Sony CMT-X5CD Operating Instructions

4-528-303-13(1)
Personal Audio System
GB Operating Instructions
©2014 Sony Corporation Printed in China
CMT-X5CD
The unit is not disconnected from the mains as
long as it is connected to the AC outlet, even if
the unit itself has been turned off.
CAUTION
The use of optical instruments with this product
will increase eye hazard.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN
HAZARD
The remote control supplied with this product
Owner's Record
contains a coin/button cell battery.
The model and serial numbers are located on
If the coin/button cell battery is swallowed, it
the bottom exterior of the unit. Record these
can cause severe internal burns in just 2 hours
numbers in the space provided below. Refer to
and can lead to death.
them whenever you call upon your Sony dealer
Keep new and used batteries away from
regarding this product.
Model No. children. If the battery compartment does not
Serial No. close securely, stop using the product and keep
it away from children.
If you think batteries might have been
swallowed or placed inside any part of the body,
WARNING
seek immediate medical attention.
Important Safety Instructions
For the State of California, USA only
1) Read these instructions.
Perchlorate Material-special handling may
2) Keep these instructions.
apply, See
3) Heed all warnings.
www.dtsc.ca.gov/hazardouswaste/
4) Follow all instructions.
perchlorate
5) Do not use this apparatus near water.
Perchlorate Material : Lithium battery contains
6) Clean only with dry cloth.
perchlorate
7) Do not block any ventilation openings.
Install in accordance with the manufacturer's
To reduce the risk of fire or electric shock, do
instructions.
not expose this apparatus to rain or moisture.
8) Do not install near any heat sources such
To reduce the risk of fire, do not cover the
as radiators, heat registers, stoves, or other
ventilation opening of the appliance with apparatus (including amplifiers) that produce
newspapers, tablecloths, curtains, etc.
heat.
Do not expose the appliance to naked flame 9) Do not defeat the safety purpose of the
sources (for example, lighted candles). polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
To reduce the risk of fire or electric shock, do not
other. A grounding type plug has two blades
expose this appliance to dripping or splashing,
and do not place objects filled with liquids, such and a third grounding prong.
The wide blade or the third prong are
as vases, on the appliance.
provided for your safety. If the provided
Do not install the appliance in a confined space,
plug does not fit into your outlet, consult an
such as a bookcase or built-in cabinet.
electrician for replacement of the obsolete
As the main plug is used to disconnect the unit
outlet.
from the mains, connect the unit to an easily
10) Protect the power cord from being walked on
accessible AC outlet. Should you notice an or pinched particularly at plugs, convenience
abnormality in the unit, disconnect the main
receptacles, and the point where they exit
plug from the AC outlet immediately.
from the apparatus.
The nameplate is located on the bottom exterior. 11) Only use attachments/accessories specified
by the manufacturer.
These following indications are located on the
12) Use only with the cart, stand, tripod,
bottom exterior.
bracket, or table specified by the
manufacturer, or sold with the
apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
This symbol is intended to alert 13) Unplug this apparatus during lightning
the user to the presence of storms or when unused for long periods of
uninsulated"dangerous voltage"
time.
within the product's enclosure that 14) Refer all servicing to qualified service
may be of sufficient magnitude to
personnel.
constitute a risk of electric shock to Servicing is required when the apparatus
persons. has been damaged in any way, such as
power-supply cord or plug is damaged,
This symbol is intended to alert the
liquid has been spilled or objects have fallen
user to the presence of important
into the apparatus, the apparatus has been
operating and maintenance
exposed to rain or moisture, does not operate
(servicing) instructions in the
normally, or has been dropped.
literature accompanying the
appliance.
The following FCC statement applies only
to the version of this model manufactured
CAUTION
for sale in the U.S.A. Other versions may
Danger of explosion if battery is incorrectly not comply with FCC technical regulations.
replaced. Replace only with the same or
equivalent type.
Do not expose batteries or appliances with
battery-installed to excessive heat, such as
sunshine and fire.
NOTE: ˎThe BLUETOOTH® word mark and logos are
This equipment has been tested and found to registered trademarks owned by BLUETOOTH
comply with the limits for a Class B digital device, SIG, Inc. and any use of such marks by Sony
Corporation is under license.
