Siemens SIMATIC IPC BX-39A Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Industrial PC
  5. SIMATIC IPC BX-39A
  6. Operating instructions manual

Siemens SIMATIC IPC BX-39A Operating Instructions Manual

Hide thumbs Also See for SIMATIC IPC BX-39A:
Table of Contents

Advertisement

Quick Links

Download this manual
SIMATIC IPC BX-39A
SIMATIC
Industrial PC
SIMATIC IPC BX-39A
Operating Instructions
07/2022
A5E50715883-AA
Preface
Product description
Safety instructions
Installing and connecting
the device
Commissioning the device
Operating the device
Expanding and assigning
parameters to the device
Device maintenance and
repair
Technical specifications
Dimension drawings
Standards and approvals
Hardware description
Technical support
Markings and symbols
List of abbreviations
1
2
3
4
5
6
7
8
9
10
A
B
C
D

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMATIC IPC BX-39A

Summary of Contents for Siemens SIMATIC IPC BX-39A

  • Page 1 SIMATIC IPC BX-39A Preface Product description SIMATIC Safety instructions Installing and connecting the device Industrial PC SIMATIC IPC BX-39A Commissioning the device Operating the device Operating Instructions Expanding and assigning parameters to the device Device maintenance and repair Technical specifications...
  • Page 2 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.

  • Page 3: Preface

    General knowledge in the field automation control engineering is recommended. Scope of the operating instructions These operating instructions are valid for all order versions of the SIMATIC IPC BX-39A. History The following editions of these operating instructions have already been published:...
  • Page 4 Siemens' products and solutions undergo continuous development to make them more secure. Siemens strongly recommends that product updates are applied as soon as they are available and that the latest product versions are used. Use of product versions that are no longer supported, and failure to apply latest updates may increase customers' exposure to cyber threats.

  • Page 5: Table Of Contents

    Securing device ......................... 32 3.2.3 Mounting onto DIN rail ...................... 34 3.2.3.1 Attaching the DIN rail bracket .................... 34 3.2.3.2 Mounting on DIN rails ......................35 3.2.4 Wall mounting ........................36 3.2.5 Upright mounting ......................37 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 6 Installing/removing expansion modules (M.2) ..............61 Memory modules ....................... 64 6.5.1 Installing and removing a memory module ................ 64 Drives ..........................66 6.6.1 M.2 NVMe SSD in the SIMATIC IPC Slider ................66 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 7 Standards and approvals ........................89 10.1 CE marking ........................89 10.2 UKCA marking ........................90 10.3 DIN ISO 9001 certificate and software license agreements ..........90 10.4 UL approval ........................90 10.5 FCC (USA) .......................... 91 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 8 Markings and symbols ........................109 Overview ......................... 109 Safety ..........................109 Operator controls ......................109 Certificates, approvals and markings ................110 Interfaces ........................111 List of abbreviations .......................... 112 Abbreviations ........................112 Index ..............................114 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 9: Product Description

    -ipc-doku-portal) Firmware/BIOS description Information on: • Online at: • Important firmware settings Firmware/BIOS description • Firmware settings in the fac- SIMATIC IPC BX-39A, IPC PX-39A, tory state IPC PX-39A PRO (https://support.industry.siemens. • Boot modes com/cs/ww/en/view/109811365) Windows® operating sys- Information on: •...
  • Page 10 Information on: • Online at: bootable USB flash drive SIMATIC IPC Creating a bootable • Creating a bootable USB flash USB flash drive drive for recovery of operating (https://support.industry.siemens. system, software and drivers com/cs/ww/en/view/109811224) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 11: Product Highlights

    Product description 1.2 Product highlights Product highlights The SIMATIC IPC BX-39A is a powerful industrial Box PC. It is perfectly suited for PC applications with high-level industry functionality. Device view Note Depending on the configuration ordered the features and illustrations described in this manual may differ from the features of your device.

