Toshiba Strata DK 280 Installation Manual page 394

Program 72-Dialed Number Identification
Service (DNIS) Number Network Table
Assignments
This program defines the external Network routing
numbers that can be assigned DNIS/tie/DID extension
numbers in the Day, Day2, or Night ringing mode. This
assignment will cause incoming DNIS/tie/DID calls to
route (forward) back out over a public, or private,
telephone network to a pre-assigned telephone
number.
Each of the DK280 RCTU, Release 3, processors
support a different quantity of DNIS Network numbers
as follows: RCTUC3/D3 - 300 DNIS Network routing
numbers; RCTUBA3/BB3 - 200 DNIS network routing
numbers; and RCTUAB - 100 DNIS Network routing
numbers.
To assign a tie/DID line to Program 72 assignments:
The DNIS/tie/DID extension number must be assigned
to route to the appropriate Network routing number in
Program 71-1 (#300 - #599).
This program can also be used with non-DNIS or ANI
(only), tie and/or DID Lines to assign normal incoming
tie/DID calls to route back out over the public, or
private telephone network to an external telephone
number.
1.
2.
3.
IMPORTANT!
Tie/DID lines used for DNIS network
routing must be enabled with tandem
(two-CO-line) connection with Program
15, Code 5.
DNIS Network routing numbers will not be
restricted by DK280 Toll Restriction
assignments.
Tie/DID lines must have LED05 ON in
Program 17 to use the DNIS routing
assignments in Program 71 and 72.
Program 74-System NT Button Lock Password
DK280 system provides three system ringing modes
(Day/Day2/Night). The system ringing modes are
controlled by the NT button which is programmed on
'a telephone or attendant console flexible button
(Program 39). Each ringing mode allows incoming
calls to be routed to different destinations. An NT Lock
button can be assigned (Program 39) to lock the
system into a ringing mode. To lock the system ringing
mode requires a password. The password for each
NT(I - 4) button is assigned in this program.
Attendant consoles and stations (assigned in Program
*36) can also change the NT Lock button Password
using a special access code. One pa-ssword is
provided for each of the four Tenant Line group NT
buttons.
1.
2.
IMPORTANT!
To lock a system into ringing mode
requires two buttons on
the
telephone/attendant console, the NT
button and the NT Lock button. These
buttons can appear on any telephone(s)
or attendant
console(s). The NT button
switches the (Tenant/system) lines into
the desired ringing mode and the NT
Lock
(used in with the Night Lock
password) button locks the NT button into
that ringing mode.
Programs related to Program 74 are:
Program 39-NT Buttons and NT Lock
Buttons; Program
*36-system
ring
mode locking password change station
assignment; Program *15-CO line
Tenant assignments; and Program 77-3-
Tenant Night ring over selected External
Page Zones.
Program 76-1 (X-Y)-RSIU/RSIS/RMDS Port
Assignments
Assigns each installed RSIU port to a function. Where
X identifies the RSIU/RSIS/ RMDS Port No.1 - 4 and
Y identifies the RSIU port function as shown below:
Y=l, TTY or RMDS modem (see Note 4 on next
page-Program 77-1, LED 14).
Y=2, SMDR
Y=3, MIS or SMIS
Y=4,
SMDI
Y=5, Open Architecture
Y=O, No function - this should be used for any of
the four RSIU/RSIS/RMDS ports that are not
used.
Notes:
1. Function codes set in Program 76- 1 X-Y
will override RSSU, PIOU, and/or PlOUS
function codes (4 1, 42, 43) set in Program
03.
I
9-34
January 1996