Mitsubishi Electric 800 Series Instruction Manual page 44

Description
*4
Address
Upper 8 bits
Link parameter
RWwn+2
extended setting
RWwn+3 Data to be written
RWwn+4 Monitor code 3
RWwn+5 Monitor code 4
RWwn+6 Monitor code 5
RWwn+7 Monitor code 6
RWwn+8 Fault record No.
RWwn+9
PID set point (0.01% increments)
RWwn+A
PID measured value (0.01% increments)
RWwn+B
PID deviation (0.01% increments)
RWwn+C Torque command or torque limit
RWwn+D H00 (Free)
RWwn+E H00 (Free)
RWwn+F H00 (Free)
Link parameter
RWwn+10
extended setting
RWwn+11 Data to be written
Link parameter
RWwn+12
extended setting
RWwn+13 Data to be written
Link parameter
RWwn+14
extended setting
RWwn+15 Data to be written
Link parameter
RWwn+16
extended setting
RWwn+17 Data to be written
Link parameter
RWwn+18
extended setting
RWwn+19 Data to be written
RWwn+1A
RWwn+1B
RWwn+1C
H00 (Free)
RWwn+1D
RWwn+1E
RWwn+1F
*1 When Pr.128 = "50, 51, 60, or 61", the register is valid. When Pr.128 = "1000 to 2011", the register is valid depending on the setting in Pr.609 or
Pr.610.
*2 The display can be changed to rotations per minute (machine speed) using Pr.37 and Pr.53.
*3 When the output frequency or the set frequency is selected as the monitor item, rotations per minute (machine speed) can be displayed using
Pr.37 and setting "4" in Pr.53.
*4 "n" indicates a value determined by the station number.
 Details of the I/O signals
The device numbers described in this section are for the station number 1. For the station number 2 and later, the device
numbers are different. (Refer to the manual for the CC-Link master module for the correspondence between device numbers
and station numbers.)
Refer to
page
Lower 8 bits
Instruction code 46
46
46
46
46
46
H00 46
*1
46
*1
46
*1
46
46, 52
—
Instruction code 46
46
Instruction code 46
46
Instruction code 46
46
Instruction code 46
46
Instruction code 46
46
—
Description
*4
Address
Upper 8 bits
RWrn+2 Reply code 2
RWrn+3 Data to be read
RWrn+4
Third monitor value
RWrn+5
Fourth monitor value
RWrn+6
Fifth monitor value
RWrn+7
Sixth monitor value
RWrn+8 Fault record No.
RWrn+9 Fault record (output frequency)
RWrn+A Fault record (output current)
RWrn+B Fault record (output voltage)
RWrn+C Fault record (energization time)
RWrn+D
RWrn+E H00 (Free)
RWrn+F
RWrn+10 Reply code
RWrn+11 Data to be read
RWrn+12 Reply code
RWrn+13 Data to be read
RWrn+14 Reply code
RWrn+15 Data to be read
RWrn+16 Reply code
RWrn+17 Data to be read
RWrn+18 Reply code
RWrn+19 Data to be read
RWrn+1A
RWrn+1B
RWrn+1C
H00 (Free)
RWrn+1D
RWrn+1E
RWrn+1F
2.6 CC-Link IE Field Network Basic
Refer to
page
Lower 8 bits
Reply code 1 47
47
*3
47
*3
47
*3
47
*3
47
Fault record (fault
47
data)
47
47
47
47
—
47
47
47
47
47
47
47
47
47
47
—
2. Ethernet Communication
1
2
3
4
5
6
7
8
9
10
43