  • Page 12: Applications

    The SIMATIC IPC has CE certification for use in the industrial sector as well as in residential and commercial areas and small businesses. In addition to the industrial applications, therefore, it can also be used in building automation or in public facilities. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 13: External Design Of The Device

    SSD drives in NVMe format, installed in SIMATIC IPC Slider SSD1 X50/SSD2 X51 ⑩ Opening for expansion Interfaces of external expansion modules (M.2 format) interface X101 or COM2 X31 (optional) Serial interface 2 (V.24), 9-pin SUB-D socket (optional) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 14 Other device variants (Page 43): • with slot for one PCIe expansion card • with slots for two PCIe expansion cards You can find more information about expansion cards under "Expansion cards (Page 57)". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 15: Status Displays

    "Buffer memory NVRAM (optional) (Page 52)". Example programs for controlling the LEDs under Windows operating systems are available on the Internet at the following address: Technical support (https://support.industry.siemens.com) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 16 Figure 1-1 Interface_Ethernet_RJ45+LED displays2 Status display Status Meaning of the status LED 1 10 Mbps or 100 Mbps Lit orange 1000 Mbps LED 2 No connection Lit orange Connection exists Lit orange Activity SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 17: Internal Design Of The Device

    24 V DC power supply ② Slot for memory module ③ Motherboard ④ Backup battery ⑤ Slots for M.2 expansion modules (under removable drives) ⑥ Slot for removable drives (SSD) ⑦ Heat conduction pad SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 18: Accessories And Spare Parts

    Accessories and spare parts 1.6.1 Hardware accessories Accessories from Siemens are available for your device that are not included in the scope of delivery. Obtaining accessories from the SIEMENS Industry Mall 1. On the Internet, go to Industry Mall (https://mall.industry.siemens.com).

  • Page 19: Safety Instructions

    • Disconnect the device from the power supply in good time when a thunderstorm is approaching. • Do not touch power cables and data transmission cables during a thunderstorm. • Keep sufficient distance from electric cables, distributors, systems, etc. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 20 The device contains electronic components which may be destroyed by electrostatic charge. This can result in malfunctions and damage to the machine or plant. Take corresponding precautionary measures before you open the device. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 21: Note On Transport And Storage

    • Do not expose the device to direct heat radiation from a heating device. • If condensation develops, wait approximately 12 hours or until the device is completely dry before switching it on. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 22: Notes On Mounting

    When you plan your project, you should make allowances for: • The climatic and mechanical environmental conditions specified in the operating instructions. • Do not operate the device in severe operating conditions which are subject to caustic vapors or gases. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 23 • Switch off radiating devices. • Reduce the radio output of radiating devices. • Read the information on electromagnetic compatibility. • Read the information in the technical specifications. See also Ambient conditions (Page 78) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 24: Information On I/O Devices

    • The IPC in question must be turned off and the power supply connector must be plugged • During the measurement, all cables from the plant to the IPC should be connected. • All other components in the plant must be active. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 25: Notes On Device And System Extensions

    • UL approval of the device only applies when the UL-approved components are used according to their "Conditions of Acceptability". • We are not liable for functional limitations caused by the use of third-party devices or components. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 26: Installing And Connecting The Device

    You will find the latest information on additional software for your device under: Accessories and spare parts (Page 18) Printed documents • Quick Install Guide SIMATIC IPC BX-39A • Product Information "Important notes on your device" SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 27: Checking The Delivery Package

    If the contents of the package are incomplete, damaged or do not correspond to your order, you can use the After Sales Information System (ASIS) (http://siemens.com/asis) to provide feedback on product deliveries and repairs. Complete the online form for product delivery (quality control notification) under the heading "Product delivery: Feedback on quality control and repairs".

  • Page 28: Identification Data Of The Device

    The following illustrations are examples. The data of your device may differ from the data in these examples. Nameplate The following image shows the nameplate on the SIMATIC IPC BX-39A as an example. COA label The COA label (Certificate of Authenticity) is located on the rear of the device.

