Table of Contents
Advertisement
DESCRIPTION
The TC700 Series AutoDome™ systems are quiet,
lightweight, and discreet surveillance dome systems
containing high sensitivity 1/3-inch image format full
performance monochrome or color CCD cameras with a
10:1 auto-iris, auto-focus zoom lens, a high-speed
pan/tilt, and an intelligent, integral receiver/driver. The
one-piece camera, lens, pan/tilt, and receiver/driver
module is housed in a domed enclosure. They are
available in suspended ceiling, hard ceiling recessed,
surface, and pendant mount models. Pendant mount
models are available for indoor or outdoor applications.
INSTALLATION
Attention: Installation should be performed
by qualified
service
accordance with the National Electrical Code
or applicable local codes.
Attention: L'installation doit être effectuée
uniquement par du personnel de service
qualifié conformément à la réglementation du
Code
Electrique
réglementation locale.
Achtung! Die Installation sollte nur von
qualifiziertem Kundendienstpersonal gemäß
jeweilig zutreffender Elektrovorschriften aus-
geführt werden.
Atención: La instalación de este equipo debe
ser realizada por personal capacitado, solo
en acuerdo, y en cumplimiento de normas
del
"National
Eléctrico
Nacional)
Gobierno Nacional Local.
Removing Module From Carton
Refer to ILLUSTRATIONS for component description.
CAUTION: Keep in foil bag until grounded at
unit. Be sure to observe all safety measures
for static control when working with this unit
while out of its enclosure. Otherwise, static
damage may result.
For removal from foil bag and installation instructions,
see TC700 Series - Camera, Lens, Pan/Tilt, and
Receiver/Driver
Modules
INSTALLATION in the Installation and Operating
Instructions supplied with the particular Backbox
Module ordered.
CAUTION: Do not handle the unit by the
circuit board because this may result in
physical damage to the unit.
personnel
only in
National
ou
à
Electric
Code"
(Código
ó
las
normas
Installation
under
OPERATION
Camera Control
These units, as shipped, are factory adjusted as
described below:
Line-lock mode enabled with zero degree phase
delay.
AGC on.
Backlight compensation off.
Electronic shutter off.
Automatic white balance on (color cameras only).
Changing Operating Modes
The AutoDome unit operating modes can be changed
using either a TC8135B Series Controller/Follower or an
Allegiant series keyboard. An Allegiant series keyboard
is required to take full advantage of all the various
features
available.
description of various camera operating adjustments.
AutoDome Commands
Receiver/Driver - Using Auxiliary Controls
la
Receiver/Driver
Function
Scan
Auto-Pan
Pre-Position Tour
Set Scan/auto-pan
speed
Set tour period
Auto-Speed
del
Lens - Using Auxiliary Controls
Lens
Function
Iris Control
Focus Control
Auto-iris ALC adj
Auto-iris Level adj
Auto-focus
Activation
Auto-iris Activation
Auto-Speed (AUX 16)
Auto-speed On: Issuing this command provides
variable pan speed when unit is operated from a fixed
speed location. The pan speed starts slowly and
increases as the pan control is held on. The speed
resets to slow when the pan control is released. Note:
DIP Switch S2005.4 must be in the OFF position to use
this command; see DIP Switch Settings in the applicable
Installation and Operating Instructions for additional
information.
6
See
Camera
Commands
Aux
Description
On/Off
No.
1
Auto-pan without
On/off
limits
2
Auto-pan between
On/off
limits
8
--
On/off
14
--
Inc/dec
15
Sets pause between
Inc/dec
tour callups
16
Enables/disables
On/off
auto-speed
Aux
Description
On/Off
No.
3
--
Auto/
manual
4
--
Auto/
manual
10
--
Peak/ave
11
--
Inc/dec
12
Activates AF upon
On/off
movement
13
Activates AI upon
On/off
movement
for
Notes
5
--
--
2
2
2
Notes
1
1
1
1
2
2
Advertisement
Table of Contents
