Sony CMT-X5CD Service Manual

Sony CMT-X5CD Service Manual

Personal audio system
Hide thumbs Also See for CMT-X5CD:
Table of Contents

Advertisement

SERVICE MANUAL
Ver. 1.2 2014.06
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Amplifier section (US and Canadian models)
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(The United States model only)
With 8 ohm loads, both channels driven, from
120 - 10,000 Hz; rated 12 watts per channel
minimum RMS power, with no more than 0.7%
total harmonic distortion from 250 milliwatts to
rated output.
Power output (rated): 16 watts + 16 watts
(at 8 ohms, 1 kHz, 1% THD)
RMS power output (reference: 20 watts +
20 watts (per channel at 8 ohms, 1 kHz)
Amplifier section
(AEP, Russian, UK, Australian, Chinese,
Singapore and Korean models)
Power output (rated):
16 watts + 16 watts (at 8 ohms, 1 kHz, 1%
THD)
RMS power output (reference):
20 watts + 20 watts (per channel at 8 ohms,
1 kHz)
Inputs/Outputs
AUDIO IN:
AUDIO IN (external input) jack:
Stereo mini jack, sensitivity 700 mV,
impedance 47 kilohms
USB:
USB port: Type A, 5 V DC 1.5 A
9-893-964-03
Sony Corporation
2014F33-1
©
2014.06
Published by Sony Techno Create Corporation
Photo: CMT-X7CD
SPECIFICATIONS
DAB/DAB+ frequency table (Band-III):
CD-DA/MP3 player section
Frequency
System:
Compact disc and digital audio system
174.928 MHz
Laser Diode Properties:
176.640 MHz
Emission Duration: Continuous
Laser Output*: Less than 44.6 μW
178.352 MHz
* This output is the value measurement at a
distance of 200mm from the objective lens
180.064 MHz
surface on the Optical Pick-up Block with 7mm
aperture.
181.936 MHz
Frequency response:
183.648 MHz
20 Hz – 20 kHz
185.360 MHz
Signal-to-noise ratio:
More than 90 dB
187.072 MHz
Dynamic range:
188.928 MHz
More than 90 dB
190.640 MHz
Tuner section
192.352 MHz
FM tuner section:
FM stereo, FM superheterodyne tuner
194.064 MHz
Tuning range:
195.936 MHz
87.5 MHz – 108.0 MHz (100 kHz step)
(US, Canadian and Brazilian models)
197.648 MHz
87.5 MHz – 108.0 MHz (50 kHz step)
(AEP, Russian, UK, Australian, Chinese,
199.360 MHz
Singapore and Korean models)
201.072 MHz
Antenna:
FM lead antenna
202.928 MHz
Antenna terminals:
75 ohms unbalanced
204.640 MHz
DAB/DAB+ tuner section (CMT-X5CDB/X7CDB only):
206.352 MHz
FM stereo, DAB/FM superheterodyne tuner
Frequency range:
208.064 MHz
Band-III:
209.936 MHz
174.928 (5A) MHz – 239.200 (13F) MHz*
Antenna:
211.648 MHz
DAB/FM lead antenna:
CMT-X5CD/X5CDB/
X7CD/X7CDB
Canadian Model
Singapore Model
CMT-X5CD/X5CDB/X7CD/X7CDB
Australian Model
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Block Name
Frequency
Label
213.360 MHz
5A
215.072 MHz
5B
216.928 MHz
5C
218.640 MHz
5D
220.352 MHz
6A
222.064 MHz
6B
223.936 MHz
6C
225.648 MHz
6D
227.360 MHz
7A
229.072 MHz
7B
230.784 MHz
7C
232.496 MHz
7D
234.208 MHz
8A
235.776 MHz
8B
237.488 MHz
8C
239.200 MHz
8D
* Frequencies are displayed to two decimal places
on this system.
9A
9B
Speaker section
9C
Speaker system:
Full-range speaker
9D
Passive radiator
10A
Rated impedance:
8 ohms
10B
– Continued on next page –
PERSONAL AUDIO SYSTEM
US Model
Russian Model
Korean Model
CMT-X5CD
AEP Model
UK Model
CMT-X5CDB/X7CDB
CMT-X5CDB
Chinese Model
CMT-X7CD
NEW
CDM91-DVBU203
CMS-S76RFS7G1 or
CMS-S76RFS7GP
Label
10C
10D
11A
11B
11C
11D
12A
12B
12C
12D
13A
13B
13C
13D
13E
13F

Advertisement

Table of Contents
loading

Summary of Contents for Sony CMT-X5CD

  • Page 1 209.936 MHz 174.928 (5A) MHz – 239.200 (13F) MHz* Rated impedance: 8 ohms Antenna: 211.648 MHz DAB/FM lead antenna: – Continued on next page – PERSONAL AUDIO SYSTEM 9-893-964-03 Sony Corporation 2014F33-1 © 2014.06 Published by Sony Techno Create Corporation...
  • Page 2 The BLUETOOTH® word mark and logos are registered trademarks owned by BLUETOOTH SIG, Inc. and any use of such marks by Sony Corporation is under license. This appliance is classified as a CLASS 1 LASER The N Mark is a trademark or registered trademark of NFC Forum, Inc.
  • Page 3: Table Of Contents

    LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC- TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON- NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 4: Servicing Notes