  • Page 29: Installing The Device

    • Above at least 50 mm • At least 50 mm at the side Note Observe the permitted temperature range for operation of the device in the respective mounting position as defined in section "Technical specifications (Page 74)". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 30 The interfaces are at the bottom. Wall mounting The interfaces are at the bottom. Suspended mounting position The suspended mounting position is permissible for wall mounting. The figure shows the interfaces on the front: SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 31 The vertical mounting position is permissible for wall and portrait mounting: Wall mounting Vertical mounting The interfaces are at The interfaces are the left. at the front. The power supply con- nection is at the top. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 32: Securing Device

    The device may not be securely fitted if you use anchors and screws other than those specified below for mounting. The device can fall and may be damaged. • Use only the specified anchors and screws. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 33 8 mm, 40 mm deep • Dowel, ∅ 8 mm, 40 mm length • Screw, ∅ 5 mm, 40 mm length Plasterboard, 14 mm Toggle bolt, ∅ 4 mm, 50 mm length min. 13 mm thickness SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 34: Mounting Onto Din Rail

    (as specified in order number). Requirements • 1 DIN rail clip • 4 screws • 1 T20 screwdriver Procedure 1. Secure the DIN rail bracket with four screws with a tightening torque of 2.5 Nm. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 35: Mounting On Din Rails

    You will hear the device click into place. Removal 1. Push down the device until it is released by the rail clips. 2. Swing the device out of the DIN rail. 3. Lift the device up and off. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 36: Wall Mounting

    (as specified in order number). Requirements • 2 wall mounting brackets • 6 screws • 1 T20 screwdriver Procedure 1. Secure the wall mounting brackets with three screws each and a tightening torque of 2.5 Nm. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 37: Upright Mounting

    (as specified in order number). Requirements • 2 vertical mounting brackets • 6 screws • 1 T20 screwdriver Procedure 1. Secure the portrait mounting brackets with three screws each and a tightening torque of 2.5 Nm. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 38: Connecting The Device

    2. Screw the cable lug onto the protective conductor connection as shown. 3. Wire the protective conductor to the protective conductor connection of the control cabi- net in which the device is installed. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 39: Connecting The Power Supply

    Make sure that the cores are connected to the correct terminals. Observe the labeling for the contacts on the device. 1. Connect the cables as shown with a tightening torque of 2.5 Nm. Make sure the connection terminal is in the correct position as shown. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 40: Connecting The 24 V Dc Power Supply

    The 24 V DC power supply is protected against polarity reversal. If you mix up the 24 V DC connecting cables and ground, the device is not damaged but does not switch on. After the power supply has been connected correctly, the device will again be ready to operate. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 41 The corresponding 24 V DC power supply is off. • 1 0.6 × 3.5 mm Philips screwdriver Procedure 1. Insert the terminal at the marked po- sition. 2. Secure the terminal using the inte- grated screws. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 42: Connecting I/O Devices

    The following table shows the various connection options for the monitors on the device interfaces. Motherboard DPP1 DPP2 Monitor 1 Monitor 2 1) - via DP to DVI-D adapter 2) - via DP-VGA adapter SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 43: Connecting Expansion Cards

    2. Connect the cable to one of the indicated slots. 3. Attach the cover at the points shown and close it. Make sure that the latching hooks snap into place so that the cover is secured. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 44: Connecting The Device To Networks

    Control level. You can find information on this under SIMATIC NET (http://w3.siemens.com/mcms/automation/en/industrial- communications/Pages/Default.aspx). The software package and the documentation are not included in the scope of delivery. Additional information You can find additional information on the Internet at: Technical Support (https://support.industry.siemens.com). SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 45: Securing The Lines

    2. Pass the cable tie around the strain relief bar and secure the cables as shown. 3. Cut off the protruding ends of the cable ties. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 46: Commissioning The Device

    Shutting down the operating system For active operating system • Shut down the operating system properly. Result The "POWER" operating display is lit yellow. The device is switched off but not fully disconnected from the line voltage. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 47 Perform a hardware reset only in the case of an emergency. • Operate the on/off switch to initiate a hardware reset, see "Interfaces and operating elements (Page 13)". See also General safety instructions (Page 19) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 48: Operating The Device

    2. Configure the function "multi-monitoring" in the firmware/BIOS settings of the device. You can find information on this in the detailed firmware/BIOS description, see "Important instructions and manuals for operating the device (Page 9)". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 49: Monitoring Of The Device

    You can find information on the monitoring software and its documentation under: • SIMATIC IPC DiagBase (Page 50) for monitoring and alarming locally on the device • SIMATIC IPC DiagMonitor (Page 50) for monitoring and alarming via network SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 50: Simatic Ipc Diagbase

    SIMATIC IPC DiagBase monitoring software is installed. Information on the software and documentation of SIMATIC IPC DiagBase can be found under: • SIMATIC IPC DiagBase (https://support.industry.siemens.com/cs/ww/en/view/109749690) • Important instructions and manuals for operating the device (Page 9) 5.2.3 SIMATIC IPC DiagMonitor The SIMATIC IPC DiagMonitor monitoring software can be ordered optionally.