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection ˎThe N Mark is a trademark or registered
against harmful interference in a residential
trademark of NFC Forum, Inc. in the United
installation. This equipment generates, uses States and in other countries.
and can radiate radio frequency energy and, if
ˎAndroid and Google Play are trademarks of
not installed and used in accordance with the
Google Inc.
instructions, may cause harmful interference
ˎThe system names and product names
to radio communications. However, there is
indicated in this manual are generally the
no guarantee that interference will not occur
trademarks or registered trademarks of the
in a particular installation. If this equipment
manufacturer. ™ and ® marks are omitted in
does cause harmful interference to radio or
this manual.
television reception, which can be determined
ˎ"WALKMAN" and "WALKMAN" logo are
by turning the equipment off and on, the user is
registered trademarks of Sony Corporation.
encouraged to try to correct the interference by
ˎ© 2013 CSR plc and its group companies. The
one or more of the following measures:
aptX® mark and the aptX logo are trade marks
 Reorient or relocate the receiving antenna.
of CSR plc or one of its group companies and
 Increase the separation between the
may be registered in one or more jurisdictions.
equipment and receiver.
ˎApple, the Apple logo, iPad, iPhone, iPod,
 Connect the equipment into an outlet on a
iPod classic, iPod nano and iPod touch are
circuit different from that to which the receiver
trademarks of Apple Inc., registered in the U.S.
is connected.
and other countries. App Store is a service mark
 Consult the dealer or an experienced radio/TV
of Apple Inc.
technician for help.
ˎ"Made for iPod" and "Made for iPhone"
mean that an electronic accessory has been
CAUTION
designed to connect specifically to iPod and
You are cautioned that any changes or
iPhone, respectively, and has been certified
modifications not expressly approved in this
by the developer to meet Apple performance
manual could void your authority to operate this
standards. Apple is not responsible for the
equipment.
operation of this device or its compliance with
Properly shielded and grounded cables and
safety and regulatory standards. Please note
connectors must be used for connection to host
that the use of this accessory with iPod, iPhone
computers and / or peripherals in order to meet
or iPad may affect wireless performance.
FCC emission limits.
ˎ"Xperia" and "Xperia Tablet" are trademarks of
This device complies with Part 15 of the FCC
Sony Mobile Communications AB.
Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This equipment must not be co-located or
operated in conjunction with any other antenna
or transmitter.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency
(RF) Exposure Guidelines. This equipment has
very low levels of RF energy that it deemed to
comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should
be installed and operated keeping the radiator
at least 20 cm or more away from person's body
(excluding extremities: hands, wrists, feet and
ankles).
This device complies with industry Canada
licence-exempt RSS standard(S).
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
This equipment complies with IC radiation
exposure limits set forth for an uncontrolled
environment and meets RSS-102 of the IC radio
frequency (RF) Exposure rules. This equipment
has very low levels of RF energy that it deemed
to comply without maximum permissive
exposure evaluation (MPE). But it is desirable
that it should be installed and operated keeping
the radiator at least 20 cm or more away from
person's body (excluding extremities:hands,
wrists, feet and ankles).
Before operating this system
Malfunctions that occur during the normal
use of the system will be repaired by Sony in
accordance with the conditions defined in the
limited warranty for this system. However, Sony
will not be liable for any consequences arising
from a failure to play caused by a damaged or
malfunctioning system.
Music discs encoded with copyright
protection technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware
that among those discs, there are some that do
not conform to the CD standard and may not be
playable by this product.
Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side
with digital audio material on the other side.
However, since the audio material side does
not conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
License and Trademark Notice
ˎWindows Media is either a registered trademark
or trademark of Microsoft Corporation in the
United States and/or other countries.
ˎThis product is protected by certain intellectual
property rights of Microsoft Corporation. Use or
distribution of such technology outside of this
product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary.
ˎMPEG Layer-3 audio coding technology and
patents licensed from Fraunhofer IIS and
Thomson.
Getting Started
Location of Controls
Note
This manual mainly explains operations using the remote, but the same operations can also be
performed using the buttons on the unit having the same or similar names.
Remote Unit (front/top)
Top
Front
When you use the remote for the first time
The battery is factory-installed in the remote.
Before using the remote for the first time,
remove the insulation sheet attached to the
battery holder. For details, see "Changing the
About operating with MENU  battery".
If MENU  is pressed twice, the operation
is canceled.
Unit (back)
 (USB) port
Setting the clock
Connect a USB device.
Note 1 Press  
to turn on the system.
ˎYou can use your iPhone/iPod with this system via
2
Press TIMER  .
Bluetooth or connection only.
If "PLAY SET" is displayed, press /  to
 AUDIO IN (external input) jack

select "CLOCK," then press .
Connect optional external equipment with an 3 Press /  
to set the hour, then press .
audio connecting cable (not supplied).
