THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
For Printed Wiring Boards.
Note:
• X : Parts extracted from the component side.
• Y : Parts extracted from the conductor side.
•
: Internal component.
f
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
Caution:
Pattern face side:
Parts on the pattern face side seen
(Conductor Side)
from the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(Component Side)
the parts face are indicated.
Caution:
Pattern face side:
Parts on the pattern face side seen
(SIDE B)
from the pattern face are indicated.
Parts face side:
Parts on the parts face side seen from
(SIDE A)
the parts face are indicated.
• Indication of transistor.
C
Q
These are omitted.
B
E
B
C E
These are omitted.
Note: When the complete MAIN board is replaced, refer to
"NOTE OF REPLACING THE IC104 ON THE MAIN
BOARD AND THE COMPLETE MAIN BOARD" on
page 3.
SWF-BR100
For Schematic Diagrams.
Note:
• All capacitors are in μF unless otherwise noted. (p: pF) 50
WV or less are not indicated except for electrolytics and
tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specifi ed.
•
: Internal component.
f
• 2 : Nonfl ammable resistor.
• 5 : Fusible resistor.
• C : Panel designation.
The components identifi ed by mark 0
or dotted line with mark 0 are critical for
safety.
Replace only with part number specifi ed.
Les composants identifi és par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce por-
tant le numéro spécifi é.
• A : B+ Line.
• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : POWER ON
• Voltages are taken with VOM (Input impedance 10 M).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F
: AUDIO
Note: When the complete MAIN board is replaced, refer to
"NOTE OF REPLACING THE IC104 ON THE MAIN
BOARD AND THE COMPLETE MAIN BOARD" on
page 3.
3-2.
PRINTED WIRING BOARD - LED Board -
1
LED BOARD
A
K
A
D801
K
A
D801
K
A
(RED)
/
K
A
(GRN)
R801
B
S801, 802
SECURE
CL804
CL801
CL803
C801
C802
1
CN801
5
C
CL802
WR1
>01P
3-3.
SCHEMATIC DIAGRAM - LED Board -
1
2
A
CN801
WR1
KEY_POWER
1
KEY_PAIR
2
>01S
GND
3
LED(G)
4
MAIN
BOARD
LED(R)
5
(1/2)
B
CN106
(Page 18)
C
15
15
•
: Uses unleaded solder.
2
3
LED BOARD
(SIDE A)
(SIDE B)
S801
/
R800
S802
CL808
CL805
CL806
CL800
CL809
CL807
11
11
1-889-753-
(11)
(11)
1-889-753-
MAIN BOARD
(Page 16)
CN106
3
4
LED BOARD
5P
CL808
CL804
CL809
CL803
C801
C802
CL807
CL802
0.1
0.1
CL806
CL801
CL805
CL800
S801
S802
SECURE
R800
220
(RED)
(GRN)
R801
680
D801
CL-165HR/HG5-D-T
SWF-BR100