  • Page 51: Remote Maintenance Of The Device

    You configure iAMT with Intel® Management Engine BIOS Extension (MEBx) in the firmware/BIOS. You can find information on this in the detailed firmware/BIOS description, see "Important instructions and manuals for operating the device (Page 9)". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 52: Trusted Platform Module (Tpm)

    A USB keyboard and mouse and a monitor can be connected later for diagnostics. A digital DVI monitor or DisplayPort monitor is only activated retrospectively when the Windows operating system has booted completed. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 53: Expanding And Assigning Parameters To The Device

    Take corresponding precautionary measures before you open the device. Requirements • The device is fully disconnected from the line voltage, see "Switching off the device (Page 46)". • All connecting cables are unplugged. • Screwdriver of type Torx T10 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 54 Expanding and assigning parameters to the device 6.1 Opening the Device Procedure 1. Remove the marked screws. 2. Lift off the front panel. 3. Put down the front panel. Close the device in reverse order. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 55: Open Device With Expansion Slots

    Take corresponding precautionary measures before you open the device. Requirements • The device is fully disconnected from the line voltage, see "Switching off the device (Page 46)". • All connecting cables are unplugged. • Screwdriver of type Torx T10 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 56 1. Remove the marked screws. 2. Lift off the front panel in the direction of the arrow. 3. Put down the front panel. Close the device in reverse order. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 57: Expansion Cards

    • You can find information on the type of expansion card you can install in specific slots under "Expansion card slots on the bus board (Page 96)". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 58 • If the PCIe card to be used has external interfaces, you can use the built-in slot plates to install the plug-in connectors. You can also use a slot plate with connector perforations. • Screwdriver of type Torx T10 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 59 Proceed in reverse order of installation. Configuring BIOS setup You may need to make settings in the BIOS Setup. For detailed information about installation, please refer to the documentation provided with the specific expansion card. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 60: Expansion Modules (M.2)

    • The connecting cable between M.2 modules and conditioner card should be at least 150 mm long. See also Position of the interfaces on the motherboard (Page 94) Dimension drawing of expansion modules (M.2) (Page 87) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 61: Installing/Removing Expansion Modules (M.2)

    Torx T10 and pull out the SSD drive bay upwards. Put down the SSD drive bay carefully on the side. Remove the designated screw on the motherboard with the screwdriver of the type Torx T8. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 62 Torx T10 screw- driver. Place the additional interface card from the inside against the empty enclosure opening and fasten it using the screw. Connect the cable of the interface card to the M.2 module. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 63 Proceed in reverse order of installation. Configuring BIOS setup You may need to make settings in the BIOS Setup. For detailed information about installation, please refer to the documentation provided with the specific expansion module. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 64: Memory Modules

    • Memory transaction rate 3200 MT/sec "unbuffered" • "without ECC" or "with ECC" Note Use only the memory modules recommended by Siemens AG. Requirement • The device is open, see important information regarding this under "Opening the Device (Page 53)" or "Open device with expansion slots (Page 55)".
  • Page 65 After insertion and removal Close the device. The new memory capacity will be automatically detected and displayed in the BIOS setup when the device is switched on. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 66: Drives

    • Screwdrivers of type Torx T10 and T8 Procedure - Option 1 If you change a drive together with Slider, then only steps 1 to 3 and then steps 12 and 13 need to be performed. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 67 Pull out the Slider in the direction of the arrow using the lug. Place the Slider on a suitable surface. Remove the marked screws with the screwdriver of type Torx T8. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 68 Remove the black plastic cover. Remove the marked screw with the screwdriver of type Torx T8. Remove the M.2 NVMe SSD from the Slider as shown. Carefully separate the M.2 NVMe SSD from the adapter plate. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 69 13. Place the Slider cover in the device and fasten it with the Torx T10 type screw- driver. Note To ensure reliable operation of the devices with SIMATIC IPC Slider, the Slider must be closed with the cover. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 70: Device Maintenance And Repair