    CMT-X5CD/X5CDB/X7CD/X7CDB SECTION 1 SERVICING NOTES NOTE OF REPLACING THE MS-091 BOARD NOTES ON HANDLING THE OPTICAL PICK-UP When the MS-091 board is defective, replace the LOADING BLOCK OR BASE UNIT ASSY (Ref. No. CDM1). The laser diode in the optical pick-up block may suffer electro-...
  • Page 5 CMT-X5CD/X5CDB/X7CD/X7CDB NOTE OF REPLACING THE WiFi MODULE (CMT-X7CD/ CHECKING METHOD OF NETWORK CONNECTION (CMT- X7CDB only) X7CD/X7CDB only) When replacing the WiFi module (Ref. No. WIFI1), MAC address It is necessary to check the network connection, when replacing and DEVICE_ID are changed. Print the page 7 and page 9, cut it, the WiFi module (Ref.
  • Page 6 4-528-188-0 [] (KR2) CMT-X7CD: Chinese model CMT-X5CD: Singapore model 4-528-181-0 [] (CN4) 4-528-189-0 [] (SP1) CMT-X7CDB: AEP and UK models CMT-X5CD: US and Canadian models 4-528-183-0 [] (CEL) 4-528-192-0 [] (UC2) CMT-X5CD: AEP model CMT-X5CDB: AEP and UK models 4-528-185-0 [] (CEL)
  • Page 7 CMT-X5CD/X5CDB/X7CD/X7CDB • Please cut out along the dotted line and use it. Note of the MAC address change: Note of the MAC address change: The MAC address of this unit was changed along with this repair. The MAC address of this unit was changed along with this repair.
  • Page 8 CMT-X5CD/X5CDB/X7CD/X7CDB MEMO...
  • Page 9 Please refer to the Operating Instructions “Listening to music on Win- Please refer to the Operating Instructions “Listening to music on Win- dows 8/Windows 7 (Home network)” or SONY Support site for the dows 8/Windows 7 (Home network)” or SONY Support site for the re-setup method.
  • Page 10 CMT-X5CD/X5CDB/X7CD/X7CDB MEMO...
  • Page 11 CMT-X5CD/X5CDB/X7CD/X7CDB HOW TO EJECT THE DISC WHEN POWER SWICTH TURN OFF • Refer to “SECTION 2. DISASSEMBLY”, remove the CD mechanism deck block from the unit 1 tape 3 Take out the disc. 2 Rotate the pulley in the direction of the arrow.
  • Page 12 CMT-X5CD/X5CDB/X7CD/X7CDB JACK BOARD SERVICE POSITION (X5CD/X5CDB) POWER KEY board CD mechanism deck block LCD board JACK board RC board insulating sheet power unit block MAIN board JACK-NET BOARD SERVICE POSITION (X7CD/X7CDB) POWER KEY board CD mechanism deck block LCD board...
  • Page 13: Disassembly

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW When disassembling the unit, use the following jig. Part No. Description 2-2. FRONT PANEL SUB ASSY 9-913-402-33 Tool for Disassembling (Page 14) 2-3.
  • Page 14: Front Panel Sub Assy

    CMT-X5CD/X5CDB/X7CD/X7CDB Note: Follow the disassembly procedure in the numerical order given. 2-2. FRONT PANEL SUB ASSY 1 Insert a thin pin etc. below the cap rear and slowly remove the cap rear. notch Note 2: Take care not to injure.
  • Page 15: Lcd Board Block

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-3. LCD BOARD BLOCK Note: When installing the flexible flat cable, ensure that the colored line is not slanted after insertion. short Insert is straight to the interior. Insert is incline long flexible flat flexible flat cable cable colored line...
  • Page 16: Bluetooth Module Block, Main Chassis Block-1

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-4. BLUETOOTH MODULE BLOCK, MAIN CHASSIS BLOCK-1 • Continued on 2-5 (page 17). Note 2: When you install the connector, please install them correctly. Wire setting There is a possibility that this machine damages when not bluetooth module (BT1) correctly installing it.
  • Page 17: Bluetooth Module Block, Main Chassis Block-2

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-5. BLUETOOTH MODULE BLOCK, MAIN CHASSIS BLOCK-2 • Continued on 2-6 (page 18). 1 four screws Note 1: When installing the flexible flat cable, (BVTP2.6) ensure that the colored line is not slanted after insertion. Insert is straight to the interior.
  • Page 18: Bluetooth Module Block, Main Chassis Block-3

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-6. BLUETOOTH MODULE BLOCK, MAIN CHASSIS BLOCK-3 Wire e i Note 1: When installing the flexible flat cable, ensure that the colored line is not slanted after insertion. Note 2: When installing the flexible flat cable, align the cables vertically.
  • Page 19: Bluetooth Module (Bt1)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-7. BLUETOOTH MODULE (BT1) 3 bluetooth module (BT1) Terminal face is below side. 1 adhesive (BT) 2 flexible flat cable (14P) (FFC9) flexible flat cable (14P) (FFC9) ferrite core (FC1) cushion (C)
  • Page 20: Flexible Flat Cable (9P)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-8. FLEXIBLE FLAT CABLE (9P) 1 BCO cushion Note: When installing the flexible flat cable, ensure that the colored line is not slanted after insertion. 2 flexible flat cable (24P) (CN503) Insert is straight to the interior.
  • Page 21: Cd Mechanism Deck Block

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-9. CD MECHANISM DECK BLOCK loading assy loading assy loading assy insulator insulator insulator step screw step screw There is no gap. There is gap. chassis chassis 5 CD mechanism deck block 4 two step screws Note 3: Pass the flexible flat cable underneath the main chassis.
  • Page 22: Ffc Guide

