Advertisement
Available languages
Available languages
ENGLISH
5. Speed selector
6. Bit holder
Fig. A
7. Battery
8. Charger
9. Charge Indicator
Assembly
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (fig. B)
To fit the battery (7), line it up with the receptacle on the
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (10) while
u
at the same time pulling the battery out of the receptacle.
Fitting and removing a drill bit or screwdriver bit
This tool is fitted with a keyless chuck to allow for an easy
exchange of bits.
Lock the tool by setting the forward/reverse slider (2) to
u
the centre position.
Open the chuck (4) by turning the front part with one hand
u
while holding the rear part with the other.
Insert the bit shaft into the chuck and firmly tighten the
u
chuck.
This tool is supplied with a double-ended screwdriver bit in the
bit holder (6).
To remove the screwdriver bit from the bit holder, lift the bit
u
from the recess.
To store the screwdriver bit, firmly push it into the holder.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Charging the battery (fig. A)
The battery needs to be charged before first use and whenev-
er it fails to produce sufficient power on jobs that were easily
done before. The battery may become warm while charging;
this is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 10 °C or above 40 °C. Recommended charging tem-
perature: approx. 24 °C.
Note: The charger will not charge a battery if the cell
temperature is below approximately 10 °C or above 40 °C.
6
(Original instructions)
The battery should be left in the charger and the charger
will begin to charge automatically when the cell tempera-
ture warms up or cools down.
To charge the battery (7), insert it into the charger (8).
u
The battery will only fit into the charger in one way. Do
not force. Be sure that the battery is fully seated in the
charger.
Plug in the charger and switch on at the mains.
u
The charging indicator (9) will flash green continuously
(slowly).
The charge is complete when the charging indicator (9) lights
green continuously. The charger and the battery can be left
connected indefinitely with the LED illuminated. The LED will
change to flashing green (charging) state as the charger occa-
sionally tops up the battery charge. The charging indicator (9)
will be lit as long as the battery is connected to the plugged-in
charger.
Charge discharged batteries within 1 week. Battery life will
u
be greatly diminished if stored in a discharged state.
Leaving the battery in the charger
The charger and battery pack can be left connected with the
LED glowing indefinitely. The charger will keep the battery
pack fresh and fully charged.
Charger diagnostics
If the charger detects a weak or damaged battery, the
charging indicator (9) will flash red at a fast rate. Proceed as
follows:
Re-insert the battery (7).
u
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
u
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 60 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Selecting the direction of rotation (fig. C)
For drilling and for tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(2) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
Advertisement
