is connected directly to the switch (see Figure 8). This power connection requires both neutral and hot connections. Figure 8 Ethernet - Requires a Connection to Ethernet and AC Power Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 11 If a residence requires a large number of Wi-Fi devices, ensure that you have a robust Wi-Fi network (possibly consisting of multiple access points). Figure 9 Wi-Fi - Requires AC Power and WAP Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 12: Power Installation
Cap the ground wire from the wall if you are using a plastic Back Box. Attach the ground wire to the Step 4 Back Box if using a metal Back Box. Figure 10 AC Power Connection Power Box Terminal Block Connect Wires to Terminal Block Back Box Power Cable Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 13 (see Figure 11). Align and carefully slide the power box into the Back Box until the touchscreen is attached to the power Step 5 box. Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 14 Step 7 snap into place easily. (Optional) To secure the touchscreen inside the power box, remove the tape covering the bottom security Step 8 pin before attaching the touchscreen to the power box. Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 15: Configuration
Select each box one at a time and type the address: IP Address, Subnet Mask, Default Gateway, Preferred DNS, and Alternate DNS. When the keyboard appears, type the address, and then press Done. Press OK to return to the Network page. You can now connect to a Director (Cisco Controller) on the Step 9 network.
Page 16: Troubleshooting
System using Composer Pro. Choose the In-Wall 7” Touch Screen V2 driver in Composer Pro and add it to your project. See the Cisco Smart+Connected Residential Installation and Configuration Guide for more information. Troubleshooting Boot Up When the device is booting up, it may take 30 seconds or longer before the Green LED turns on.
Page 17 15). You may need to wiggle the paper clip a bit to get it into the second small hole. Figure 13 Locate the Touchscreen Hole Insert the paper clip through this slot Continue to insert the paper clip through the small hole Bottom of the touchscreen Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 18 Restore to Factory Default Figure 14 Insert the Paper Clip Though the Small Hole Figure 15 Paper Clip Needs to Engage Release Plate Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 19 LED behaves during a factory restore. After a restore, the touchscreen will need to be updated to the same image version of the project (e.g., Step 8 OS 2.2.2 or later). Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 20: Specifications
Authentication: Wi-Fi Protected Setup (WPS), WEP, Wi-Fi Protected Access (WPA), WPA2 Ethernet 10/100 Base-T Ethernet RJ-45 Power Power supply PoE (IEEE 802.3af) AC 100V to 240V, 50 to 60 Hz Power over Ethernet Other Audio G.722 Wideband Audio Environmental Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...
Page 21: Regulatory/Safety Information
Mounting In-wall Regulatory/Safety Information To review regulatory information, go to www.cisco.com/go/smartconnectedresidential/docs. Related Documentation For more information about the Cisco Smart+Connected Residential products, see the following documents and websites: Subject / Document Title Location General Product Information and Home Page www.cisco.com/go/smartconnectedresidential Cisco 1-Year Limited Hardware Warranty Terms www.cisco.com/go/smartconnectedresidential...
Page 22: Warranty
Cisco offers a wide range of support programs to accelerate customer success. These innovative programs are delivered through a unique combination of people, processes, tools, and partners, resulting in high levels of customer satisfaction. For more information, contact your Cisco sales representative or go to www.cisco.com/cisco/web/support/index.html...
Page 23 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.
Page 24 Service and Support Cisco Smart+Connected 7" In-wall Display Reference Guide OL-27263-01...

Cisco SCH-7IN-TS-B/W Reference Manual

Quick Links

Related Manuals for Cisco SCH-7IN-TS-B/W

Summary of Contents for Cisco SCH-7IN-TS-B/W

Table of Contents