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-10. FFC GUIDE 2 cushion (FFC) guide line 1 cushion (touch) cushion (FFC) guide line cushion (touch) – CD mechanism deck block bottom view – FFC guide ferrite core (FC3) Note: When installing the FFC guide, make sure that this portion is not floating.
  • Page 23: Bottom Cover (I)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-11. BOTTOM COVER (I) 1 claw 2 two claws – CD mechanism deck block bottom view – 3 cover sheet 4 two screws (PTP2 4 two screws (PTP2 5 bottom cover (I)
  • Page 24: Optical Pick-Up (Cms-S76Rfs7G) (Op1)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-12. OPTICAL PICK-UP (CMS-S76RFS7G) (OP1) r e i bottom side short insulator long 4 flexible flat cable (24P) 6 insulator (FFC1) top side 7 optical pick-up (CMS-S76RFS7G) (OP1) 6 insulator 2 float screw (S) 6 insulator 5 connector 2 float 1 Remove the wire from three claws.
  • Page 25: Jack Board Block (X5Cd/X5Cdb)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-13. JACK BOARD BLOCK (X5CD/X5CDB) Note 2: When installing the flexible flat cable, ensure that the colored line is not slanted after insertion. Insert is straight to the interior. Insert is incline flexible flat flexible flat cable...
  • Page 26: Jack-Net Board Block-1 (X7Cd/X7Cdb)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-14. JACK-NET BOARD BLOCK-1 (X7CD/X7CDB) • Continued on 2-15 (page 27). Note 2: When installing the flexible flat cable, ensure that FFC cushion (USB) the colored line is not slanted after insertion. connector (CN2201) Insert is straight to the interior.
  • Page 27: Jack-Net Board Block-2 (X7Cd/X7Cdb)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-15. JACK-NET BOARD BLOCK-2 (X7CD/X7CDB) 1 five screws (BVTP3 7 connector (CN702) 3 JACK-NET board block MAIN board 4 two screws (BVTP3 5 bracket (jack) 6 flexible flat cable (9P) (CN002) 2 Remove the JACK-NET board block in the direction of the arrow.
  • Page 28: Rc Board Block

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-17. RC BOARD BLOCK 2 connector MAIN board MAIN board (CN601) Note 4: Insert the wire into the opening. Note 3: Pass the wire between the 1 connector – – connector and the capacitor. (CN004) Note 2: When affixing the cushion (K), be sure that it does not obstruct the hole.
  • Page 29: Tuner Board Block, Dab Board Block

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-18. TUNER BOARD BLOCK, DAB BOARD BLOCK 1 two screws (BVTP3 – Main chassis block front bottom view – 2 DAB board block 2 TUNER board block (X5CDB/X7CDB) (X5CD/X7CD)
  • Page 30: Lid (Power) Block

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-19. LID (POWER) BLOCK 1 BCO cushion 2 screw (BVTP3 3 bridge plate block 5 screw (BVTP3 Side with text. 4 AC inlet (2P) 5 three screws (AC1) (BVTP3 5 screw (BVTP3 Side without text. 6 lid (power) block –...
  • Page 31: Main Board Block

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-21. MAIN BOARD BLOCK 4 three screws (BVTP3 7 MAIN board block (X5CD/X5CDB) 6 connector 4 screw (CN901) (BVTP3 1 Remove the wire 5 Remove the MAIN board from the coating clip. block in the direction of the arrow.
  • Page 32: Main Board

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-22. MAIN BOARD C854 guide line flexible flat cable (15P) guide line IC503 sheet filament tape guide line (EMC-absober) (sub material) ferrite core (FC3) 4 filament tape (sub material) 5 sheet (EMC-absober) guide line 3 flexible flat cable (21P)
  • Page 33: Power Unit Block

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-23. POWER UNIT BLOCK 20 mm 2 two screws (BVTP3 sleeve ferrite cushion clamp (wire power) (FC7) 1 connector (CN201) 4 power unit block 2 screw (BVTP3 3 coating clip Note: When you install the connector, please install them correctly.
  • Page 34: Speaker (80 Mm) (Passive Radiator) (Sp3, Sp4)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-24. SPEAKER (80 mm) (PASSIVE RADIATOR) (SP3, SP4) 1 four screws (BVTP3 2 speaker (80 mm) 2 speaker (80 mm) (passive radiator: L-ch) (passive radiator: R-ch) (SP3) 1 four screws (SP4) (BVTP3 – Front bottom view – ire ettin...
  • Page 35: Loudspeaker (65 Mm) Block-1 (Sp1, Sp2)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 2-25. LOUDSPEAKER (65 mm) BLOCK-1 (SP1, SP2) • Continued on 2-26 (page 36). Note 2: When you install the connector, please install them correctly. There is a possibility that this machine damages when not CN102 RC board correctly installing it.
  • Page 36: Loudspeaker (65 Mm) Block-2 (Sp1, Sp2)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-26. LOUDSPEAKER (65 mm) BLOCK-2 (SP1, SP2) 1 four screws (BVTP3 4 loudspeaker (65 mm) block (L-ch) (SP1) 1 four screws 2 Remove the loudspeaker (BVTP3 (65 mm) block in the direction of the arrow. 4 loudspeaker (65 mm) block...
  • Page 37: Loudspeaker (65 Mm) (Full-Range Speaker) (Sp1)

