Specifications; Additional Safety Rules - Makita HP2040 Instruction Manual

ENGLISH
1 Teeth
2 Protrusions
3 Loosen
4 Tighten
5 Side grip
6 Chuck key

SPECIFICATIONS

Model
Max. capacities
Concrete ..........................................High: 20 mm
Steel ................................................High: 8 mm
Wood ...............................................High: 25 mm
-1
No load speed (min ) .........................High: 0 – 2,900
Blows per minute ................................High: 0 – 37,700
Overall length ................................................. 364 mm
Net weight....................................................... 2.3 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Wear a hard hat (safety helmet), safety glasses
and/or face shield. It is also highly recom-
mended that you wear a dust mask, ear protec-
tors and thickly padded gloves.
2. Under normal operation, the tool is designed to
produce vibration. The screws can come loose
easily, causing a breakdown or accident. Check
tightness of screws carefully before operation.
3. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
4. Hold the tool firmly with both hand. Always use
the side grip.
5. Keep hands away from rotating parts.
6. Do not leave the tool running. Operate the tool
only when hand-held
Explanation of general view
7 Sleeve
8 Ring
9 Depth gauge
10 Switch trigger
11 Lock button
12 Reversing switch lever
HP2040
Low: —
Low: 13 mm
Low: 40 mm
Low: 0 – 950
Low: 0 – 12,400
7.
8.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip, bit
or other accessories.
Side grip (auxiliary handle) (Fig. 1)
Always use the side grip to ensure operating safety.
Install the side grip so that the teeth on the grip fit in
between the protrusions on the tool barrel. Then tighten
the grip by turning clockwise at the desired position. It
may be swung 360° so as to be secured at any position.
Installing or removing drill bit
For HP2040 and HP2042 (Fig. 2)
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in
just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return it to the origi-
nal position.
13 Speed change knob
14 Action mode change button
15 Blow-out bulb
16 Vent holes
HP2041
20 mm
—
8 mm
13 mm
25 mm
40 mm
0 – 2,900
0 – 950
0 – 37,700
0 – 12,400
364 mm
2.3 kg
When drilling into walls, floors or wherever
"live" electrical wires may be encountered, DO
NOT TOUCH ANY METAL PARTS OF THE TOOL!
Hold the tool by the insulated grasping surfaces
to prevent electric shock if you drill into a "live"
wire.
Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
HP2042
20 mm
—
8 mm
13 mm
25 mm
40 mm
2,900
950
37,700
12,400
364 mm
2.3 kg
5