4
Press /  to set the minutes, then press
 .
 ~ AC IN input
Note
Connect the power cord (supplied) to the wall
ˎThe clock settings are reset when you disconnect the
outlet.
power cord or if a power failure occurs.
 FM ANTENNA
To display the clock when the system is off
Press DISPLAY  repeatedly to display the clock.
Connect the FM antenna.
The clock is displayed for about 8 seconds.
Note
If the system is in BLUETOOTH Standby mode,
ˎFind a location and an orientation that provide good
the clock does not appear by pressing DISPLAY
reception, and then fix the antennas to a stable surface
.
(window, wall, etc.).
ˎSecure the end of the FM lead antenna with adhesive
tape.
ˎCompatibility with all MP3 encoding/writing software,
Listening to a CD
CD-R/RW drive and recording media cannot be
guaranteed. Incompatible MP3 discs may produce noise or
interrupted audio or may not play at all.
Playing a CD-DA/MP3 disc
Creating your own program
1
Press FUNCTION  to select "CD."
(Program Play)
2 Insert a CD to the disc slot  at the top of the
unit. Plays the programmed track or file in a CD.
Load a CD with the label side (printed side) 1 Select "PROGRAM" in step 5 of "To change the
toward you. .
play mode" , then press
2
When using an MP3 disc, press +/–  to
Label side
select the folder containing the tracks or files
(printed side)
that you want to program.
If you want to play all tracks or files in the
folder, press .
3
Press /  to select a desired track or
file, then select .
 (eject) 
Plays back automatically. If you switch the
Selected track Total playing time
function to "CD" from another function when
or file number of the selected
a CD is already inserted in the slot, press 
track or file
 after "READING" has disappeared from the
display window .
Repeat the steps above to program additional
The button of the remote or the unit enables
tracks or files.
you to fast-rewind/fast forward, select a track,
4  
Press .
file or folder (for MP3 disc), etc.
Your program of tracks or files starts playback.
To eject the CD
To cancel program play
Press  (eject)  on the unit.
In step 1, select "NORMAL" for "PROGRAM," then
Note .
press
ˎ8 cm CD cannot be used with this system.
ˎDo not load a CD with non-standard shapes (e.g., heart,
To delete a programmed track or file
square, star). Doing this may cause irreparable damage to
Press CLEAR  while the play is stopped. Each
the system.
time you press the button, the last programmed
ˎDo not use a CD with tape, stickers or paste on it as this
may cause malfunction. track or file will be deleted.
ˎWhen you remove a CD, do not touch the surface of the
When all the programmed tracks or files are
disc.
deleted, "NO STEP" appears.
To change the play mode Tip
ˎUp to 25 tracks or files can be programmed. If you attempt
Play mode enables you to playback the same
to program more than 25 tracks or files, "FULL" will be
music repeatedly or shuffle-play.
displayed. In this case, delete unnecessary tracks.
ˎTo play the same program again, press  .
Play mode
Note
ˎWhen the disc is ejected or the power cord is
disconnected after programming, all the programmed
tracks and files are deleted.
1
Press   to stop playback.
If you select "REPEAT" in step 4, you do not
have to stop playback.
Listening to the radio
2
Press MENU .
3 Press /  to select "CD MENU", then press
.
Tuning in a radio station
4 Press /  to select "PLAYMODE" or
.
"REPEAT," then press
1 Press FUNCTION  to select "FM".
5
Press /  to select the play mode, then
2
Press and hold PRESET +/–  until the
press .
frequency indication in the display window 
You can select the following play modes. starts changing, then release the button.
Tuning stops automatically when a FM stereo
PLAYMODE
broadcast is received (Automatic Scanning).
"ST" lights up in the display window .
Play mode Effect
NORMAL Plays a track or file.
Manual tuning
FOLDER* Plays all tracks in the selected
Press PRESET +/–  repeatedly to tune-in the
folder. "FLDR" lights up in the
desired station.
display window .
Tip
SHUFFLE Plays all tracks or files in
ˎIf reception of an FM stereo broadcast is noisy, press MENU
random order. "SHUF" lights

and select "TUNE:MENU," "FM MODE" and "MONO" in
up in the display window .
turn, to select monaural reception. This reduces noise.
FLDR.SHUF* Plays all tracks or files in the
selected folder in random
order. "FLDR. SHUF" lights up
Presetting radio stations
in the display window .
PROGRAM Plays the programmed tracks
You can preset your desired radio stations.
or files. "PGM" lights
1
Tune in the desired station, then press MENU
up in the display window .
.