    CMT-X5CD/X5CDB/X7CD/X7CDB 2-27. LOUDSPEAKER (65 mm) (FULL-RANGE SPEAKER) (SP1) loudspeaker (65 mm) (full-range speaker: L-ch) Note 2: To install the wire to the speaker (SP1) terminal, wrap only the conductor section of the wire around the speaker terminal and solder it in place.
  • Page 38: Test Mode

    Screen display (CMT-X5CD/X5CDB: 1.04, CMT-X7CD/X7CDB: 1.05) simultaneously for three seconds. 3. The message “RESET” (CMT-X5CD/X5CDB) or “ALLRESET” (CMT-X7CD/X7CDB) is displayed on the liquid crystal dis- play, then becomes the standby state. (Displayed values in the above fi gure are example) Screen display (CMT-X5CD/X5CDB) 4.
  • Page 39 2. Press the buttons on the remote commander in order of the SLEEP [ALPHABET SEARCH] → [1] → [ENTER]. (Press the next button within three seconds) 3. The message “RESET” (CMT-X5CD/X5CDB) or “ALLRESET” (CMT-X7CD/X7CDB) is displayed on the liquid crystal dis- cPLAY play, then becomes the standby state.
  • Page 40 CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 2-3. Panel Test MC version (CMT-X5CD/X5CDB: 1.04, It can confi rm the liquid crystal display, LEDs, model name, desti- USBM version CMT-X7CD/X7CDB: 1.05) nation, software version and buttons. Procedure: NWA version MCS version (CMT-X7CD/X7CDB only) 1. Press the [ ] button to turn the power on.
  • Page 41: Electrical Checks

    CMT-X5CD/X5CDB/X7CD/X7CDB SECTION 4 ELECTRICAL CHECKS 2-4. WiFi Reception Level (CMT-X7CD/X7CDB only) 2-5. Auto Standby Test 4. Check that “SET DISC” is displayed on the liquid crystal dis- TUNER SECTION 0 dB = 1 V It can display the reception level at the time of wireless LAN con- It can confi...
  • Page 42: Diagrams

    CMT-X5CD/X5CDB/X7CD/X7CDB SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM - CD/USB Section - OPTICAL PICK-UP BLOCK RF AMP, SERVO/AUDIO PROCESSOR (CMS-S76RFS7G) IC503 MTK-DATAO, MTK-BCK, MTK-LRCK, MTK-MCK MTK-DATAO >001B 123 RFIP GPIO MTK-BCK GPIO (Page 43) VOA/A 1 RFC MTK-LRCK GPIO VOB/B 128 RFB...
  • Page 43: Block Diagram - Audio Section

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-2. BLOCK DIAGRAM - AUDIO Section - MTK-DATAO, MTK-BCK, (X5CD/X5CDB) DIGITAL AUDIO MTK-LRCK, MTK-MCK MTK-DATAO >001B 6 1C0 SELECTOR AUDIO DSP, SYSTEM CONTROLLER DIGITAL POWER AMP IC709 IC204 (2/3) IC602 (Page 42) 28 I2S_DI_DSEL I2S_DAMP_DAC_SDA 16 SDIN SPK_OUTA+ 4 1C2...
  • Page 44: Block Diagram - Panel/Power Supply Section

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-3. BLOCK DIAGRAM - PANEL/POWER SUPPLY Section - REMOTE CONTROL RESET SIGNAL RECEIVER 135 SIRCS GENERATOR IC2101 IC205 LIQUID CRYSTAL DISPLAY DRIVER, POWER MONITOR B+ SWITCH POWER_MONITOR LED DRIVER Q911 Q912, 913 D919 IC5301 SEG4 – SEG35 40 DP-DI...
  • Page 45 CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. • Circuit Boards Location (In addition to this, the necessary note is printed in each block.) For Printed Wiring Boards. For Schematic Diagrams. – X5CD/X5CDB –...
  • Page 46: Printed Wiring Boards - Main Section (1/2)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-4. PRINTED WIRING BOARDS - MAIN Section (1/2) - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. OPTICAL PICK-UP (Page 62) (Page 61) BLOCK MS-091 (CMS-S76RFS7G) NFC MODULE TOUCH KEY Bluetooth >02P >03P BOARD...
  • Page 47: Printed Wiring Board - Main Section (2/2)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 5-5. PRINTED WIRING BOARD - MAIN Section (2/2) - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. MAIN BOARD (SIDE B) CL052 CL058 CL051 JL522 JL226 JL528 FB204 (X5CD/X7CD) JL526 CL046 R445...
  • Page 48: Schematic Diagram - Main Section (1/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 5-6. SCHEMATIC DIAGRAM - MAIN Section (1/8) - • See page 64 for Waveforms. • See page 64 for IC Block Diagrams. • See page 72 for IC Pin Function Description. MAIN BOARD (1/8) (Page 49) FE_VREFO FE_DVD_LDD >108S...
  • Page 49: Schematic Diagram - Main Section (2/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-7. SCHEMATIC DIAGRAM - MAIN Section (2/8) - • See page 64 for IC Block Diagrams. MAIN BOARD (2/8) CL863 R862 R868 C868 R875 R878 R879 R880 R881 R883 C872 R884 SL855 SL856 (4.9) (3.3) (0.9) (3.2) (3.2) R865 (4.9)
  • Page 50: Schematic Diagram - Main Section (3/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 5-8. SCHEMATIC DIAGRAM - MAIN Section (3/8) - • See page 64 for IC Block Diagrams. MAIN BOARD (3/8) MAIN STDBY_LED >122S BOARD KEY_WAKE (6/8) MAIN (Page 55) >113S (Page 53) BOARD PROTECT (8/8) D001 DA2J10100L DP-INH...
  • Page 51: Schematic Diagram - Main Section (4/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-9. SCHEMATIC DIAGRAM - MAIN Section (4/8) - • See page 64 for Waveforms. • See page 64 for IC Block Diagrams. MAIN BOARD (4/8) >129S (X5CD/X7CD) C742 C743 MAIN BOARD R799 (8/8) >116S (Page 55) I2S_DIN_TD MAIN I2S_BCK_TD...
  • Page 52: Schematic Diagram - Main Section (5/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-10. SCHEMATIC DIAGRAM - MAIN Section (5/8) - MAIN BOARD (5/8) CN202 JL212 MD BOOT1 JL213 R382 DAT2 JL214 MD BOOT0 JL215 R383 CD/DAT3 JL238 R447 LED GREEN JL217 JL216 R384 JL218 (NC) R385 C222 JL219 JL220 R386 DAT0...
  • Page 53: Schematic Diagram - Main Section (6/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 5-11. SCHEMATIC DIAGRAM - MAIN Section (6/8) - • See page 64 for Waveforms. • See page 64 for IC Block Diagrams. • See page 72 for IC Pin Function Description. MAIN (Page 52) >135S BOARD (5/8)
  • Page 54: Schematic Diagram - Main Section (7/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-12. SCHEMATIC DIAGRAM - MAIN Section (7/8) - • See page 64 for IC Block Diagrams. MAIN BOARD (7/8) >143S PA-GND MAIN C641 C640 BOARD 0.0022 0.0022 IC601 (8/8) (Page 55) PVDD-19.5V +3.3V REGULATOR IC601 BU33TD3WG-TR VOUT C658 Q601...
  • Page 55: Schematic Diagram - Main Section (8/8)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-13. SCHEMATIC DIAGRAM - MAIN Section (8/8) - • See page 64 for Waveforms. • See page 64 for IC Block Diagrams. MAIN BOARD (8/8) Q907 PVDD-19.5V RQ1E050RPTR MAIN Q906, 907 (Page 54) >143S BOARD B+ SWITCH CL905 JL903...
  • Page 56: Printed Wiring Board

