Motorola MSF 5000 Instruction Manual page 240

Appendix
B
Error Codes
MSF
5000
Instruction Manual
Digital Error Codes
Table B-3
Digital Error
Codes (Continued)
Error
Description
Probable Cause Corrective Action
d9b
SSCB IPCB faulty
¢
IPCB signal
(J800-11) grounded.
Replace SSCB
processor.
If failure
still occurs, replace SSCB.
¢
SSCB IPCB
interface circuitry.
¢
SSCB
microprocessor.
d9E
Config
register reprogrammed
Anew
un-initialized
processor
was No
actions required except to
installed on
the
SSCB.
program /
verify SSCB codeplug
data
Refer to the RSS manual.
d9F SSCB Config
register reprogrammed
An
un-initialized SSCB
processor
Reprogram SSCB codeplug. Refer
to
and codeplug erased
was installed.
the
RSS
manual.
dAO Non-zero user
area
check byte of
Station Reset occurred during user
Reprogram
the
TTRC
codeplug.
TTRC
area
EEPROM
update.
Refer to the
RSS
manual.
dAl
Non-zero
EEPROMCheck
byte of
Station
reset
during codeplug Reprogram
the
TTRC
codeplug.
TTRC
EEPROM
update.
Refer
to the
RSS manual.
dA2
e
Serial
EEPROM
has not responded
Missing
or defective
TTRC
serial
Install & program
serial EEPROM,
if
on
TTRC
EEPROM
device.
required.
If
not, reprogram
TTRC
codeplug
to
ignore serial
EEPROM.
codeplug programmed
to
expect
Refer
to the
RSS manual.
serial
EEPROM
when it is not
required or present.
dA3
Codeplug
on
TTRC
not
TTRC
type
The
TTRC
processor codeplug
Reprogram
the
TTRC
codeplug.
device recently replaced. Refer
to
the
RSS
manual.
dA4
Bad codeplug version number on
TTRC
codeplug version number
Upgrade
TTRC
firmware
to
latest
incompatible
with
TTRC
firmware version
or
reprogram
TTRC
version. codeplug. Refer to the
RSS
manual
if
necessary.
dA5
Bad codeplug checksum on
TTRC TTRC
codeplug is corrupt.
Reprogram
TTRC
codeplug.
dA6
Incorrect firmware checksum on
TTRC
firmware
EPROM
incorrect or
Replace
TTRC
firmware EPROM.
TTRC
defective.
dA7
TTRC
board not responding to ¢
TTRC
board not present when it
should
be.
*
Verify
TTRC
board is
properly
installed.
power-up
enable
e
Check
TTRC FAIL LED
for
¢
TTRC
IPCB interface circuitry.
©
TTRC
board has catastrophic
flashing
fatal error indication.
failure (processor won't run,
¢
Replace
TTRC
board,
if
necessary.
firmware missing,
etc.).
dA8&
TTRC
board enabled but
did
not
TTRC
board failed IPCB
tests,
Check
TTRC FAIL LED
for
flashing
return version number fatal error indication
indicating
a
failure in
one of the
following
circuits:
If no error indication, replace
TTRC
¢
TTRC
IPCB
interface
circuitry
board.
defective.
¢
TTRC
processor.
¢
Open IPCB runner
from
TTRC
IPCB interface to SSCB IPCB
interface.
dA9 TTRC
board station type does not
TTRC
codeplug recently replaced
/
Reprogram
the
TTRC
codeplug.
match SSCBs
programmed incorrectly.
Refer
to the
RSS manual.
TTRC
B-18
68P81092E09 3/14/94
Appendix
B
Error Codes
MSF
5000
Instruction Manual
Digital Error Codes
Table B-3
Digital Error
Codes (Continued)
Error
Description
Probable Cause Corrective Action
d9b
SSCB IPCB faulty
¢
IPCB signal
(J800-11) grounded.
Replace SSCB
processor.
If failure
still occurs, replace SSCB.
¢
SSCB IPCB
interface circuitry.
¢
SSCB
microprocessor.
d9E
Config
register reprogrammed
Anew
un-initialized
processor
was No
actions required except to
installed on
the
SSCB.
program /
verify SSCB codeplug
data
Refer to the RSS manual.
d9F SSCB Config
register reprogrammed
An
un-initialized SSCB
processor
Reprogram SSCB codeplug. Refer
to
and codeplug erased
was installed.
the
RSS
manual.
dAO Non-zero user
area
check byte of
Station Reset occurred during user
Reprogram
the
TTRC
codeplug.
TTRC
area
EEPROM
update.
Refer to the
RSS
manual.
dAl
Non-zero
EEPROMCheck
byte of
Station
reset
during codeplug Reprogram
the
TTRC
codeplug.
TTRC
EEPROM
update.
Refer
to the
RSS manual.
dA2
e
Serial
EEPROM
has not responded
Missing
or defective
TTRC
serial
Install & program
serial EEPROM,
if
on
TTRC
EEPROM
device.
required.
If
not, reprogram
TTRC
codeplug
to
ignore serial
EEPROM.
codeplug programmed
to
expect
Refer
to the
RSS manual.
serial
EEPROM
when it is not
required or present.
dA3
Codeplug
on
TTRC
not
TTRC
type
The
TTRC
processor codeplug
Reprogram
the
TTRC
codeplug.
device recently replaced. Refer
to
the
RSS
manual.
dA4
Bad codeplug version number on
TTRC
codeplug version number
Upgrade
TTRC
firmware
to
latest
incompatible
with
TTRC
firmware version
or
reprogram
TTRC
version. codeplug. Refer to the
RSS
manual
if
necessary.
dA5
Bad codeplug checksum on
TTRC TTRC
codeplug is corrupt.
Reprogram
TTRC
codeplug.
dA6
Incorrect firmware checksum on
TTRC
firmware
EPROM
incorrect or
Replace
TTRC
firmware EPROM.
TTRC
defective.
dA7
TTRC
board not responding to ¢
TTRC
board not present when it
should
be.
*
Verify
TTRC
board is
properly
installed.
power-up
enable
e
Check
TTRC FAIL LED
for
¢
TTRC
IPCB interface circuitry.
©
TTRC
board has catastrophic
flashing
fatal error indication.
failure (processor won't run,
¢
Replace
TTRC
board,
if
necessary.
firmware missing,
etc.).
dA8&
TTRC
board enabled but
did
not
TTRC
board failed IPCB
tests,
Check
TTRC FAIL LED
for
flashing
return version number fatal error indication
indicating
a
failure in
one of the
following
circuits:
If no error indication, replace
TTRC
¢
TTRC
IPCB
interface
circuitry
board.
defective.
¢
TTRC
processor.
¢
Open IPCB runner
from
TTRC
IPCB interface to SSCB IPCB
interface.
dA9 TTRC
board station type does not
TTRC
codeplug recently replaced
/
Reprogram
the
TTRC
codeplug.
match SSCBs
programmed incorrectly.
Refer
to the
RSS manual.
TTRC
B-18
68P81092E09 3/14/94