Checking The Brake Light Switches; Adjusting The Rear Brake Light Switch; Checking And Lubricating The Cables - Yamaha FJR1300A(D) Service Manual

3. Check:
• Final gear oil filler bolt gasket
Damage → Replace.
4. Install:
• Final gear oil drain bolt
(along with the gasket
Final gear oil drain bolt
23 Nm (2.3 m·kg, 17 ft·lb)
5. Fill:
• Final gear case
(with the specified amount of the recom-
mended final gear oil)
Quantity
0.20 L (0.21 US qt, 0.18 Imp.qt)
Refer to "CHECKING THE FINAL GEAR OIL
LEVEL" on page 3-29.
EAS1MC1046

CHECKING THE BRAKE LIGHT SWITCHES

1. Check:
• Front brake light switch operation
• Rear brake light switch operation
When operating the brake lever and brake
pedal, confirm that the brake light turns on.
Faulty → Refer to "CHECKING THE
SWITCHES" on page 8-169.
EAS21330
ADJUSTING THE REAR BRAKE LIGHT
SWITCH
ECA1MC1033
NOTICE
• If the brake light operation timing is incor-
rect, the cruise control system will not op-
erate correctly.
• If the brake light comes on too early, the
time until the cruise control system is deac-
tivated will be shorter.
• If the brake light comes on too late, the time
until the cruise control system is deactivat-
ed will be longer or the cruise control sys-
tem may not be deactivated.
TIP
• The rear brake light switch is operated by the
movement of the brake pedal.
Adjustment is correct when the brake light
comes on by depressing the brake pedal less
than 10.0–14.0 mm (0.39–0.55 in).
• If the switch is not properly adjusted, ABS fault
code number "23" may be displayed.
New
)
PERIODIC MAINTENANCE
1. Check:
• Rear brake light operation timing
Incorrect → Adjust.
2. Adjust:
• Rear brake light operation timing
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Hold the main body "1" of the rear brake light
switch so that it does not rotate and turn the
adjusting nut "2" in direction "a" or "b" until the
rear brake light comes on at the proper time.
Direction "a"
Brake light comes on sooner.
Direction "b"
Brake light comes on later.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
3. Check:
• Meter display for the rear brake light switch
"ON" → Adjust the brake light switch or check
the brake pedal operation.
▼ ▼▼▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
a. Connect the Yamaha diagnostic tool.
Use the diagnostic code number "82".
Refer to "SELF-DIAGNOSTIC FUNCTION
AND DIAGNOSTIC CODE TABLE" on page
9-5.
b. Check the meter display for the rear brake
light switch.
▲ ▲▲▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
EAS21690
CHECKING AND LUBRICATING THE
CABLES
The following procedure applies to all of the in-
ner and outer cables.
EWA13270
WARNING
Damaged outer cable may cause the cable to
corrode and interfere with its movement. Re-
place damaged outer cable and inner cables
as soon as possible.
3-30
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼ ▼ ▼▼▼ ▼
▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲ ▲ ▲▲▲ ▲
▼▼▼
▲▲▲
▼▼▼
▲▲▲