Operation - Makita DLS714 Instruction Manual

SОМurТЧРăаШrФЩТОМО
АůRІIІżŚ It is extremely important to always
sОМurОătСОăаШrФЩТОМОăМШrrОМtХвăаТtСătСОăЩrШЩОră
tвЩОăШПăЯТsО. Failure to do so may result in serious
ЩОrsШЧКlăТЧУurвăКЧНăМКusОăНКЦКРОătШătСОătШШlăКЧН/Шră
the workpiece.
АůRІIІżŚ АСОЧăМuttТЧРăКăаШrФЩТОМОătСКtăТsă
ХШЧРОrătСКЧătСОăsuЩЩШrtăЛКsОăШПătСОăsКаĽăsuЩ-
ЩШrtătСОăОЧtТrОăХОЧРtСăШПătСОăЦКtОrТКХăЛОвШЧНătСОă
suЩЩШrtăЛКsОăКЧНăКtătСОăsКЦОăСОТРСtătШăФООЩătСОă
material level. Proper workpiece support helps to
avoid blade pinch and possible kickback which may
rОsultăТЧăsОrТШusăЩОrsШЧКlăТЧУurв.ăDШăЧШtărОlвăsШlОlвăШЧă
the vertical vise and/or horizontal vise to secure the
workpiece. Thin material tends to sag. Support work-
piece over its entire length to avoid blade pinch and
possible KICKBACK.
►Fig.37: 1. Support
VОrtТМКХăЯТsО
АůRІIІżŚ SОМurОătСОăаШrФЩТОМОăirЦХвăКРКТЧstă
tСОăturЧăЛКsОăКЧНăРuТНОăПОЧМОăаТtСătСОăЯТsОăНurТЧРă
all operations. Otherwise the material may move
during the cutting operation, cause damage to the
blade, and be thrown which may result in loss of
МШЧtrШlăКЧНăsОrТШusăЩОrsШЧКlăТЧУurв.
Install the vertical vise on either the left or right side of
the guide fence or the holder assembly (optional acces-
sory). Insert the vise rod into the hole in the guide fence
or the holder assembly and tighten the lower screw to
secure the vise rod.
►Fig.38: 1. Vise arm
4. Holder 5. Holder assembly
7. Lower screw 8. Upper screw
Position the vise arm according to the thickness and
shape of the workpiece and secure the vise arm by
tightening the upper screw. If the upper screw contacts
the guide fence, install the upper screw on the opposite
side of vise arm. Make sure that no part of the tool
contacts the vise when lowering the handle fully and
pulling or pushing the carriage all the way. If some part
contacts the vise, re-position the vise.
PrОssătСОăаШrФЩТОМОălКtăКРКТЧstătСОăРuТНОăПОЧМОăКЧНătСОă
turn base. Position the workpiece at the desired cutting
ЩШsТtТШЧăКЧНăsОМurОăТtăirЦlвăЛвătТРСtОЧТЧРătСОăЯТsОăФЧШЛ.
Horizontal vise
Optional accessory
АůRІIІżŚ żrТЩătСОăаШrФЩТОМОăШЧХвăаСОЧătСОă
ТЧНТМКtШrăТsăКtătСОătШЩЦШstăЩШsТtТШЧ. Failure to do
sШăЦКвărОsultăТЧăТЧsuПiМТОЧtăsОМurТЧРăШПătСОăаШrФЩТОМО.ă
This may cause the workpiece to be thrown, cause
damage to the blade or cause the loss of control,
аСТМСăЦКвărОsultăТЧăЩОrsШЧКlăТЧУurв.
►Fig.39: 1. Vise knob
shaft 4. Base
The horizontal vise can be installed on the left side of
the base.
18 ENGLISH
2. Turn base
2. Vise rod 3. Guide fence
6. Vise knob
2. Indicator 3. Vise
By turning the vise knob counterclockwise, the screw
is released and the vise shaft can be moved rapidly in
and out. By turning the vise knob clockwise, the screw
remains secured.
To grip the workpiece, turn the vise knob gently clock-
wise until the indicator reaches its topmost position,
then fasten securely. If the vise knob is forced in or
pulled out while being turned clockwise, the indicator
may stop at an angle. In this case, turn the vise knob
back counterclockwise until the screw is released, and
then turn it again gently clockwise.
The maximum capacity of the horizontal vise is 120 mm
width.
HШХНОrsăКЧНăСШХНОrăКssОЦЛХв
Optional accessory
АůRІIІżŚ ůХаКвsăsuЩЩШrtăКăХШЧРăаШrФЩТОМОă
sШăТtăТsăХОЯОХăаТtСătСОătШЩăsurПКМОăШПătСОăturЧăЛКsОă
ПШrăКЧăКММurКtОăМutăКЧНătШăЩrОЯОЧtăНКЧРОrШusăХШssă
ШПătШШХăМШЧtrШХ. Proper workpiece support helps to
avoid blade pinch and possible kickback which may
rОsultăТЧăsОrТШusăЩОrsШЧКlăТЧУurв.
The holders and the holder assembly (optional acces-
sory) can be installed on either side as a convenient
means of supporting workpieces horizontally.
Install them on the side of the tool, then tighten the
sМrОаsăirЦlвătШăsОМurОătСОЦ.
►Fig.40: 1. Holder
When cutting long workpieces, use the holder-rod
assembly (optional accessory). It consists of two holder
assemblies and two rods 12.
►Fig.41: 1. Holder assembly

OPERATION

АůRІIІżŚ MКФОăsurОătСОăЛХКНОăТsăЧШtăМШЧtКМt-
ТЧРătСОăаШrФЩТОМОĽăОtМ.ăЛОПШrОătСОăsаТtМСăТsăturЧОНă
on. Turning the tool on with the blade in contact with
the workpiece may result in kickback and serious
ЩОrsШЧКlăТЧУurв.
АůRІIІżŚ ůПtОrăКăМuttТЧРăШЩОrКtТШЧĽăНШăЧШtă
rКТsОătСОăЛХКНОăuЧtТХăТtăСКsăМШЦОătШăКăМШЦЩХОtОă
stop. The raising of a coasting blade may result in
sОrТШusăЩОrsШЧКlăТЧУurвăКЧНăНКЦКРОătШătСОăаШrФЩТОМО.
АůRІIІżŚ DШăЧШtătШuМСătСОăМХКЦЩăsМrОаsă
аСТМСăsОМurОătСОăsХТНОăЩШХОsăаСТХОătСОăsКаăЛХКНОă
is rotating. Otherwise the tool may lose control and
rОsultăТЧăЩОrsШЧКlăТЧУurв.
2. Holder assembly
2. Rod 12