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-14. PRINTED WIRING BOARD - JACK Board (X5CD/X5CDB only) - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. JACK BOARD JACK BOARD (COMPONENT SIDE) (CONDUCTOR SIDE) IC1501 C1519 L1502 C1521 R1509 D1506 CL1580 R1539...
  • Page 57: Schematic Diagram

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-15. SCHEMATIC DIAGRAM - JACK Board (X5CD/X5CDB only) - • See page 64 for Waveforms. • See page 64 for IC Block Diagrams. JACK BOARD NO1503 R1504 C1505 >04S CL1533 0.001 AUDIO-R CL1532 MAIN AGND CL1531 R1503 BOARD C1506...
  • Page 58: Printed Wiring Boards - Network Section (X7Cd/X7Cdb Only)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-16. PRINTED WIRING BOARDS - NETWORK Section (X7CD/X7CDB only) - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. ANTENNA BOARD PATTERN ANTENNA WIFI1 WIFI MODULE JACK-NET BOARD (COMPONENT SIDE) IC1501 R1558 C1521 L1502 R1533...
  • Page 59: Schematic Diagram - Network Section (X7Cd/X7Cdb Only)

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-17. SCHEMATIC DIAGRAM - NETWORK Section (X7CD/X7CDB only) - • See page 64 for Waveforms. • See page 64 for IC Block Diagrams. ANTENNA BOARD PATTERN ANTENNA WIFI1 WIFI MODULE (Page 51) JACK-NET BOARD NO1503 CN1505 >05S R1504 120P...
  • Page 60: Printed Wiring Board

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-18. PRINTED WIRING BOARD - ETHER Board (X7CD/X7CDB only) - 5-19. SCHEMATIC DIAGRAM - ETHER Board (X7CD/X7CDB only) - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. ETHER BOARD J001 MODULAR JACK ETHER BOARD...
  • Page 61: Printed Wiring Board - Rc Board

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-20. PRINTED WIRING BOARD - RC Board - 5-21. SCHEMATIC DIAGRAM - RC Board - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. RC BOARD RC BOARD (COMPONENT SIDE) IC2101 R2101 NO2101 R2104 CN2103...
  • Page 62: Printed Wiring Board - Lcd Board

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-22. PRINTED WIRING BOARD - LCD Board - • See page 45 for Circuit Boards Location. • : Uses unleaded solder. LCD BOARD (COMPONENT SIDE) R5311 Q5303 C5301 Q5301 R5316 R5315 R5317 R5314 R5304 R5302 IC5301 R5303 (11) 1-889-811-...
  • Page 63: Schematic Diagram - Lcd Board

