Netum NT-1228BL Quick Setup Manual
Hide thumbs
Also See for NT-1228BL:
- Quick setup manual (14 pages) ,
- Setup manual (36 pages) ,
- Manual (70 pages)
Related Manuals for Netum NT-1228BL
Summary of Contents for Netum NT-1228BL
- Page 1 · Bluetooth Connection · 2.4Ghz Wireless Connetion . USB Wired Connection Package Included: 1 X Scanner; 1 X USB Receiver; 1 X USB Cable; 1 X Quick Setup Guide...
- Page 2 Quick Setup Guide. 2.4 GHz Wireless USB2.0 Wired Important Note: This is a general manual. It applies to model W8-X and W6-X Please pay attention to the title when you are using the command barcodes. How to Start There are three kinds of connection modes: ·USB Wired ·2.4GHz Wireless Connection ·Bluetooth Connection...
- Page 3 2.Working via 2.4GHz USB Receiver (By default) .Scan " RF 2.4GHz Transmission". ① .Plug the USB receiver on your device. ② .Set Keyboard language→See page (5) . ③ .Locate cursor on the place where you want scanner to output the ④...
-
Page 4: Bluetooth Connection Modes
2. Touch Home | Menu | Settings | Wireless & Networks | Bluetooth settings 3. Make sure the device has Bluetooth “On”. 4. In the list of found devices, select “Netum Bluetooth”. Tap Pair. 5. The scanner will make one long beep after bluetooth paired and LED light will... - Page 5 IOS: Tap Settings | General| Bluetooth. Turn on. A Bluetooth device search will begin. 3. In the device list, tap on “Netum Bluetooth”. Tap Pair. 4. The scanner will make one beep once it’s connected and LED light will turn to solid blue (no blinking) and is ready to scan.
-
Page 6: Barcode Programming
USB COM (Virtual Serial Port) Barcode Programming Netum barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide. An asterisk (*) next to an option indicates the default setting. -
Page 7: Keyboard Language
Keyboard Language For example: If you use French Keyboard, scan barcode of “ French Keyboard”. Locate the cursor on the place where you want to output the data then you can start to scan. American Keyboard is set by default, if you use a US keyboard you can just ignore it. -
Page 8: Working Mode
Working Mode (Apply for 2.4GHz and Bluetooth Connection) Normal Mode: Data will be uploaded after each scan at real time. *Normal Mode Store Mode: All scanned data will be stored directly into the memory of the device. Store Mode Output Stored Data:All data entries in the buffer memory will be manually uploaded after reconnecting to the working station. -
Page 9: Beep Settings
Beep Settings Beep Off: Disable scanner from beeping to indicate successful scans. $BUZZ#0 Beep OFF Beep On: Enable scanner to beep to indicate successful scans. $BUZZ#1 *Beep On Terminator The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by scanning the appropriate barcode below. -
Page 10: Charge The Battery
$POWER#OFF $RF#ST00 Power Off Disabled Idle $RF#ST02 $RF#ST06 *1 Mins 3Mins $RF#ST20 $RF#ST60 10Mins 30Mins Charge the battery When scanner makes 2 beeps or battery volume under 20% please plug USB cable into scanner and connect the other side with your device to charge power for it. By scanning below barcode you can get the remaining battery volume. -
Page 11: Firmware Version
Firmware Version: Read below command barcode to check scanner’s firmware version. $SW#VER Note: Please always provide scanner’s firmware version for reference when you turn to service team for help. Problem: Some barcodes cannot be read. Solution: a. Dirty or unclear barcodes might not be read. b. -
Page 12: Contact Information
Problem: Bluetooth can not be paired. Solution: Scan “AT+MOBE=2”and re-paired it again Problem: Got a W8-X 2D scanner but it can not read datamatrix GS1. Solution: Please contact us to get the command barcode to enable the scanner output Datamatrix GS1. Problem: Got W6-X 1D scanner but it can not read EAN/UPC with 2 or 5 supplements.