Black & Decker BDH1850SM Instruction Manual page 9

• Press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
• Press the SmartSelect
• Pulling the handle tube back will activate the steam pump. After a few seconds steam
will start to come out of the steam head.
NOTICe:
If the system has been run dry it may take up to 30 seconds to prime the
system on first use.
• It takes a few seconds for steam to enter the cleaning pad. The steam mop will now
glide easily over the surface to be sanitized/cleaned.
• Push and pull the steam mop slowly across the floor to thoroughly steam clean each section.
NOTICe:
During use you may turn off the steam pump by returning the handle to
the upright position, this convenient feature will allow you to place the steam mop on
the resting mat for a short time so that you may move items or furniture, then continue
cleaning without the need to switch the appliance off.
• When you have finished using the steam mop, return the handle tube to the upright
position and turn it 'OFF', place it on the resting mat and wait until the steam mop cools
down. (approximately five minutes)
hAND heLD STeAM CLeANINg - fig O
NOTICe:
To effectively sanitize an area, the lift and reach
head with microfiber pad must be used.
• Remove the hand held steam cleaner (3) from the
steam mop body (10).
• Attach the required accessory.
• Plug hand held steam cleaner electric cord into the outlet.
• Press the ON/OFF button (1). It takes
approximately 15 seconds for the hand held steam
cleaner to heat up.
• Lift the lock off (24) and pull the trigger switch (25)
to activate the steam pump. After a few seconds
steam will start to come out of the accessory.
NOTICe:
During use you may turn off the steam pump by releasing the trigger switch,
this convenient feature will allow you to place the hand held steam cleaner down for a
short time so that you may move items or furniture, then continue cleaning without the
need to switch the appliance off.
• When you have finished using the hand held steam cleaner, release the trigger
switch and turn it 'OFF', wait until the steam cleaner cools down before storing.
(approximately five minutes)
CARPeT RefReShINg
CAUTION:
It is important to monitor the water level in the water tank. To refill the
water tank and continue to sanitize/ clean, return the handle tube (4) to the upright position
and turn the steam mop 'OFF'. Unplug the unit from the wall outlet, and refill the water tank
with supplied water jug.
CAUTION:
Never leave the steam mop in one spot on any surface for any period
of time. Always place the steam mop on the resting mat (7) with the handle tube in the upright
position when stationary and make sure the steam mop is turned off when not in use.
• Place the carpet glider (8) on the floor.
• Lightly press the steam mop down onto the carpet glider until it clicks into place.
• Place the steam mop on the resting mat.
• Plug the steam mop electric cord into the outlet.
• Press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
• Press the SmartSelect
• Pulling the handle tube back will activate the steam pump. After a few seconds steam
will start to come out of the steam head.
• Push and pull the steam mop slowly across the carpet to thoroughly refresh each section.
NOTICe:
During use you may turn off the steam pump by returning the handle tube to the
upright position, this convenient feature will allow you to place the steam mop on the resting
mat so that you may move items of furniture with out the need to switch the appliance off.
• When you have finished using the steam mop, return the handle tube to the upright
position and turn it 'OFF', place it on the resting mat and wait until the steam mop cools
down. (approximately five minutes)
button (2) until the required setting is reached.
TM
button (2) to the Wood/Laminate setting.
TM
O
25
9
1
24