    CMT-X5CD/X5CDB/X7CD/X7CDB 5-23. SCHEMATIC DIAGRAM - LCD Board - • See page 64 for IC Block Diagrams. LCD BOARD ND5301 LIQUID CRYSTAL DISPLAY R5313 C5304 C5301 4.7k 0.047 COM2 SEG12 COM3 SEG24 COM1 SEG13 R5311 COM4 SEG23 C5302 4.7k SEG1 SEG14...
  • Page 64 CMT-X5CD/X5CDB/X7CD/X7CDB • Waveforms • IC Block Diagrams – MAIN Board – – JACK Board – – MAIN Board – IC005, 601, 707 BU33TD3WG-TR IC503 8 (XTALO) IC708 9 (3Y) IC204 yk (RTC_X2) IC1506 1 (BOOT) VOLTAGE – REFERENCE VOUT OVER CURRENT 1.7 Vp-p...
  • Page 65 CMT-X5CD/X5CDB/X7CD/X7CDB IC505, 905 MM3374A33PRE VOUT CE 1 BIAS THERMAL CURRENT VOLTAGE SHUTDOWN LIMIT REFERENCE GND 2 NC 3 IC602 TAS5760MDAPR AVDD 1 INTERNAL REFERENCE REGULATORS SFT_CLIP 2 ANA_REG 3 GVDD_REG VCOM 4 GGND ANA_REF 5 INTERNAL GATE SPK_FAULT 6 DRIVE REGULATOR...
  • Page 66 CMT-X5CD/X5CDB/X7CD/X7CDB IC706 PCM1808PWR ANTIALIAS VINR LOW-PASS FILTER ANTIALIAS VINL LOW-PASS FILTER DELTA-SIGMA MODULATOR 1/64 SERIAL DECIMATION INTERFACE FILTER VREF 1 REFERENCE & WITH MODE/FORMAT DOUT HIGH-PASS CONTROL DELTA-SIGMA FILTER MODULATOR AGND POWER SUPPLY DGND CLOCK & TIMING CONTROL SCKI 6...
  • Page 67 CMT-X5CD/X5CDB/X7CD/X7CDB IC852 AM5890S MUTE MUTE BIAS VINFC 1 VINTK TRB1 2 REGO2 3 TRB2 VOLTAGE RESET DETECTION VINSL+ 4 VINLD REGO1 5 VCTL VCCD FWD 6 VCC2 DRIVER REV 7 VCC2 SPINDLE VOLD– VCC1 DRIVER (4x) VCC2 VOLD+ VCC1 VOTK–...
  • Page 68 CMT-X5CD/X5CDB/X7CD/X7CDB IC907 BD9A100MUV-E2 PVIN 1 PVIN 2 VREF CURRENT COMPARATOR GM AMP – – PGOOD – SLOPE CURRENT SENSE/ PROTECT & AVIN DRIVER LOGIC PVIN UVLO PGND 3 PGND 4 SOFT START – JACK Board – IC1501 BD82034FVJ-GE2 IC1507 BD11600NUX-E2...
  • Page 69 CMT-X5CD/X5CDB/X7CD/X7CDB IC1506 TPS54332CDDAR 8 PH 7 GND BOOT MAXIMUM BOOT 1 UNDERVOLTAGE 6 COMP CLAMP LOCKOUT BOOT THERMAL CHARGE SHUTDOWN DISCHARGE LOGIC ECO-MODE MINIMUM CLAMP VIN 2 ENABLE COMPARATOR SHUTDOWN VOLTAGE ENABLE THRESHOLD LOGIC LATCH REFERENCE GATE COMPARATOR DRIVE LOGIC –...
  • Page 70 CMT-X5CD/X5CDB/X7CD/X7CDB IC1504 S-13A1A12-E6T1U3 VOUT 1 OVERCURRENT PROTECTION THERMAL SHUTDOWN ON/OFF CONTROL – REFERENCE VOLTAGE VSS 2 ON/OFF 3 INRUSH CURRENT LIMITING IC1505 MM3411A33NRE VDD 1 GND 2 VOUT CURRENT LIMIT VOLTAGE REFERENCE CE 3 BIAS IC1506 TPS54332CDDAR 8 PH 7 GND...
  • Page 71 CMT-X5CD/X5CDB/X7CD/X7CDB IC1507 BD11600NUX-E2 1D+ 1 1D– 2 D– 2D+ 3 2D– 4 GND 5 CONTROL – LCD Board – IC5301 PT16511-LQ 38 37 COMMON COM2 DRIVER COM1 CLOCK GENERATOR ADDRESS DETECTOR DRIVER SHIFT REGISTER SEG1/GP1/PW1 1 SEG2/GP2/PW2 2 SEG3/GP3/PW3 3...
  • Page 72 I2S_DAMP_ Master clock signal output to the digital power amplifi er DAC_MCLK DAMP_CARRIER/ Frequency selection signal output to the digital power amplifi er (CMT-X5CD/X7CD) DAB_RX Serial data input from the DAB board (CMT-X5CDB/X7CDB) Power on/off control signal output terminal “H”: power on (CMT-X5CD/X7CD)
  • Page 73 POWER-AMP Power on/off control signal output terminal for amplifi er section “H”: power on Power supply terminal (+1.2V) Serial data output to the NFC module (CMT-X5CD/X5CDB) NFC_DATA/ Power on/off control signal output terminal for the network section “H”: power on POWER_BCO1.2...
  • Page 74 Muting control signal output to the digital power amplifi er I2C_SCL_CP Two-way I2C clock signal bus with the MFI I2C_SDA_CP Two-way I2C data bus with the MFI Two-way I2C clock signal bus with the TUNER board (CMT-X5CD/X7CD) I2C_SCL_TU/5V_ON Power on/off control signal output terminal “H”: power on (CMT-X5CDB/X7CDB) I2C_SDA_TU/...
  • Page 75 Main power on/off control signal output terminal “H”: power on PVCC Power supply terminal (+3.3V) NFC_SEL/ Data read/write control signal output to the NFC module (CMT-X5CD/X5CDB) RESET_BCO Reset signal output to the WiFi module “L”: reset (CMT-X7CD/X7CDB) NFC_IRQ/ Interrupt request signal input from the NFC module (CMT-X5CD/X5CDB)
  • Page 76 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN BOARD IC503 CXD90013R (RF AMP, SERVO/AUDIO PROCESSOR) Pin No. Pin Name Description RF main beam (A) input from the optical pick-up block RF main beam (D) input from the optical pick-up block RF sub beam (F) input from the optical pick-up block...
  • Page 77 CMT-X5CD/X5CDB/X7CD/X7CDB Pin No. Pin Name Description DVSS12 Ground terminal (digital system) Column address strobe signal output to the SD-RAM Row address strobe signal output to the SD-RAM DVDD33 Power supply terminal (+3.3V) (digital system) 85, 86 BA0, BA1 Bank address signal output to the SD-RAM DVDD12 Power supply terminal (+1.2V) (digital system)
  • Page 78: Exploded Views

