Error Log Menu - Sony 5500 Operation Manual

Item number Display
2D INVALID SDI DATA
34 NO CASSETTE COMPARTMENT
MODE
3B NO LTC REPRODUCED
52 NO SUPPORTED PB FORMAT
53 SYSTEM MISMATCH
55 VIDEO PLL UNLOCKED
59 INPUT AUDIO DATA MISMATCH
32.000K
5A INPUT AUDIO DATA MISMATCH
47.056K
61 TELEFILE MEMORY IS FULL
62 NO AREA FOR TELEFILE DATA
ADDITION
63 INVALID FORMAT TELEFILE
64 TELEFILE DATA WRITE FAIL
65 NO TELEFILE LABEL
66 TELEFILE DATA WRITE IS
INHIBITED
67 TELEFILE DATA READ FAIL
71 INVALID FORMAT CONVERSION
72 REC/EDIT DISABLE CASSETTE
FORMAT
73 NO REFERENCE INFORMATION
74 ASYNCHRONOUS VIDEO INPUT
77 AUTO CUEUP ABORT

Error Log Menu

The time and time codes of errors and warnings occurring
during operation can be displayed in a list form in the
display. (Maximum listing is 99 items.)
Meaning
SDI input signal data is invalid.
The cassette compartment does not operate because the VTR is in
"no cassette compartment" mode.
LTC signal not detected on the tape.
The recording format cannot be played back by this unit.
The tape cannot be played with the current system settings.
Video lock generator PLL not locked to the video reference signal.
The input audio frequency is wrong.
The input audio frequency is wrong.
The remaining capacity of the Tele-File is low, and therefore the
next recording will overwrite old data.
There is no space at all in the Tele-File.
Parts of the Tele-File format are wrong.
A write to Tele-File error occurred.
The Tele-File could not be recognized, and therefore the cassette is
ejected (HDCAM-SR only).
Recording or editing was started with the Tele-File in overall write
inhibit mode.
A Tele-File read error occurred.
The settings do not allow format conversion.
The inserted cassette cannot be recorded or edited because of
system settings (recording format, system line, etc). This display
applies only to HDCAM/HDCAM-SR cassettes (SRW-5500 only).
Cannot lock because there is no 30 frames/second reference
information in 720/59.94p HD SDI input signals.
When external sync is selected, the external sync signal and the
HD SDI INPUT signal are more than ±5H out of phase.
Auto cue-up was aborted because the target cue-up time code is 1
second or more away from the current time code.
To open the error log menu
Press the SFT button (see page 19) and the DIAG button
(see page 18), then press the [F2] (ERR LOG) button.
P A G E
E R R O R L O G ' 0 3 / 0 6 / 0 2 1 0 : 2 7 : 2 8
T O P
T O T A L 9 9
P A G E
E N D
9 5 . 0 0 : 0 0 : 0 0 : 0 0 ( W ) 1 B
N O A 5 / A 6 I N P U T
F U L L
9 6 . 0 0 : 0 0 : 0 0 : 0 0 ( W ) 1 C
M S G
N O A 7 / A 8 I N P U T
9 7 . 0 0 : 0 0 : 0 0 : 0 0 ( W ) 1 D
A L L
N O A 9 / A 1 0 I N P U T
C L E A R
9 5 . 0 0 : 0 0 : 0 0 : 0 0 ( W ) 1 E
N O A 1 1 / A 1 2 I N P U T
W A R N I - E R R O R C O N D I -
T I M E
N G T I O N
o n o n o n
T C
E X I T
Error Messages and Warning Messages
137