Tascam DM-3200 Release Notes
Hide thumbs
Also See for DM-3200:
- Owner's manual (120 pages) ,
- Manual (36 pages) ,
- Release notes (26 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tascam DM-3200
Summary of Contents for Tascam DM-3200
- Page 1 » D00992200C DM-3200 DIGITAL MIXER RELEASE NOTES...
-
Page 2: Table Of Contents
V1.30 Remote control ....... 18 User Defined Layer ........3 Switching of BUSS PAN Follows ST PAN during automation is now disabled ... 18 TASCAM FX2.0 support ......4 Slave Lock processing when TASCAM FX Compressor GR meter cascade connection is cancelled ....18 indication .......... -
Page 3: Firmware Update Notice
The transport keys can be locked to protect from pressing them accidentally by pressing SHIFT STOP New Features This section describes the new features for each revision of the DM-3200 software. Version 1.50 User Defined Layer You can monitor the following functionality of the speci- ª... -
Page 4: Tascam Fx2.0 Support
REMOTE Fader Layer. TASCAM FX2.0 support ª The TASCAM FX2.0 provided on the DM-4800 can now be used on the DM-3200 as well. Figure 3 MIDI>SETUP screen The TASCAM FX2.0 multi-effects provide chorus, flanger, de-esser, delay, distortion, compressor, phaser, and pitch shifter, and numerous presets are provided. -
Page 5: Tascam Fx Compressor Gr Meter Indication
Windows Vista ª The settings from this preset bank 3 are recalled into the This version of the DM-3200 is now fully supported by two effect DSP units of the DM3200 for use. Windows Vista 32 bit and Vista 64 bit. -
Page 6: Version 1.30
This allows MIDI devices to be controlled in synchroniza- and when the IF-TD/DM is used in conjunction with the tion with operations on the DM-3200 mixer, or conversely X-48, a maximum of forty channels of digital audio I/O for mixer parameters to be controlled from a MIDI device. -
Page 7: Operation
MIDI port ID destination will not be copied; they will retain their state 00: The DM-3200 ’ s MIDI IN/OUT from before the paste operation. The same applies to 04: USB MIDI 4: PC/CC port... -
Page 8: Automation Wr-Rhs Indication Has Been Added
MMC command type added Cursor location when a multi-control screen is displayed The commands transmitted from the DM-3200 when you perform a JOG operation can now be matched to the device The cursor location will now move to the module selected being controlled. You can choose either Search (46h) or... -
Page 9: Firewire Card Support
ª MIDI control External MIDI devices can be controlled DM-3200 V1.20 allows you to set and edit mixer names so from the DM-3200 using MIDI Control Change and that you can easily differentiate between multiple mixers Program Change Messages using the new external con-... -
Page 10: Remote Operation Through Mmc
DM-3200 Release Notes protocol, so the controlled device may require you to set an NOTE ID of 0 to match the ‘1’ on the DM-3200, for example. The You can cancel the entered name by pressing the POD3 key (CANCEL). -
Page 11: Midi Controllers
MIDI control has 16 channels. : If the device is a MIDI controller, indicates the MIDI channel of the device being controlled by the DM-3200. If the device is a displays the number of the MIDI fader MIDI Control Change message (0 - 119). -
Page 12: Midi Mixer
FADER right on the MIDI MIXER screen, and press the ENTER key. MUTE key of the DM-3200. In the default setting, they Use the knob to select the key whose assigned func- control FADER , and MUTE respectively. -
Page 13: Cascade Connection
ON/OFF Master/slave setting key. A confirmation screen will come up. Check ENTER You need to set one DM-3200 to be the cascade master and the setting and press the ENTER key again to confirm. the other to be the cascade slave. Any set-up that affects... -
Page 14: Gpi Functionality
If a cascade connection was not properly established, devices from the DM-3200. a pop-up message “Cascade Slave not found. Cascade The DM-3200 allows you to give different trigger settings connection not established” will be displayed. to each of the GPI ports for GPI signal output. You can... - Page 15 ”When the fader stops” means when the fader level is cell in the TYPE column that you want to edit, then use the brought down to the lowest level. JOG/DATA dial to select the type. The Output pulse range is approximately 150ms. TASCAM DM-3200 Release Notes...
-
Page 16: Expanded Dynamic Automation Function
Image parameter of the linked channel (please see “Pan Initial Status. and balance settings” on page 71 of the DM-3200 Owner’s Manual). Settings prohibited to change during automa- tion re-play •... -
Page 17: Version 1.10
Press Control + Library Store together to operate this shortcut. Maintenance Items This section describes the Maintenance items for each revision of the DM-3200 software. Version 1.60 Option Slot Cards A problem where Timecode Locations were incorrectly •... -
Page 18: Version 1.50
External Controller that used the appear. remote fader bank, moving the master fader would operate Popup message: the Mackie Control master fader function even when the fader bank was currently assigned to the other controller. This has been fixed. TASCAM DM-3200 Release Notes... -
Page 19: Store Button In The Library/Automation Lcd Screen
When using the Keep function data have been addressed • Known Issues This section describes the Known Issues for the latest DM-3200 software Version 1.60 DTRS REC FUNCTION setting when con- mode or Hibernation mode, please re-launch TMC or your ª... - Page 20 » DM-3200...