    As soon as the Smart status of the data storage medium goes to "Not OK", a message is generated in SIMATIC IPC DiagBase or SIMATIC IPC DiagMonitor or also during a system start of the device. You should then back up your data and replace the drive. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 71: Removing And Installing Hardware

    (Page 9). • The device is open, see important information regarding this under Opening the Device (Page 53). • You have observed the local regulations relating to the disposal of used batteries. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 72: Installing Operating System, Software And Drivers

    Installing operating system, software and drivers You can restore the factory settings of the target system (i.e. the volume partitions, the operating system with installed device drivers, and the SIEMENS software products). This allows you to restore your device quickly if it has suffered damage.

  • Page 73: Configuring Firmware/Bios

    Contact a certified disposal service company for electronic scrap for environmentally sound recycling and disposal of your old device, and dispose of it according to the relevant regulations in your country. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 74: Technical Specifications

    Max. power consumption 67.5 W (at 24 V) Noise emission < 40 dB(A) according to DIN 45635-1 Degree of protection IP 20 according to IEC 60529 Quality assurance In accordance with ISO 9001 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 75 If the device is installed in an enclosure that complies with section 9.3.2. c) of IEC/UL/EN/DIN-EN 61010-1 and IEC/UL/EN/DIN-EN 61010-2-201, it can be supplied from a source "higher than NEC Class 2 / Limited Energy". The device is then classified as "OPEN EQUIPMENT". not evaluated by UL SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 76: Current/Power Requirements And Power Supply

    0.5 A 12 W NVMe SSDs in the SIMATIC IPC Slider - addi- 0.25 A 5.9 W tional M.2 slots - additionally 0.25 A 5.9 W PCIe slots - additionally 0.58 A 14 W SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 77: Technical Specifications Dc Power Supply (Dc)

    3 V/m 2.7 – 6 GHz, 80% AM to IEC 61000-4-3 • 10 V 10 KHz – 80 MHz, 80% AM to IEC 61000-4-6 Immunity to magnetic fields 100 A/m; 50 Hz; 60 Hz (according to IEC 61000-4-8) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 78: Ambient Conditions

    Temperature 25 °C - 55 °C, relative humidity 95% Air pressure - Operation 1080 to 689 hPa (corresponds to an altitude of -1000 to 3000 m) - Storage/transport 1080 to 660 hPa (corresponds to an altitude of -1000 to 3500 m) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 79 This information applies to the setting "Balanced" in the BIOS Setup, menu "Advanced" > "Power&Performance" > "CPU Power Management Control" > "Power & Performance Scenario"; the maximum ambient temperature must be reduced by 5 °C for the setting "Max Performance". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 80: Technical Specifications Of The Drives

    (Bus board 2 x PCIe) Slot 1 PCI Express x4 (mechanical x8): Specification Rev. 4.0, length: Max. 175 mm Slot 2 PCI Express x1 (mechanical x4): Specification Rev. 3.0, length: Max. 175 mm SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 81: Technical Specifications Of Graphic

    No teaming with AMT. When using AMT, the interface X1 P1 must be used for connection to remote maintenance. Only possible with ports X1 P1 and X2 P1 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 82: Technical Specifications Of The Operating Systems

    The following table lists the partitioning for disks ≥ 200 GB in GPT mode: Partition Name Size File system First Boot 260 MB FAT32 Second 128 MB None Third System 160 GB NTFS Fourth WinRE 500 MB NTFS Fifth Data Remainder NTFS SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 83: Dimension Drawings

    Dimension drawings Dimension drawing - mounting on a DIN rail SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 84: Dimension Drawing - Wall-Mounting

    Dimension drawings 9.2 Dimension drawing - wall-mounting Dimension drawing - wall-mounting SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 85: Dimension Drawing - Vertical Mounting

