Table of Contents
Advertisement
10.1 Setting the cooking time
You can set the cooking time for the operation up to
24 hours.
Requirement: An operating mode and temperature or
level have been set.
Press
"Cooking time".
1.
To set the cooking time, press the relevant time
2.
value, e.g. hour display "h" or minute display "m".
a The selected value is marked in blue.
Use the setting ring to set the cooking time.
3.
If required, use
to reset the setting value.
To confirm the set cooking time, press
4.
play.
Press
to start the operation.
5.
a The appliance starts to heat and the time counts
down.
a When the time has elapsed, a signal sounds. A
message appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
6.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing the cooking time
You can change the cooking time at any time.
Press
on the display.
1.
Press the cooking time
2.
Use the setting ring to change the cooking time.
3.
To confirm the change, press
4.
a The change is applied.
Cancelling the cooking time
You can cancel the cooking time at any time.
Press
on the display.
1.
Press the cooking time
2.
3.
Reset the cooking time using
Note: For operating modes that always require a
cooking time, the appliance resets the cooking time
to the preset value.
To confirm the change, press
4.
a The change is applied.
10.2 Setting the end time
You can delay the time at which the cooking time for
the operation is due to end by up to 24 hours.
Notes
¡ To achieve good cooking results, do not delay the
time once the operation has already started.
¡ Food will spoil if you leave it in the cooking com-
partment for too long.
Requirements
¡ An operating mode and temperature or level have
been set.
¡ A cooking time is set.
Press
"End time".
1.
To set the time, press the hour display or the minute
2.
display.
a The selected value is marked in blue.
Use the setting ring to delay the time.
3.
If required, use
to reset the setting value.
4.
To confirm the set time, press
on the dis-
to switch the ap-
.
on the display.
.
.
on the display.
on the display.
Press
to start the operation.
5.
a The display shows the time remaining until the oper-
ation starts. The appliance is in standby mode.
a Once the start time has been reached, the appli-
ance starts heating and the cooking time starts
counting down.
a When the time has elapsed, a signal sounds. A noti-
fication appears on the display confirming that the
operation has finished.
Once the cooking time has elapsed:
6.
If required, you can select other settings and re-
‒
start the operation.
When the food is ready, use
‒
pliance off.
Changing the end time
To achieve good cooking results, only change the set
time before the operation starts and before the cooking
time starts counting down.
Press
on the display.
1.
Press the end time
2.
Use the setting ring to change the end time.
3.
To confirm the change, press
4.
a The change is applied.
Cancelling the end time
You can delete the set end time at any time.
Press
on the display.
1.
Press the end time
2.
Use
to reset the end time.
3.
Note: For operating modes that always require a
cooking time, the appliance resets the time at which
the cooking time ends to the next possible time.
To confirm the change, press
4.
a The change is applied.
10.3 Setting the timer
The timer runs independently during the operation. You
can set the timer for up to 24 hours. The timer has its
own signal so that you can tell whether it is the timer or
a cooking time that has elapsed.
Press .
1.
To set the timer, press the relevant time value on
2.
the display, e.g. minute display "m" or second dis-
play "s".
a The selected value is marked in blue.
Set the timer using the setting ring.
3.
If required, use
to reset the setting value.
To start the timer, press
4.
a The timer counts down.
a The timer remains visible on the display if the appli-
ance is switched off.
a When the appliance is switched on, the display
shows the settings for the current operation. The
timer is displayed in the status display.
a Once the timer has elapsed, a signal sounds. A no-
tification appears on the display confirming that the
timer has finished.
Changing the timer
You can change the timer at any time.
1.
If the timer is running in the background, use
select the timer beforehand.
Press .
2.
Time-setting options en
to switch the ap-
.
on the display.
.
on the display.
on the display.
to
13
Advertisement
Table of Contents