For details, see "Creating your
2 Press /  to select "TUNE:MENU," then
own program (Program Play)".
.
press
* This play mode is applicable only for playing an MP3 disc.
3
Press /  to select "MEMORY," then press
.
REPEAT
4 Press /  to select "OK," then press .
Play mode Effect
5 Press /  to select the preset number,
ALL (Repeat The system plays all tracks in a
.
then press
plays all tracks) disc or folder repeatedly.
Preset number
" " lights up in the display
window .
ONE (Repeat The system plays the selected
plays one track) track repeatedly. " 1" lights
"COMPLETE" appears in the display window
up in the display window .
 and the radio station is registered with the
OFF Cancels repeat playback.
preset number.
Repeat the steps above to register further
Note on playing MP3 discs
radio stations.
ˎDo not save unnecessary folders or files on a disc that has
MP3 files. 6 Press /  to turn off the power, then press
ˎFolders that have no MP3 files are not recognized on the
/  again to turn on the power.
system.
ˎThe system can only play MP3 files that have a file
Tip
extension of ".mp3."
ˎYou can preset up to 20 FM stations.
Even when file name has the ".mp3" file extension, if it is
ˎIf you select an already-registered preset number in step
not an audio MP3 file, playing this file may generate a loud
5, the preset radio station is replaced by the currently
noise, which could cause damage of the system.
tuned-in radio station.
ˎThe maximum number of MP3 folders and files compatible
with this system is:
To tune in to a preset radio station
 999* folders (including the root folder)
 999 files Press PRESET +/–  to select the preset number
 250 files in a single folder
to which the desired station is registered.
 8 folder levels (in the tree structure of files)
* This include folders that have no MP3 or other files. The
number of folders that the system can recognize may
be less than actual number of folders, depending on the
folder structure.
Listening to a file on a USB Listening to music through
device a BLUETOOTH connection
Playing a file on a USB device Pairing the system with a
BLUETOOTH device and listening
You can play audio files stored on a USB device
such as WALKMAN® or digital media player, on
to music
this system by connecting a USB device to the
system.
You can listen to music from BLUETOOTH device
For details on compatible USB devices, see over a wireless connection.
"Compatible devices and versions." Before using the BLUETOOTH function, perform
1 pairing to register your BLUETOOTH device.
Press FUNCTION  to select "USB."
Note
2 Connect the USB device to the (USB) port
ˎPlace the BLUETOOTH device to be connected within one
 on the rear of the unit.
meter of the system.
Connect the USB device directly, or via the USB ˎIf your BLUETOOTH device is compliant with touch (NFC),
cable supplied with the USB device, to the skip the next procedure. See "Listening to music by one-
(USB) port . touch action (NFC)."
1
Wait until "READING" disappears. Press FUNCTION  to select "BT AUDIO."
3
Press  . 2 Press MENU .
Starts playback.
3
Press /  to select "BT MENU," then press
You can operate fast-rewind/fast-forward,
.
selecting a track or file or selecting folder with
4 Press /  to select "PAIRING," then press
the remote or the button of the unit.
.
5 Press /  to select "OK" then press .
To change the play mode
When "PAIRING" starts flashing in the display
When playing the USB device, the play mode
window , the system changes to pairing
can be selected. Press MENU , then select
mode.
"USB MENU." Select "PLAYMODE" or "REPEAT."
For details, see "To change the play mode" of 6
Search for this system with the BLUETOOTH
"Listening to a CD." When a file on a USB device
device.
is playing, programmed playback cannot be
A list of the devices found may appear on the
played.
BLUETOOTH device display.
Tip 7
Select [SONY:CMT-X5CD] (this system).
ˎIf a USB device is connected to the unit, battery charging
If prompted to enter a passkey on the
starts automatically. Even when the system is off, the USB
device can be charged. BLUETOOTH device, enter "0000."
ˎIf the USB device cannot be charged, disconnect and
If this system is not shown in the display of
reconnect it. For details on the charging status of the USB
the device, proceed from step 1 again.
device, see the operating manual of the USB device.
When pairing is completed, the display
Note
changes to the connected BLUETOOTH device
ˎThe playback order for the system may differ from the
name from "PAIRING" and the BLUETOOTH
playback order of the connected digital music player.
indicator lights up.
ˎBe sure to turn off the system before removing the USB
device. Removing the USB device while the system is
8 Press  .
turned on may corrupt the data on the USB device.
ˎWhen USB cable connection is necessary, connect the Starts playback.
USB cable supplied with the USB device to be connected.