    Dimension drawings 9.3 Dimension drawing - vertical mounting Dimension drawing - vertical mounting SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 86: Dimension Drawing - Device With Expansion Slots

    Dimension drawings 9.4 Dimension drawing - device with expansion slots Dimension drawing - device with expansion slots Device with one PCIe slot Device with two PCIe slots SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 87: Dimension Drawing Of The Expansion Cards

    Dimension drawings 9.5 Dimension drawing of the expansion cards Dimension drawing of the expansion cards Dimension drawing of expansion modules (M.2) Maximum dimensions of expansion modules SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 88 Dimension drawings 9.6 Dimension drawing of expansion modules (M.2) Dimension drawing of the conditioner card SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 89: Standards And Approvals

    • 2011/65/EU "Restriction of the use of certain hazardous substances in electrical and electronic equipment" (RoHS Directive) EU Declaration of Conformity The associated declaration of conformity is available on the Internet at the following address: Certificate Box PC (http://support.automation.siemens.com/WW/view/en/10805671/134200). SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 90: Ukca Marking

    DIN ISO 9001 certificate and software license agreements ISO 9001 certificate The Siemens quality management system for our entire product creation process (development, production and sales) meets the requirements of ISO 9001. This has been certified by DQS (the German society for the certification of quality management systems).

  • Page 91: Fcc (Usa)

    (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible party for Supplier's Declaration of Conformity Siemens Industry, Inc. Digital Factory - Factory Automation 5300 Triangle Parkway, Suite 100 Norcross, GA 30092 mailto: amps.automation@siemens.com (mailto: amps.automation@siemens.com) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 92: Canada

    이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시기 바라며 가정 외의 지역에서 사용하는 것을 목적으로 합니다. 10.10 Taiwan Taiwan This product meets the requirements of the CNS14336-1(099/09/30), generic standard CNS13438(095/06/01). SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 93: Hardware Description

    Slots for expansion modules (M.2) ③ Backup battery ④ Slot for the bus board Technical features of the motherboard Technical features of the motherboard can be found under "Technical specifications of the motherboard (Page 80)". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 94: Position Of The Interfaces On The Motherboard

    (7) M.2 PCIe interface (X101) (11) USB 2.0 (X600 Internal (X1 P1 iAMT-capable/X2 (4) 2 × Ethernet (8) M.2 PCIe interface (X100) (12) USB 2.0 (X610 Internal (X3 P1/X4 P1) 4/X610 Internal 5) (13) Power supply (X10) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 95: Internal Interfaces

    Internal M.2 Key B, assigned PCIe bus signals Port for SSD drive bay Internal Socket for SSD drive bay, assigned PCIe bus signals A.2.2 USB ports Designation VBUS_USB1 VBUS_USB2 USB1_D- USB2_D- USB1_D+ USB2_D+ SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 96: Bus Board

    The bus board is available in the following designs: Variant 1 (1 slot) ① Slot X110 PCI Express x4 (mechanical x8) ② Power supply connection; see Pin assignment power supply connection for expansion cards (Page 97) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 97: Pin Assignment Power Supply Connection For Expansion Cards

    5 V voltage Output Ground + 3.3 V 3.3 V voltage Output max. permitted current: 1 A; with this power requirement, the total power requirement of the PCI slots must not be exceeded. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 98: External Interfaces

    9-pin SUB-D connector USB 3.2 X60, USB 3.2 Gen 2 socket type A X62, Ethernet 1, 2, X1 P1, RJ45 3 and 4 X2 P1, X3 P1, X4 P1 X70, 20-pin DisplayPort connector SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 99: System Resources

    WDT control register Base address + offset 6 WDT counter register Base address + offset 7 WDT status register The following tables describe the system resources for the factory state of the device. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 100: Output Register User Led L1/L2/L3 (Read/Write)

    LED L3 / Maint dark (default) LED L3 / Maint lit red LED L3 / Maint lights up green LED L3 / Maint lit yellow Reserved WDT system reset: On WDT system reset: Off SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 101: Battery Status Register (Read Only)

