Table of Contents
Advertisement
MSF
5000
Instruction Manual
Chapter
3
Installation
Installation
Installation
The following procedures describe how
to
install
a
station into
the
permanent site
building. The
procedures include installation of nonstacked and stacked cabinets.
Nonstacked Cabinet Mounting
The following
procedures
are
for
flush wall, staggered back-to-back, and perfect
back-to-back mounting of nonstacked
cabinets.
Flush
Wall Mounting
1.
Remove
tip feet
if
required. Refer
to
"Tip
Feet
Removal"
on
page
3-18.
2.
Secure
the
cabinet
to the floor.
Refer
to
"Bottom
Anchoring"
on
page
3-19.
3.
Secure
the top
of
the
cabinet
to the
adjacent
wall. Refer
to
"Wall Support of
Cabinet"
on
page
3-14.
Staggered Back-to-Back
Mounting
NOTE
Stagger 46"
or 51" cabinets
by 1.5"
to
allow
for tip feet
clearance.
1.
Position
the
first cabinet. Refer to Figure
3-3.
2.
Secure
the
cabinet
to the
floor using all four holes in
the
tip
feet.
Refer
to
"Bottom Anchoring"
on
page
3-19.
3.
Position
the
other cabinet.
4.
Anchor
the
cabinet
to the floor.
Perfect Back-to-Back Mounting
1.
Remove
the
tip feet
if
required. Refer
to
"Tip
Feet
Removal"
on page 3-18.
2.
Secure
one
cabinet
to the floor.
Refer
to
"Bottom
Anchoring"
on page
3-19.
3.
Place
the
backs of
the cabinets 1.5"
apart and secure
the other
cabinet
to the
floor.
68P81092E03
3/19/94
3-9
MSF
5000
Instruction Manual
Chapter
3
Installation
Installation
Installation
The following procedures describe how
to
install
a
station into
the
permanent site
building. The
procedures include installation of nonstacked and stacked cabinets.
Nonstacked Cabinet Mounting
The following
procedures
are
for
flush wall, staggered back-to-back, and perfect
back-to-back mounting of nonstacked
cabinets.
Flush
Wall Mounting
1.
Remove
tip feet
if
required. Refer
to
"Tip
Feet
Removal"
on
page
3-18.
2.
Secure
the
cabinet
to the floor.
Refer
to
"Bottom
Anchoring"
on
page
3-19.
3.
Secure
the top
of
the
cabinet
to the
adjacent
wall. Refer
to
"Wall Support of
Cabinet"
on
page
3-14.
Staggered Back-to-Back
Mounting
NOTE
Stagger 46"
or 51" cabinets
by 1.5"
to
allow
for tip feet
clearance.
1.
Position
the
first cabinet. Refer to Figure
3-3.
2.
Secure
the
cabinet
to the
floor using all four holes in
the
tip
feet.
Refer
to
"Bottom Anchoring"
on
page
3-19.
3.
Position
the
other cabinet.
4.
Anchor
the
cabinet
to the floor.
Perfect Back-to-Back Mounting
1.
Remove
the
tip feet
if
required. Refer
to
"Tip
Feet
Removal"
on page 3-18.
2.
Secure
one
cabinet
to the floor.
Refer
to
"Bottom
Anchoring"
on page
3-19.
3.
Place
the
backs of
the cabinets 1.5"
apart and secure
the other
cabinet
to the
floor.
68P81092E03
3/19/94
3-9
Advertisement
Table of Contents
