Toshiba Strata CIX Programming Manual page 62

Telephone Button Programming
300 Series Programs
Table 1-28 Programs 303~315 (continued)
Button Sequence
304-19 Intercept
FB19 Hold
, n,
304-20 Send Dial Tone
FB20 Hold
, n,
304-21 TGAC Override
FB21 Hold
, n,
304-22 Network COS
FB22 Hold
, n,
304-23 LCR Group
FB23 Hold
, n,
304-24 Change COS
Override Code
FB24 Hold
, n,
304-25 Register Speed Dial
Codes
FB25 Hold
, n,
304-26 Originator Invoke
OCA
FB26 Hold
, n,
304-27 Senderized Tone
Mode
FB27 Hold
, n,
304-28 Emergency Call
Group
FB27 Hold
, n,
304-29 Tenant Number
FB29 Hold
, n,
305 ILG Delete
305 Hold
,
305-00 ILG Number
Hold Hold
n, ,
306 Outgoing Line Group
Assignment
306 Hold
,
306-00 Group Number
Hold
n,
306-01 Group Type
FB01 Hold
, n,
306-02 Trunk Type
FB02 Hold
, n,
1-58
Value(s)
n = 1. Enable
2. Disable (default)
n = 1. Enable
2. Disable (default)
n = 1. Enable
2. Disable (default)
n = 1~32
(default = 1)
n = 1~16
(default = 1)
n = 1. Enable
2. Disable (default)
n = 1. Enable
2. Disable (default)
n = 1. Enable
2. Disable (default)
n = 1. Dial Tone (default)
2. Entry Tone
3. Silence
n = 1~8
(default = 1)
Hold
,
n = 1~8 (default = 1)
Hold
,
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n = 1. Analog (default)
2. ISDN
n = 1. CO (default)
2. Tie
Summary
Enable Intercept. A call is transferred to a special destination called
intercept position when the destination of a trunk line call is not
determined with DID, DIT or DISA. Intercept is also activated when
the destination is determined, but the call cannot be terminated due to
a defect or an incorrect number. If the system has a simplified
attendant console, the attendant console is usually specified to
terminate the call. This function ensures termination of a trunk line
call.
Enable Send Dial Tone.
Enable Trunk Group Access Code (TGAC) override.
Enter the Network COS number.
Enter the LCR Group number. Calls from this ILG cannot tandem if
this field is not entered.
Enable authority to change COS Override Code.
Enable authority to create system speed dial codes.
Enable authority for the originator of a call to invoke OCA when
encountering a busy station.
Send DTMF tones as a complete number rather than digit-by digit.
Used to enable E911 calling across a QSIG network. The QSIG ILG
is assigned to an Emergency Call Group in the same way a station is
in Program 200 FB17. Without this assignment, the call will not
attempt to complete to one of the trunks in the Emergency Group and
will result in an abandoned call. See Program 550
Emergency Call Groupî on page
Enter the Tenant number to which this DID should be assigned.
This command deletes Incoming Line Groups.
Enter the ILG number to delete.
OLG is a line selection feature which enables the use of external trunk
or private line groups for outgoing service. Assign and configure up to
128 OLGs (the same line can be placed in an OLG and an ILG).
Enter the OLG Group number.
Select the OLG Type.
Select the Trunk Type.
Strata CIX/CTX Telephone Button Programming 11/04
ìEnhanced 911
1-87.