    Meaning of the bits Reserved Reserved Reserved CMOS battery capacity is still sufficient CMOS battery capacity is exhausted (remain- ing capacity is sufficient for approx. one month) CMOS battery is empty or missing Reserved Reserved Reserved SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 102: Watchdog Timer (Wdt) Register (Read/Write)

    This step resets the "PC ON/WD" LED from pulsing red to its normal state (lit green). The WDT starts counting down. To prevent this behavior, stop the WDT before resetting the status to "Active". SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 103 WDT counter register (read/write, address 286h) Bits Meaning of the bits 00h-FFh Countdown time WDT status register (read/write, address 287h) Bits Meaning of the bits Reserved Reserved Reserved Reserved WDT status: Active WDT status: Expired Reserved Reserved Reserved SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 104: Nvram Address Register

    NVRAM address register PCI register address: PCI register content: Length of the memory area NVRAM base address register NVRAM memory address (default) E300 0000 Address is assigned dynamically 80000 h (depending on device configura- tion) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 105: Technical Support

    You can find additional information and support for the products described on the Internet at the following addresses: • Technical support (https://support.industry.siemens.com) • Support request form (https://www.siemens.com/supportrequest) • After-sales information system for SIMATIC PC / PG (https://www.siemens.com/asis) • SIMATIC Documentation Collection (https://www.siemens.com/simatic-tech-doku-portal) • Your local representative (https://www.automation.siemens.com/aspa_app) • Training center (https://siemens.com/sitrain) •...

  • Page 106: Troubleshooting

    If you use an adapter or expansion for the mouse cable, also check these connectors. If the cursor still does not appear on the screen after you have performed these checks and actions, con- tact your technical support team. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 107 USB ports are disabled in the firm- Use a different USB port or activate the port. ware/BIOS Operating system does not support For other devices, you need the USB device drivers the USB port. for the required operating system. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 108: Problems When Booting The Device

    3. Set the respective setup parameter "PEG# - Gen X" perma- nently to "Gen1" in the "Advanced > Video Configuration" menu, submenu "Pci Expess Graphic" of the BIOS Setup. 4. Install the expansion card again. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 109: Markings And Symbols

    Disconnect the power plug before Opening for Kensington lock opening Attention ESD (Electrostatic sensitive Warning of hot surface device) Operator controls Symbol Meaning Symbol Meaning On/off switch, without electrical isola- On/off switch, without electrical isola- tion tion SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 110: Certificates, Approvals And Markings

    EFUP (Environment Friendly Use Pe- Approved for Korea riod) marking for China Test mark of the Underwriters Labora- UKCA marking for Great Britain tories Approval for India Disposal information, observe the lo- cal regulations. Approval for Taiwan SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 111: Interfaces

    LAN interface, not approved for con- Line Out necting WAN or telephone Serial port Microphone input USB port Universal Audio Jack USB 2.0 high-speed port Headphone output USB 3.0 super-speed port USB 3.1 SuperSpeedPlus interface SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 112: List Of Abbreviations

    Digital display interface with digital and VGA sig- nals Error checking and correction Error correction code Extensible Firmware Interface Electrostatic-sensitive components European standard Ground Chassis ground Hard Disk Drive Hard disk drive Height unit SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 113 US organization for tests and certifications accord- ing to own or binational standards (with CSA / Canada) standards. Universal Serial Bus Video Graphics Array Video adapter which meets industrial standard Watchdog Program monitoring with error detection and alarming. SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

  • Page 114: Index

    Expansion modules (M.2), 87 Marking Dimensions, 74 EU Declaration of Conformity, 89 Drive Mechanical ambient conditions, 79 Replace in the SIMATIC IPC Slider, 66 Memory media Drives, 75 Memory modules, 80 Motherboard Design, 93 SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...
  • Page 115 WinAC module, 97 Processor, 80 PROFIBUS, 44 PROFINET, 44 Protective conductor, 38 Connecting, 38 Quality control notification, 27 RJ45 Ethernet, 44 Safety instructions General, 19 Scope, 3 Securing the cables, 45 Setup, (BIOS Setup) SIMATIC IPC BX-39A Operating Instructions, 07/2022, A5E50715883-AA...

This manual is also suitable for:

Simatic ipc px-39a pro

Table of Contents