Brother DCP-8110DN Service Manual page 151

Location of screw
*1
Earth plate
Joint cover
USB host PCB ASSY
NCU unit
NCU shield cover
NCU PCB ASSY
Main PCB ASSY
Fuser unit line cover R
Fuser unit line cover L
Fuser unit
Laser unit
Scanner earth plate
LV shield plate cover
Inlet
Earth harness
Low-voltage power supply PCB
ASSY
Under bar earth plate R
Under bar
(Front right side)
LV shield plate
Hold cover 1
Toner LED PCB ASSY
Hold cover 2
Under bar earth plate L
Under bar
(Front left side)
Under bar (Rear side
(DCP-8250DN/MFC-8950DW/
8950DWT/8952DW/8952DWT
only)
Main frame L ASSY
Drive sub ASSY
Screw type
Taptite cup S M3x8 SR
Taptite bind B M4x12
(Non touch panel only)
Taptite bind B M4x12
Taptite bind B M4x12
Taptite bind B M4x12
Screw pan (S/P washer)
3.5x6 DA
Taptite cup S M3x6 SR
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite pan B M4x14
Taptite pan B M4x14
Taptite cup S M3x8 SR
Taptite cup S M3x8 SR
(Fastening side of
scanner plate )
Taptite cup S M3x8 SR
(LV shield plate side)
Taptite cup S M3x8 SR
Taptite bind B M4x12
Screw pan M4x8
Taptite flat B M3x10
Screw pan M4x8
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite bind B M4x12
Taptite bind B M4x12
Taptite pan B M3x8
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite bind B M4x12
Taptite cup S M3x8 SR
Taptite bind B M4x12
Taptite bind B M4x12
3-5
Tightening torque
Q'ty
N.m (kgf.cm)
1 0.7±0.1(7±1)
1 0.8±0.1(8±1)
4 0.8±0.1(8±1)
2 0.8±0.1(8±1)
2 0.8±0.1(8±1)
1 0.45±0.05(4.5±0.5)
2 0.45±0.05(4.5±0.5)
6 0.5±0.1(5±1)
1 0.8±0.1(8±1)
1 0.8±0.1(8±1)
1 0.8±0.1(8±1)
4 0.8±0.05(8±0.5)
1 0.8±0.1(8±1)
1 0.5±0.1(5±1)
3 0.5±0.1(5±1)
1 0.8±0.1(8±1)
1 0.5±0.1(5±1)
1 0.5±0.1(5±1)
1 0.5±0.1(5±1)
1 0.5±0.1(5±1)
2 0.8±0.1(8±1)
1 0.5±0.1(5±1)
1 0.8±0.1(8±1)
1 0.8±0.1(8±1)
1 0.8±0.1(8±1)
1 0.5±0.1(5±1)
2 0.8±0.1(8±1)
1
0.8±0.1(8±1)
1
2 0.8±0.1(8±1)
3 0.8±0.1(8±1)
4 0.8±0.1(8±1)
8 0.8±0.1(8±1)
Confidential