Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Black & Decker 3339-220 3.0 H.P
Summary of Contents for Black & Decker 3339-220 3.0 H.P
- Page 1 154708/3339-220 rtr 5/17/02 2:36 PM Page 1...
- Page 2 154708/3339-220 rtr 5/17/02 2:36 PM Page 2 Black & Decker (U.S.) Inc. • 701 East Joppa Road, Towson, Maryland 21286 Printed in Italy (JUN96-1) Form No. 154708 Copyright © 1996...
-
Page 3: Instruction Manual
154708/3339-220 rtr 5/17/02 2:36 PM Page 3 Instruction Manual 3339-220 3.0 H.P. Plunge Cut Router... -
Page 4: Important Safety Instructions
154708/3339-220 rtr 5/17/02 2:36 PM Page 4 Getting the most out of your tool. IMPORTANT SAFETY INSTRUCTIONS Please take time to read this manual and pay particular attention to the safety rules we’ve provided for your protection. If you have any questions about your Important Safety Instructions tool please call: WARNING: When using electric tools, basic safety precautions should... -
Page 5: Safety Instructions For All Tools
154708/3339-220 rtr 5/17/02 2:36 PM Page 1 Safety Instructions For All Tools • AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is off when plugging in. • KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. •... -
Page 6: Specifications
154708/3339-220 rtr 5/17/02 2:36 PM Page 2 Motor OPERATING INSTRUCTIONS Your B&D tool is powered by a B&D built motor. Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will TURN OFF AND UNPLUG ROUTER cause loss of power and overheating. - Page 7 154708/3339-220 rtr 5/17/02 2:36 PM Page 3 Figure 1 COLLET NUT 1/2" SPINDLE LOCK BUTTON HEIGHT STOP THUMB WHEEL Figure 3 QUICK RELEASE BUTTON Figure 2 Collets PLUNGE RELEASE LEVER NEVER TIGHTEN THE COLLET ON THIS TOOL WITHOUT FIRST INSTALLING A ROUTER BIT IN IT.
- Page 8 154708/3339-220 rtr 5/17/02 2:36 PM Page 4 Plunge Release Lever Figure 4 The plunge release lever allows the router bit to be plunged directly into the workpiece. Simply raise the plunge release lever when you want to lower the router into the work, as shown in Figure 2. You can lower the unit until it reaches your preset stop.
- Page 9 154708/3339-220 rtr 5/17/02 2:36 PM Page 5 If none of the provided screws seems close to the desired height each can be adjusted by loosening the hex nut at the bottom and then turning the screw either in or out to make it the proper length. After adjusting this screw be sure to tighten the hex nut at the bottom.
- Page 10 154708/3339-220 rtr 5/17/02 2:36 PM Page 6 (See Figure 4) You can either turn the thumb wheel or use the handy Figure 8 quick release button discussed above. HAIRLINE 3. Adjust the depth stop bar to the top of its travel by rotating the depth stop control knob shown in Figure 9.
-
Page 11: Operation
154708/3339-220 rtr 5/17/02 2:36 PM Page 7 Figure 10 Figure 11 SHORTEST SCREW Figure 12 TURRET STOP Using the Turret Stop for Sequential Routing Depth 5. Rotate the turret stop so that the shortest screw is directly under the depth stop bar and make your final cut. Settings NOTE: The third screw in the turret stop is provided if your cut is even deep- TURN OFF AND UNPLUG ROUTER. -
Page 12: Direction Of Feed
154708/3339-220 rtr 5/17/02 2:36 PM Page 8 The direction of feed is important in router usage. Be sure the cutter is rotat- ing into the stock by moving left to right on outside edges and clockwise on inside cuts. Switch (Figure 13) TO SWITCH ON THE MACHINE NOTE: Always pull the plug on the cord set out of its receptacle when chang- ing a cutter or fitting the accessories in order to avoid any chance of an acci-... - Page 13 154708/3339-220 rtr 5/17/02 2:36 PM Page 9 NOTES Every B&D tool is of the highest quality. If you wish to contact us regarding this product, please call toll free between 8:00am and 8:00pm ET, seven days a week: 1-800-9-BD TOOL (1-800-923-8665) One Year Free Maintenance All B&D tools for Industry and Construction are covered under a one year...