Download
Share
Print this page
Tripp Lite B126-2X2 Owner's Manual
  1. Manuals
  2. Brands
  3. Tripp Lite Manuals
  4. Matrix Switcher
  5. B126-2X2
  6. Owner's manual
Tripp Lite B126-2X2 Owner's Manual

Tripp Lite B126-2X2 Owner's Manual

Hide thumbs Also See for B126-2X2:

Advertisement

Quick Links

Download this manual See also: Owner's Manual
14-11-047-9333F8.indd 1
Owner's Manual
HDMI Over Cat5
Matrix Switch
Models: B126-2X2, B126-4X4
PROTECT YOUR INVESTMENT!
Register your product for quicker service
You could also win an ISOBAR6ULTRA
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL. 60609 • www.tripplite.com/support
Copyright © 2014 Tripp Lite. All rights reserved.
and ultimate peace of mind.
surge protector-a $50 value!
1
2
2
4
4
7
10
13
15
11/10/2014 3:14:34 PM

Advertisement

loading

Related Manuals for Tripp Lite B126-2X2

Summary of Contents for Tripp Lite B126-2X2

  • Page 1: Table Of Contents

    Register your product for quicker service and ultimate peace of mind. You could also win an ISOBAR6ULTRA surge protector—a $50 value! www.tripplite.com/warranty 1111 W. 35th Street, Chicago, IL. 60609 • www.tripplite.com/support Copyright © 2014 Tripp Lite. All rights reserved. 14-11-047-9333F8.indd 1 11/10/2014 3:14:34 PM...

  • Page 2: Package Contents

    (or a 1080i @ 60Hz signal up to 75 ft. from the transmitter) • Use 24AWG, Solid Wire Cat5e/6 cable, such as Tripp Lite’s N202-Series, to achieve maximum distance and resolution • Further expand the range and number of monitors by adding B126-110 remote repeater units 14-11-047-9333F8.indd 2...
  • Page 3 Product Features • Add up to three repeaters on each channel of the matrix switch, for a total of four displays per channel (an active remote receiver should be the last unit in a channel) • A 1080p @ 60Hz signal can be extended up to 125 ft. for each repeater added into a channel (or up to 175 ft.

  • Page 4: Mounting

    2. 24AWG, Solid Wire Cat5e/6 cable (such as Tripp Lite’s N202-Series) is required to achieve maximum distance and resolution. 3. The diagram below shows a B126-2X2 installation. Installation will be the same for the B126-4X4, except for the number of ports.
  • Page 5 Connect the external power supply to the switch and plug it into a Tripp Lite Surge Protector, Power Distribution Unit (PDU), or Uninterruptible Power Supply (UPS). When receiving power, the following LEDs will illuminate: The Green Power LED, The Orange Source LEDs (for the Source ports that have devices connected to them), and the Green RJ45 Output LEDs.
  • Page 6 Output LEDs, press the button on the remote control of the desired Output port to switch the source being displayed. Note: The same 4 button remote control comes with both the B126-2X2 and B126-4X4. Buttons 3 and 4 will not be used for the B126-2X2.

  • Page 7: Remote Repeater Installation

    2. 24AWG, Solid Wire Cat5e/6 cable (such as Tripp Lite’s N202-Series) is required to achieve maximum distance and resolution. 3. The diagram below shows a B126-2X2 installation. Installation will be the same for the B126-4X4, except for the number of ports.
  • Page 8 Tripp Lite P568-Series High-Speed HDMI cable. Connect the external power supply to the repeater and plug it into a Tripp Lite Surge Protector, PDU or UPS. The Green Power LED and the Green RJ45 LEDs illuminate to indicate the unit is receiving power.
  • Page 9 Output port to switch the source being displayed. Note: The same 4 button remote control comes with both the B126-2X2 and B126-4X4. Buttons 3 and 4 will not be used for the B126-2X2. See the RS-232 Serial Control section in this manual for details on controlling the switch using Terminal Emulation Software.

  • Page 10: Rs-232 Serial Control

    RS-232 Serial Control Before using RS-232 Serial Control, you must first access the Terminal Emulation Software and update the COM port settings. Go to the Setup drop-down menu and select the Serial Port option. Select the COM port that is being used, and update the remaining settings as follows: Baud Rate (57600), Data (8 bit), Parity (none), Stop (1 bit), Flow Control (none).
  • Page 11 RS-232 Serial Control Next, you will need to configure your software to allow input control. Go to the Setup drop-down menu and select the Terminal option. Update the following settings; Receive (LF), Local Echo (enable). The other settings can remain unchanged. 14-11-047-9333F8.indd 11 11/10/2014 3:14:37 PM...
  • Page 12 RS-232 Serial Control Once these settings are updated, the Terminal Emulation Software will recognize the switch, allowing you to enter commands to control the unit. The following table lists the available commands. Command Action sw[x] [n] Switches the source being displayed on the selected output.

  • Page 13: Troubleshooting

    Note: An improper Equalization setting can cause the monitor not to display an image at all. Try each setting until an acceptable image is displayed. What resolution are you trying to reach? Tripp Lite’s HDMI over Cat5 extenders are tested to support up to 1080p @ 60Hz video resolution.
  • Page 14 Do you have any patch panels or other devices in between the transmitter, repeater, and receiver units? Tripp Lite’s HDMI over Cat5 extender products were designed to be connected directly from the transmitter to the repeater and/or receiver via UTP cable.

  • Page 15: Warranty & Product Registration

    Warranty & Product Registration 1-Year Limited Warranty TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its sole option) any such defective products.
  • Page 16 Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

This manual is also suitable for:

B126-4x4