Depending on the BLUETOOTH device, press
For details on connection, refer to the operation manual
  again. Also, you may have to start up a
supplied with the USB device to be connected.
ˎIt may take time before "READING" appears after music player on the BLUETOOTH device.
connecting, depending on the type of USB device
9 Press VOL +/–  to adjust the volume.
connected.
ˎDo not connect the USB device through a USB hub. If the volume cannot be changed on the
ˎWhen the USB device is connected, the system reads all
system, adjust it on your BLUETOOTH device.
the files on the USB device. If there are many folders or
Operation such as fast-rewind/fast-forward,
files on the USB device, it may take a long time to finish
reading the USB device. selecting music and selecting a folder can be
ˎWith some connected USB devices, it may take a long time operated with the remote or buttons of the
to transmit signals from the system or to finish reading the
unit.
USB device.
ˎCompatibility with all encoding/writing software cannot
Tip
be guaranteed. If audio files on the USB device were
ˎYou can perform a pairing operation or attempt to make a
originally encoded with incompatible software, those files
BLUETOOTH connection with another BLUETOOTH device
may produce noise or, may malfunction.
while the BLUETOOTH connection is established with one
ˎThe maximum number of folders and files on the USB
BLUETOOTH device. The currently established BLUETOOTH
device compatible with this system is: connection is canceled when BLUETOOTH connection with
 1,000* folders (including the root folder)
another device is successfully established.
 3,000 files
Note
 250 files in a single folder
ˎThe operations described above may not be available
 8 folder levels (in the tree structure of files)
for certain BLUETOOTH devices. In addition, the actual
* This includes folders that have no playable audio file and
operations may differ depending on the connected
empty folders. The number of folders that the system
BLUETOOTH device.
can recognize may be less than actual number of folders,
ˎOnce a pairing operation is performed, it does not have
depending on the folder structure.
to be performed again. In the following cases, however, a
ˎThe system does not necessarily support all the functions pairing operation must be performed again:
provided in a connected USB device.
 Pairing information was erased when the BLUETOOTH
ˎFolders that have no audio files are not recognized.
device was repaired.
ˎThe audio formats that you can listen to with this system  You attempt to pair the system with more than 10
are as follows:
BLUETOOTH devices.
 MP3: file extension ".mp3"
This system can pair with up to 9 BLUETOOTH devices.
 WMA*: file extension ".wma" If you pair another BLUETOOTH device after pairing
 AAC*: file extension ".m4a," "mp4" or ".3gp" with 9 devices was performed, pairing information of
the device that was connected with the system first is
Note that even when file name has the correct file
overwritten with that of the new device.
extension, if the actual file differs, the system may
 Pairing registration information of this system is erased
produce noise or may malfunction.
from the connected device.
* Files with DRM (Digital Rights Management) copyright  If you initialize the system or erase the pairing history
protection or files downloaded from an online music with the system, all the pairing information will be
store cannot be played on this system. If you try to play erased.
one of these files, the system plays the next unprotected ˎThe sound of this system cannot be sent to a BLUETOOTH
audio file. speaker.
ˎ"Passkey" may be called "Passcode," "PIN code," "PIN
number" or "Password," etc.
Listening to music with
To check the address of a connected
optional audio components BLUETOOTH device
Press DISPLAY , while the name set on the
connected BLUETOOTH device is shown in the
display window . The BLUETOOTH device
Playing back the music of
address appears in two lines on the system
display window  for 8 seconds.
optional audio components
To cancel the connection with a
You can play a track of optional audio
BLUETOOTH device
components connected to the unit.
Disconnect the BLUETOOTH connection on the
Note
ˎBeforehand, press the VOL –  to turn down the volume. BLUETOOTH device. "BT AUDIO" appears in the
display window .
1 Press FUNCTION  to select "AUDIO IN."
2
Connect its audio connecting cord to the
To erase the pairing registration
AUDIO IN jack  on the rear of the unit and
information
the output terminal of the optional external
equipment.
1
Select "DEL LINK" after step 3 on "Pairing
3 the system with a BLUETOOTH device and
Start playback of the connected component.
listening to music," then press .
Adjust the volume on the connected
component during playback. 2 Press  /   to select "OK," then press .
4 Press VOL +/  on the remote to adjust the "COMPLETE" appears in the display window
 and all the pairing information is erased.
volume.
Note
Note
ˎThe system may enter Standby mode automatically if the ˎIf you have erased the pairing information, you cannot
make a BLUETOOTH connection unless pairing is
volume level of the connected component is too low. For
performed again.
details, see "Setting the Automatic Standby function."