Vcr; Connecting A Vcr - Mitsubishi VS-45609 Owner's Manual

Connecting a VCR

TV back panel
CABLE
ANT-A LOOP-OUT ANT -B
Incoming Cable
VHF/UHF
1
(75 OHMS)
IR EMITTER HOME THEATER
2 3
VCR back panel
2
AUDIO OUT AUDIO IN
IN
L L
Antenna
1
1 2
MONITOR
R R
3
OUT
Figure 1. Connecting VCR with antennas or wall outlet
cable.
Additional connection cables are not
provided with the TV. They should be
available at most electronic stores.
TV back panel
CABLE
ANT-A LOOP-OUT ANT -B
Incoming Cable
VHF/UHF
1
(75 OHMS)
IR EMITTER HOME THEATER
2 4
Cable Box
Rear Terminals
2
OUT IN
3
VCR back panel
3
AUDIO OUT
IN
L
Antenna
1
R
4
OUT
Figure 2. Connecting VCR with cable box.
TV back panel
Y
Cr
CABLE
2
ANT-A LOOP-OUT ANT -B
1
VHF/UHF Cb
(75 OHMS)
Attach
only
one
cable
IR EMITTER HOME THEATER
type
1
IN
White
Antenna 2
Red
VCR back panel
If your VCR has a video
channel or RF ON/OFF
OUT
switch, set to OFF.
Figure 3. Connecting the VCR Audio/Video.
COMPONENT
S-VIDEO
V
TUNER/
I
MONITOR
D
E
Y
O
A
L
L
Cr
U
(MONO)
D
R I
Cb
R
O
DVD
(YCrCb) AUDIO
FIXED/
2
1 VARIABLE
INPUT INPUT OUTPUT
VIDEO OUT
(Y/C)
COMPONENT S-VIDEO
V
TUNER/ I
MONITOR
D
E
Y
O
A
L
L
Cr
U
(MONO)
D
I
Cb R
R
O
DVD
AUDIO
(YCrCb)
FIXED/
2
1 VARIABLE
INPUT INPUT OUTPUT
AUDIO IN VIDEO OUT
L
(Y/C)
1
2
MONITOR
R
S-VIDEO
COMPONENT
V
TUNER/ I
MONITOR
D
E
O
White
A
L
L
U
(MONO)
D
Red
I
R
R
O
DVD
AUDIO
(YCrCb)
FIXED/
2 1 VARIABLE
INPUT INPUT OUTPUT
1
Attach
only
one
VIDEO OUT
AUDIO OUT AUDIO IN
cable
type
L L
(Y/C)
1
1
1 2
MONITOR
R R
Antennas or Wall Outlet Cable
(Figure 1)
Connect the incoming cable to ANT-A on
1
the TV back panel.
Connect two coaxial cables as follows:
One from LOOP-OUT on the TV back panel to
2
ANTENNA IN on the VCR back panel.
One from VCR back panel ANTENNA OUT to
3
ANT-B on the TV back panel.
Now complete figure 3, steps 1-2.
4
Cable Box
(Figure 2)
Connect the incoming cable to ANT-A on
1
the TV back panel.
Connect three coaxial cables as follows:
One from LOOP-OUT on the TV back panel to
2
IN on the back of the cable box.
One from OUT on the back of the cable box to
3
ANTENNA IN on the VCR back panel.
One from ANTENNA OUT on the VCR back
4
panel to ANT-B on the TV back panel.
Now complete figure 3, steps 1-2.
5
Composite Video with Audio or
S-Video with Audio
(Figure 3)
Connect a video cable from VIDEO
1
OUT on the VCR back panel to VIDEO
INPUT-1, or INPUT-2 on the TV back
panel, or INPUT-3 on the TV Front Con-
trol Panel.
If you have an S-VHS VCR, follow the same
steps using the S-Video terminals on the VCR
and TV (in place of the composite terminals).
Connect a set of audio cables from
2
AUDIO OUT on the VCR back panel to
AUDIO INPUT-1, or INPUT-2 on the TV
back panel, or INPUT-3 on the TV Front
Control Panel. The red cable connects
to the R (right) channel and the white
cable connects to the L (left) channel. If
your VCR is mono (non-stereo), connect
only the white (left) cable.
Part II: Installation
17
17