Specifications; Additional Safety Rules - Makita 9560CV Instruction Manual

ENGLISH
1 Wheel cover
2 Screw
3 Lever
4 Bearing box
5 Press

SPECIFICATIONS

Depressed center wheel
diameter/Spindle thread
-1
No load speed (min
Overall length
Net weight
• Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
• Note: Specifications may differ from country to
country.
Power supply
The machine should be connected only to a power
supply of the same voltage as indicated on the
nameplate, and can only be operated on single-phase
AC supply. They are double-insulated in accordance
with European Standard and can, therefore, also be
used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.

ADDITIONAL SAFETY RULES

1. Always use eye and ear protection. Other
personal protective equipment such as dust
mask, gloves, helmet and apron should be
worn when necessary. If in doubt, wear the
protective equipment.
2. Always be sure that the tool is switched off
and unplugged before carrying out any work
on the tool.
3. Keep guards in place.
4. Use only wheels with correct size and wheels
having a maximum operating speed at least as
high as the highest No Load Speed marked on
the tool's nameplate.When using depressed
center wheels, be sure to use only fiberglass-
reinforced wheels.
5. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
6. Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
7. Do not use separate reducing bushings or
adaptors to adapt large hole abrasive wheels.
Explanation of general view
6 Shaft lock
7 Lock nut
8 Depressed center wheel
9 Inner flange
10 Lock nut wrench
100 mm M10
115 mm M14
125 mm M14
)
9560C 9563C
9561C 9564C
9562C 9565C
11,000 11,000
289 mm 299 mm
1.7 kg 1.8 kg
8. Use only flanges specified for this tool.
9. Do not damage the spindle, the flange (espe-
cially the installing surface) or the lock nut.
Damage to these parts could result in wheel
breakage.
10. For tools intended to be fitted with threaded
hole wheel, ensure that the thread in the wheel
is long enough to accept the spindle length.
11. Before using the tool on an actual workpiece,
test run the tool at the highest no load speed
for at least 30 seconds in a safe position. Stop
immediately if there is any vibration or wob-
bling that could indicate poor installation or a
poorly balanced wheel. Check the tool to
determine the cause.
12. Check that the workpiece is properly sup-
ported.
13. Hold the tool firmly.
ENB031-4
14. Keep hands away from rotating parts.
15. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
16. Use the specified surface of the wheel to
perform the grinding.
17. Do not use cutting off wheel for side grinding.
18. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other per-
sons or flammable materials.
19. Pay attention that the wheel continues to
rotate after the tool is switched off.
20. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
21. Position the tool so that the power cord
always stays behind the tool during operation.
22. If working place is extremely hot and humid, or
badly polluted by conductive dust, use a
short-circuit breaker (30 mA) to assure opera-
tor safety.
23. Do not use the tool on any materials contain-
ing asbestos.
24. Do not use water or grinding lubricant.
11 Shaft lock
12 Switch lever
13 Exhaust vent
14 Inhalation vent
15 Speed adjusting dial
9560CV 9563CV
9561CV 9564CV
9562CV 9565CV
2,800 – 11,000 2,800 – 11,000
289 mm 299 mm
1.7 kg 1.8 kg
5