Panasonic SF2B Series Instruction Manual page 12

<Display section>
Emitter
Beam-axis alignment indicator
[RECEPTION]
Operation indicator [OSSD]
Emission halt indicator [HALT]
Fault indicator [FAULT]
Setting indicator [SETTING]
Description
<Wiring synchronization using 8-core cable>
When device top receives light: lights up in red
When device top end receives light: blinks in red
A
When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
<Wiring synchronization using 8-core cable>
When device upper middle receives light: lights up in red
B When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Beam-axis align-
Always OFF
ment indicator
(Red / Green)
<Wiring synchronization using 8-core cable>
[RECEPTION]
When device lower middle receives light: lights up in red
C When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
<Wiring synchronization using 8-core cable>
When device bottom receives light: lights up in red
When device bottom end receives light: blinks in red
D
When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
<Wiring synchronization using 8-core cable>
When control output (OSSD 1 / 2) is OFF: lights up in red
Operator indicator
When control output (OSSD 1 / 2) is ON: lights up in green
(Red / Green) [OSSD]
<Beam synchronization using 4-core cable>
(Note 1)
When an error occurs in emitter: lights up in red
When emitter operates normally: lights up in green
Emission halt indicator When light emission is halt: lights up
(Orange) [HALT] When light is emitted: turns OFF
Fault indicator When fault occurs in the device:
(Yellow) [FAULT]
<Wiring synchronization using 8-core cable>
Always OFF
Setting indicator
<Beam synchronization using 4-core cable>
(Red) [SETTING]
When frequency 1 is set: One bar lights up
When frequency 2 is set: Two bars light up
Notes: 1) Since the color of the operation indicator changes according to ON / OFF status of the control output
(OSSD 1 / 2), the operation indicator is marked as "OSSD" on the device.
2) The threshold where the control output (OSSD 1 / 2) changes from OFF to ON is applied as "100%
incident light intensity".
3) "When light is blocked" refers to the status that there exists any object blocking light in the sensing area.
4) The description given in [ ] is marked on the device.
12
Ramco Innovations | www.ramcoi.com | 800-328-6236 | nsales@ramcoi.com
Top end
Beam-axis
alignment
indicator
[RECEPTION]
Bottom end
Function
Beam-axis align-
ment indicator
(Red / Green)
[RECEPTION]
OSSD indicator
(Red / Green) [OSSD]
Incident light inten-
sity indicator
(Orange / Green)
[STB.]
lights up or blinks Fault indicator
(Yellow) [FAULT]
Digital error indicator
(Red)
© Panasonic Industrial Devices SUNX Co., Ltd. 2016
Receiver
Beam-axis alignment indicator
[RECEPTION]
OSSD indicator [OSSD]
Incident light intensity indicator [STB.]
Fault indicator [FAULT]
Digital error indicator
Description
<Wiring synchronization using 8-core cable>
When device top receives light: lights up in red
When device top end receives light: blinks in red
A
When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
<Wiring synchronization using 8-core cable>
When device upper middle receives light: lights up in red
B When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
<Wiring synchronization using 8-core cable>
When device lower middle receives light: lights up in red
C When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
<Wiring synchronization using 8-core cable>
When device bottom receives light: lights up in red
When device bottom end receives light: blinks in red
D
When control output (OSSD 1 / 2) is ON: lights up in green
<Beam synchronization using 4-core cable>
Always OFF
When control output (OSSD 1 / 2) is OFF: lights up in red
When control output (OSSD 1 / 2) is ON: lights up in green
When sufficient light is received (incident light:
130% or more) (Note 2): lights up in green
When light is stably received (incident
light: 115 to 130%) (Note 2): OFF
When light is unstably received (incident light:
100 to 115%) (Note 2): lights up in orange
When light is blocked: OFF (Note 3)
When fault occurs in the device:
<Wiring synchronization using 8-core cable>
When device goes into lockout condition,
error contents are indicated.
<Beam synchronization using 4-core cable>
When device goes into lockout condition,
error contents are indicated.
When frequency 1 is set: The middle bar lights up
When frequency 2 is set:
The middle bar and the bottom bar light up
Function
lights up or blinks