Honeywell 7847i-E Installation And Setup Manual page 18

7847i-E Installation and Setup Guide
PROMPTS
Zn6 Trigger Type
30
(V+)_
Invert Zn6 Y/N
31
(N)_
Restore Zn6 Y/N
32
(Y)_
Delay Zn6 (secs)
33
(00)_
Enable Zn7 Y/N
34
(N)_
Zn7 Trigger Type
35
(V)_
Invert Zn7 Y/N
36
(N)_
Restore Zn7 Y/N
37
(Y)_
Delay Zn7 (secs)
38
(00)_
Use DHCP Y/N
39
(Y)_
NIC IP Address:
40
255.255.255.255_
Subnet Mask:
49
255.255.255.255_
Gateway IP Addr:
41
255.255.255.255_
DNS Serv IP Addr:
42
255.255.255.255_
Review? Y/N
43
3-6
ENTRY OPTIONS
• (V+)
• (V–)
• (EOLR)
[Y], [N]
[Y], [N]
[01-15]
[00] = no delay
[Y], [N]
• (V+)
• (V–)
• (EOLR)
[Y], [N]
[Y], [N]
[01-15]
[00] = no delay
[Y], [N]
12 digit:
xxx.xxx.xxx.xxx
12 digit:
xxx.xxx.xxx.xxx
12 digit:
xxx.xxx.xxx.xxx
12 digit:
xxx.xxx.xxx.xxx
[Y] = review
[N] = exit
DESCRIPTION
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
UL: V+ must be set as inverted and V- as non-inverted
Inverts the alarm and normal states of the zone 6 trigger;
otherwise uses normal input signal.
Enables restore reporting for zone 6.
Defines the reporting delay in seconds for zone 6.
UL: Must be 00
Enables alarm reporting for zone 7.
If [N], skip to Prompt 47: "Use DHCP."
Selects the triggering method for this zone input.
Press the [space] key to scroll choices.
UL: V+ must be set as inverted and V- as non-inverted
Inverts the alarm and normal states of the zone 7 trigger;
otherwise, uses normal input signal.
Enables restore reporting for zone 7.
Defines the reporting delay in seconds for zone 7.
UL: Must be 00
Dynamically allocates the IP addresses (recommended);
then skip to Prompt 43: "Review?"
If [N], uses fixed IP addresses.
Enter the 4-part address for this device. The four parts of
the address must be separated by spaces (displayed as
periods in Review mode).
Enter the 32-bit address mask used to indicate the portion
(bits) of the IP address that is being used for the subnet
address. The four parts of the address must be separated
by spaces (displayed as periods in Review mode).
Enter the 4-part address assigned to the Gateway. The
four parts of the address must be separated by spaces
(displayed as periods in Review mode).
Enter the 4-part IP address assigned to the DNS (Domain
Name System) server. The four parts of the address must
be separated by spaces (displayed as periods in Review
mode).
Reviewing Programming Mode Entries
To review the programming options (to ensure that the
correct entries have been made), press [Y]. The
programming prompts are displayed again. Use the
up/down arrow keys to scroll through the program fields
without changing any of the values. If a value requires
change, simply type in the correct value. When the last
field is displayed, the "REVIEW?" prompt again appears.
To exit the programming mode, press [N] in response to
the "REVIEW?" prompt, and refer to Exiting Programming
Mode at the end of this section.