Table of Contents
Advertisement
OPERATION
00.00.46.22: TCP 010.232.053.025 on port 6001 Disconnected
00.00.46.22: Route Drop 7.123.123.123.12.03
00.00.46.22: TCP 010.232.053.025 on port 6002 Disconnected
00.00.47.34: Route Drop 2.123.12.3401
00.00.47.34: Route Drop 2.123.12.3402
00.00.47.34: Route Drop 2.123.12.3403
00.01.53.10: BREAK command received
00.00.00.00: Wayside Access Gateway Started
00.00.00.03: Route Add XPORT 10.232.53.41 7.620.123.123.12.10
00.00.00.16: XPORT IP Address: 010.232.053.040
00.00.00.16: CONFIG command received
00.01.28.13: Diagnostic verbosity changed from 1 to 10
00.01.28.55: Route Add Serial 7.777.777.777.77.77
00.01.30.15: Route Add Echelon 001.003 type 41 7.620.020.010.03.02
00.01.30.23: Route Add XPORT 10.232.53.41 7.620.020.020.03.02
00.01.30.23: Route Add XPORT 10.232.53.41 7.620.020.020.03.03
00.01.30.34: Diagnostic verbosity changed from 10 to 10
00.01.30.40: Diagnostic verbosity changed from 10 to 9
00.01.30.54: Route Drop 7.777.777.777.77.77
00.01.31.17: Route Add Serial 7.777.777.777.77.77
00.01.33.37: Route Drop 7.777.777.777.77.77
00.01.35.07: CRASH: 0x0003 st 21E5 ad 00000001 ins 21FC
00.01.35.07: st 2000 bad 00232B2C ret 00232C7C
00.01.35.07: D0: 00200000
00.01.35.07: D1: 00200001
00.01.35.07: D2: 00200002
00.01.35.07: D3: 00200003
00.01.35.07: D4: 00200004
00.01.35.07: D5: 00200005
00.01.35.07: D6: 00200006
00.01.35.07: D7: 00200007
00.00.00.00: Wayside Access Gateway Started
00.00.00.00: Route Add Echelon 001.003 type 41 7.620.020.010.03.02
00.00.00.00: Route Add XPORT 10.232.53.41 7.620.020.020.03.02
00.00.00.01: Route Add XPORT 10.232.53.41 7.620.020.020.03.03
00.00.00.16: XPORT IP Address: 010.232.053.040
00.00.00.47: Route Add XPORT 10.232.53.41 7.620.123.123.12.10
00.00.12.53: Diagnostic verbosity changed from 1 to 11
00.00.13.07: Diagnostic verbosity changed from 11 to 10
00.00.13.17: Diagnostic verbosity changed from 10 to 2
00.01.03.42: WARNING: Received XPORT slipped
3.20 LOG ENTRIES
Log entries are divided into three levels:
•
Fatal messages are used by Siemens Rail Automation personnel to diagnose system errors.
If a fatal problem occurs and gets logged, the WAG will restart itself.
Warnings are used by Siemens Rail Automation personnel to diagnose system errors or an
•
unexpected problem. If a warning occurs, the software continues to operate. The WAG
continues normally after the warning is logged.
•
Informational messages inform the user about normal expected WAG operations.
The log entries are described in table 3-2.
Document No.: COM-00-05-16
Version: C.1
A0: 00100000
A1: 00100001
A2: 00100002
A3: 00100003
A4: 00100004
A5: 00100005
A6: 00100006
A7: 000575DE
3-18
June 2006, Revised June 2014
Advertisement
Table of Contents
Troubleshooting