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 SECTION 6 EXPLODED VIEWS Note: • -XX and -X mean standardized parts, so • Color variations • Abbreviation they may have some difference from the CMT-X5CD : Australian model original one. (B) Black : US, CND, AEP, RU, SP, KR : Chinese model •...
  • Page 79: Lcd Board Section

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 6-2. LCD BOARD SECTION rear panel section FFC9 FFC3 supplied FFC8 FFC11 (X7CD/X7CDB) not supplied not supplied RC board section (LCD board) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-218-253-32 SCREW (M2.6), +BTTP...
  • Page 80: Rc Board Section

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 6-3. RC BOARD SECTION (X7CD/X7CDB) not supplied (X5CD/ X5CDB) not supplied (X5CDB/X7CDB) MAIN board section DAB board section FFC7 (X5CD/X7CD) TUNER board section CD mechanism deck section not supplied (RC board) Ref. No. Part No. Description Remark Ref.
  • Page 81: Main Board Section

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 6-4. MAIN BOARD SECTION • Rear view (X5CD/X5CDB) (X7CD/X7CDB) not supplied FFC10 supplied (X7CD/X7CDB) not supplied supplied FFC6 supplied supplied not supplied WIFI1 power unit section not supplied (X7CD/X7CDB) not supplied Note: When the WiFi module (Ref. No. WIFI1) is replaced, refer to “NOTE OF REPLACING THE WiFi MODULE (CMT-X7CD/X7CDB only)”, “PROCESSING OF REPLACING THE WiFi MODULE (CMT-X7CD/X7CDB...
  • Page 82: Power Unit Section

    CMT-X5CD/X5CDB/X7CD/X7CDB 6-5. POWER UNIT SECTION • Rear view not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied not supplied PWR1 not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No.
  • Page 83: Cd Mechanism Deck Section (Cdm91-Dvbu203)

    CMT-X5CD/X5CDB/X7CD/X7CDB 6-6. CD MECHANISM DECK SECTION (CDM91-DVBU203) FFC2 optical pick-up section CDM1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-674-137-01 SCREW (PTP2X5) CDM1 A-1924-332-A LOADING ASSY 2-345-115-01 SCREW (S), FLOAT (Including MS-091 board, loading motor)
  • Page 84: Optical Pick-Up Section

    CMT-X5CD/X5CDB/X7CD/X7CDB 6-7. OPTICAL PICK-UP SECTION FFC1 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-456-402-01 INSULATOR FFC1 9-885-193-81 FY14 FFC (0.5 mm_24P_CD OP) 4-418-987-01 SHEET (S76) 0 OP1 A-1940-584-A OPTICAL PICK-UP (CMS-S76RFS7G) 1-469-829-11 CORE, FERRITE...
  • Page 85: Tuner Board Section (X5Cd/X7Cd)

    CMT-X5CD/X5CDB/X7CD/X7CDB 6-8. TUNER BOARD SECTION (X5CD/X7CD) FFC4 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1924-242-A TUNER BOARD, COMPLETE 1-500-635-11 CORE, FERRITE 4-436-234-01 CUSHION (TOUCH) 4-466-963-01 CUSHION, BCO FFC4 9-885-193-74 FY14 FFC (1.0 mm_9P_RICOH TUNER)
  • Page 86: Dab Board Section (X5Cdb/X7Cdb)

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.1 6-9. DAB BOARD SECTION (X5CDB/X7CDB) not supplied CN01 DAB1 not supplied not supplied FFC5 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-465-844-01 CUSHION, FFC (USB) CN01 1-843-261-11 PIN HEADER 2P...
  • Page 87: Rear Panel Section

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 6-10. REAR PANEL SECTION (X7CD/X7CDB) ANT1 not supplied not supplied not supplied not supplied (X7CD/X7CDB) Note 1: When the WIFI ANTENNA 2.4 GHz SVX (Ref. No. ANT1) is replaced, refer to “CHECKING METHOD OF NETWORK CONNECTION (CMT-X7CD/X7CDB only)” on page 5.
  • Page 88: Electrical Parts List

    CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 SECTION 7 ANTENNA ELECTRICAL PARTS LIST ETHER JACK Note: • Due to standardization, replacements in • CAPACITORS When indicating parts by reference num- the parts list may be different from the uF: μF ber, please include the board name.
  • Page 89 CMT-X5CD/X5CDB/X7CD/X7CDB JACK JACK-NET Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1521 1-218-973-11 METAL CHIP 1/16W C1552 1-116-737-11 CERAMIC CHIP 1uF R1522 1-218-965-11 METAL CHIP 1/16W C1553 1-100-905-11 CERAMIC CHIP 0.001uF C1554 1-100-916-11 CERAMIC CHIP 0.1uF...
  • Page 90 CMT-X5CD/X5CDB/X7CD/X7CDB JACK-NET Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R1524 1-216-809-11 METAL CHIP 1/10W R1591 1-218-990-81 SHORT CHIP R1525 1-216-809-11 METAL CHIP 1/10W R1592 1-218-990-81 SHORT CHIP R1526 1-216-821-11 METAL CHIP 1/10W R1593 1-218-990-81 SHORT CHIP...
  • Page 91 CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1987-631-A MAIN BOARD, COMPLETE (X7CD: AEP) C229 1-118-347-11 CERAMIC CHIP 0.1uF A-1987-634-A MAIN BOARD, COMPLETE (X7CDB) C230 1-164-850-11 CERAMIC CHIP 10PF 0.5PF A-1987-635-A MAIN BOARD, COMPLETE (X5CD: AEP)
  • Page 92 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C551 1-164-874-11 CERAMIC CHIP 100PF * C657 1-118-360-11 CERAMIC CHIP 0.1uF C553 1-118-391-11 CERAMIC CHIP 0.01uF C658 1-116-717-11 CERAMIC CHIP 10uF C659 1-116-717-11 CERAMIC CHIP 10uF...
  • Page 93 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C873 1-118-391-11 CERAMIC CHIP 0.01uF * C999 1-116-714-11 CERAMIC CHIP 22uF 6.3V C878 1-118-386-11 CERAMIC CHIP 0.1uF * C1000 1-116-714-11 CERAMIC CHIP 22uF 6.3V C879 1-118-386-11 CERAMIC CHIP 0.1uF...
  • Page 94 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark FB516 1-400-580-21 FERRITE, EMI (SMD) Q005 6-552-922-01 TRANSISTOR LTA014EUBFS8TL FB517 1-481-348-21 EMI FERRITE (SMD) (1608) (X7CD/X7CDB) FB518 1-481-348-21 EMI FERRITE (SMD) (1608) Q006 6-552-936-01 TRANSISTOR LTC014EUBFS8TL...
  • Page 95 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R030 1-216-864-11 SHORT CHIP 0 (X7CD/X7CDB) R224 1-218-941-81 METAL CHIP 1/16W R031 1-216-864-11 SHORT CHIP 0 (X7CD/X7CDB) (X7CD/X7CDB) R032 1-218-969-11 METAL CHIP 1/16W R225 1-218-941-81 METAL CHIP...
  • Page 96 CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R309 1-218-973-11 METAL CHIP 1/16W R382 1-218-941-81 METAL CHIP 1/16W (X7CD/X7CDB) R316 1-218-941-81 METAL CHIP 1/16W R383 1-218-941-81 METAL CHIP 1/16W R384 1-218-941-81 METAL CHIP...
  • Page 97 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R460 1-218-961-11 METAL CHIP 4.7K 1/16W R605 1-218-965-11 METAL CHIP 1/16W (X5CDB/X7CDB) R606 1-218-929-11 METAL CHIP 1/16W R502 1-218-958-11 METAL CHIP 2.7K 1/16W R609 1-216-864-11 SHORT CHIP...
  • Page 98 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R777 1-218-937-11 METAL CHIP 1/16W R874 1-218-967-11 METAL CHIP 1/16W (X7CD/X7CDB) R875 1-211-973-11 METAL CHIP 0.5% 1/10W R778 1-218-937-11 METAL CHIP 1/16W R876 1-218-977-11 METAL CHIP...
  • Page 99 CMT-X5CD/X5CDB/X7CD/X7CDB MAIN MS-091 POWER KEY TOUCH KEY TUNER Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R965 1-218-953-11 METAL CHIP 1/16W < VIBRATOR > R966 1-250-519-11 METAL CHIP 1/16W X201 1-814-466-11 QUARTZ CRYSTAL UNITS (12.288 MHz)
  • Page 100 CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark DAB1 1-489-807-11 MODULE (DAB TUNER) (X5CDB/X7CDB) X-2589-310-1 PANEL, REAR SVX (X5AU) 1-481-359-11 CORE, FERRITE (Including NFC module, POWER KEY board, 1-469-829-11 CORE, FERRITE TOUCH KEY board) (for BLACK) (X5CDB: AUS)
  • Page 101 CMT-X5CD/X5CDB/X7CD/X7CDB Ver. 1.2 Ref. No. Part No. Description Remark 4-528-300-92 QSG (Quick Start Guide) (SIMPLIFIED CHINESE) (X7CD: CH) 4-528-303-13 MANUAL, INSTRUCTION (ENGLISH) (X5CD: US, CND) 4-528-303-23 MANUAL, INSTRUCTION (FRENCH) (X5CD: US, CND) 4-528-304-13 MANUAL, INSTRUCTION (ENGLISH) (X5CD: SP/X5CDB: UK, AUS)
  • Page 102 (JACK) and FFC CUSHION (USB) (3 pieces: X5CD/X5CDB, 4 pieces: X7CD/X7CDB) (SMR-13061) 2014.06 Addition of Singapore and Korean models (CMT-X5CD) Deletion of Black color type (AEP model (CMT-X7CD/X7CDB)) Change of Part No. for INSTRUCTION MANUAL and Quick Start Guide (SMR-14010)

This manual is also suitable for:

Cmt-x5cdbCmt-x7cdCmt-x7cdb

Table of Contents