Warnings And Error Messages - Yamaha RACK Reference Manual

Warnings and error messages

Message
Item Already Exists. Replace it? Displayed when you are about to store (overwrite) a Library.
When using Save As, the name of the file you tried to save was the
File Already Exists, Replace it? same name as an existing file.
Displayed when you are about to save (overwrite) data.
Exceed Maximum Number!
The Library exceeds the maximum number of items and cannot be
Library A:XXXX items, Library B:XXXX
loaded.
items
File System is Not Ready. This You tried to start recording immediately after connecting a USB storage
Operation can Overwrite Existing Files device (i.e., while a list was being generated). You tried to change the
or Directories. name of a file or directory.
Over Current Error! This USB Device is The USB device was disconnected because overcurrent was detected in
Not Supported. Please Disconnect. the USB connection.
Tio OUTPUT is in Use by Another TF. The OUTPUT of the Tio1608-D is already in use by a console using
"with OUTPUT" in Quick Config is Quick Config, therefore the "with OUTPUT" in Quick Config was turned
Turned off. off for this console.
An error occurred during the operation. (This is a general error.)
Operation Failed! Less severe than "Unknown".
(Between "Unknown" and "Ignore".)
Invalid Name! Name violates naming convention.
The feature assigned to the knob was not operated. The operation had
no effect.
Operation Ignored. This message refers to Tips operations for User Defined Knobs.
This message is displayed when the feature assigned to a User Defined
Knob cannot be operated.
No data is stored in the Scene you tried to recall, or the data is
SCENE #XX is Empty!
damaged.
SCENE #XX is Read Only! You tried to overwrite a Scene that is write-protected.
Cannot Store! Could not save the data in the Scene memory or in the Library.
Cannot Recall! Could not recall the data from the Scene memory or from the Library.
Operation Failed. Library X Memory You tried to add data when the memory was full.
Full. A or B will be entered into X.
The sample rate setting of the NY64-D is incorrect, therefore it cannot
Wrong Word Clock! (Slot)
sync with the console.
Turn Off 1-knob Mode to Adjust. 1-knob mode is enabled; turn 1-knob mode off.
Nothing to Paste! You tried to paste data when the copy buffer was empty.
Cannot Bookmark This Screen. You tried to bookmark a screen that cannot be bookmarked.
Page Does not Exist.
Cannot Close This Popup.
Not Bookmarked. The item is not bookmarked.
The operation could not be performed because the USB memory was
File Busy! Operation Denied.
being accessed.
Description
- 93 -
Message
Unsupported File Format! You tried to read an unsupported file format from the USB memory.
Storage Not Found! The USB memory could not be recognized.
Couldn't Write File. The file could not be saved to the USB memory.
Could not overwrite the file on the USB memory because the file is
File Protected!
write-protected.
The name of the directory you tried to create matches the name of an
existing directory.
Already Exists!
This message may also be displayed when editing a file or directory
name.
Couldn't Access File. Could not access the file on the USB memory for some reason.
File Error! An internal file access error occurred.
Format Error! An error occurred during formatting.
USB Storage Unmounted! Recorder Recording stopped because the USB memory was removed during
Stopped. recording.
Recording stopped because the USB memory became full during
USB Storage Full! Recorder Stopped.
recording.
Maximum Number of Audio Files
The number of files supported by the USB recorder was exceeded.
Exceeded!
Recording or playback stopped because time is required for a USB
USB Storage Busy: Recorder Stopped!
storage device process.
A USB memory device with an allocation unit size under 4096 bytes
Illegal Storage Format! Format USB
was connected. If you record in this situation, the format may become
Device with the Other USB Port.
damaged.
Low Battery! The backup battery's voltage is low.
Illegal IP Address! The IP address setting or gateway setting is incorrect.
The same rates of the console and the computer that is connected to
USB Sample Rate Mismatch on USB. the USB TO HOST connector are different. (Console: 44.1 kHz, PC; 48
Console:44100Hz kHz)
Set the sample rate of the computer to 44.1 kHz.
The same rates of the console and the computer that is connected to
USB Sample Rate Mismatch on USB. the USB TO HOST connector are different. (Console: 48kHz, PC;
Console:48000Hz 44.1kHz)
Set the sample rate of the computer to 48kHz.
Two or More Devices Have Same Unit Two or more devices connected to the NY64-D via the Dante network
ID! have the same UNIT ID.
Dante Module Error! An error occurred with the Dante module of the NY64-D or Tio1608-D.
The MAC address of the NY64-D is damaged and communication is not
Illegal Dante Module MAC Address!
possible.
Dante Module Memory Error! An memory error occurred with the Dante module of the Tio1608-D.
An excessive amount of audio data was sent over the Dante network
Dante Audio Resource Overflow
connected to the NY64-D.
Reference
Description
TF Series
Reference Manual