Additional Safety Rules; Functional Description; Important Safety - Makita CL072D Instruction Manual

ADDITIONAL SAFETY RULES

1. Read this instruction manual and the charger
instruction manual carefully before use.
2. Do not pick up the following materials:
- Hot materials such as lit cigarettes or spark/
metal dust generated by grinding/cutting metal
- Flammable materials such as gasoline, thinner,
benzine, kerosene or paint
- Explosive materials like nitroglycerin
- Ignitible materials such as Aluminum, zinc,
magnesium, titanium, phosphorus or celluloid
- Wet dirt, water, oil or the like
- Hard pieces with sharp edges, such as wood
chips, metals, stones, glasses, nails, pins or
razors
- Powder to clot such as cement or tonor
- Conductive dust such as metal or carbon
- Fine particle like concrete dust
Such action may cause fire, injury and/or property
damage.
3. Stop operation immediately if you notice anything
abnormal.
4. If you drop or strike the cleaner, check it carefully
for cracks or damage before operation.
5. Do not bring close to stoves or other heat
sources.
6. Do not block the intake hole or vent holes.
SAVE THESE INSTRUCTIONS.

IMPORTANT SAFETY

INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter,
stop operating immediately. It may result in a risk
of overheating, possible burns and even an
explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8
7. Do not incinerate the battery cartridge even if it is
severely damaged or is completely worn out. The
ENB114-2
battery cartridge can explode in a fire.
8. Be careful not to drop or strike battery.
9. Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room
temperature at 10°C - 40°C (50°F - 104°F). Let a hot
battery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
For Model CL072D (Fig. 1)
For Model CL102D (Fig. 2)
• Always switch off the tool before insertion or removal of
the battery cartridge.
• To remove the battery cartridge, withdraw it from the
tool while pressing the buttons on both sides of the
ENC007-6
cartridge.
• To insert the battery cartridge, hold it so that the battery
cartridge front shape fits to that of the battery
installment opening and slip it into place. Always insert
it all the way until it locks in place with a little click. If
not, it may accidentally fall out of the tool, causing
injury to you or someone around you.
• Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
Battery protection system
The cleaner is equipped with the protection system, which
automatically cuts off the output power for its long service
life.
The cleaner stops during operation when the cleaner and/
or battery are placed under the following situation. This is
caused by the activation of protection system and does
not show the cleaner trouble.
• When the cleaner is overloaded:
At this time, release the switch trigger and remove
causes of overload and then pull the switch trigger
again to restart.
• When the remaining battery capacity gets low:
Recharge the battery cartridge.
Switch action (Fig. 3)
To start the cleaner, simply press the "HIGH/LOW" button.
To switch off, press the "OFF" button. To change the
cleaner speed, press the "HIGH/LOW" button. The first