Table of Contents
Advertisement
[ IV Remote Controller ]
How to Set the Weekly Timer
1. On the Normal Operation screen, make sure that the weekly timer icon
is displayed.
2. Press the TIMER MENU button
screen (
2
). (Each press toggles between "Set Up" and "Monitor".)
3. Press the TIMER ON/OFF (SET DAY) button
advances the day, which appears in the area labeled
4. Press the
or
INITIAL SETTING button (
desired operation pattern number (1 through 6)
* (The remote-controller display on the previous page shows how the
display would appear if operation #1 for Sunday were set to the values
shown below.)
Setup Matrix
Op No.
Sunday
Monday
• 8:30
No. 1
• ON
• 23 °C (73 °F)
• 10:00
• 10:00
No. 2
• OFF
• OFF
...
No. 6
Note:
By selecting the day to "Sun Mon Tues Wed Thurs Fri Sat", the same action
can be carried out at the same time every day.
(Example: In Operation #2 above, the unit is scheduled to be turned off at
10:00 every day.)
Time setting
5
SUN
˚C
5. Press the Set Time button
11
* Time will first increment in one-minute intervals, then in ten-minute
intervals, and then in one-hour intervals.
6. Press the ON/OFF button
1
at
.
6
* Each press toggles through the following options:
No display (no setting) → "ON" → "OFF"
7. Press the Set Temperature button
* Each press:
No display (no setting) ↔ 5 (41) ↔ 6 (43) ↔ ... ↔ 89 (192) ↔ 90 (194)
↔ No display. (Available temperature range: The temperature display
range is between 5 °C (41 °F) and 90 °C (194 °F). The actual range
which the temperature can be controlled will vary according to the type
of the connected unit.)
8. To clear the current values for the selected operation, press and quickly
release the CHECK (CLEAR) button
* The displayed time setting will change to "―:―", and the ON/OFF and
temperature settings will disappear.
(To clear all weekly timer settings at once, hold down the CHECK
(CLEAR) button
10
for two seconds or more. The display will begin
flashing, indicating that all settings have been cleared.)
9. After making the appropriate settings in Steps 5, 6. and 7, press the
CIR.WATER
button
to save the values.
4
Note:
The changes will not be saved unless the Mode (BACK) button
before the CIR.WATER
button
If two or more different operation patterns have been scheduled for exactly the
same time, only the operation with the highest Operation No. will be carried
out.
10. Repeat Steps 3 through 9 as necessary to add more settings.
11. Press the Mode (BACK) button
procedure and return to the Normal Operation screen.
12. To activate the timer, press the TIMER ON/OFF button
"Timer Off" icon (
10
) disappears.
* If no timer settings have been made, the "Timer Off" icon will flash on the
screen.
HWE10060
, so that the "Set Up" appears on the
12
to set the day. Each press
9
3
.
or
) to select a
7
8
.
4
<Operation 1
...
settings for
Saturday
Sunday>
Start the unit at
8:30, with the
temperature set to
23 °C (73 °F).
• 10:00
• 10:00
<Operation 2
• OFF
• OFF
settings for every
day>
Turn off the unit at
10:00.
Selection operation (ON or OFF)
6
* Does not appear if actions are scheduled.
ON
Temperature setting
7
WEEKLY
* Does not appear if no
temperature changes are
scheduled.
to set the time (
5
).
to select the desired operation (ON or OFF),
to set the temperature (
7
).
3
10
once.
2
is pressed
is pressed.
4
2
to return to complete the setting
9
, so that the
How to View the Weekly Timer Settings
1
1. Make sure that "WEEKLY" is displayed (
2. Press the TIMER MENU button
(
).
8
3. Press the TIMER ON/OFF (SET DAY) button
4. Press the
or
the settings (
9
).
* Each press will advance the display to the next timer operation in order
of time.
5. To close the monitor display and return to the Normal Operation screen,
press the Mode (BACK) button
To Turn Off the Weekly Timer
Press the TIMER ON/OFF button
10
To Turn On the Weekly Timer
Press the TIMER ON/OFF button
disappears.
10
Using the Simple Timer
1. The simple timer can be set in any of the following three ways.
• Start time only
• Stop time only
• Start & stop times
2. The simple timer can be set to start and stop the unit only once each within
a 72-hour period.
The time setting can be made in one-hour increments.
Note:
*1 Weekly, Simple, and AUTO-off timers cannot be used concurrently.
*2 The simple timer will not operate when any of the following conditions is
met. The timer is disabled; the system is in error; a test run is in progress;
the remote controller is performing self-check or remote controller check;
or a function or the timer is being set. If the ON/OFF status and/or the
temperature setting is centrally controlled, their settings cannot be
changed according to the schedule that was set from the remote controller.
12
BACK
PAR-W21MAA
2
- 43 -
Time Settings
8
9
SUN
TIMER
ON
OFF
˚C
WEEKLY
1
).
12
so that "Monitor" appears on the screen
9
to select the desired day.
INITIAL SETTING (
or
) to toggle through
7
8
2
.
9
so that "Timer Off" appears at
TIME SUN
˚C
˚C
WEEKLY
9
so that the "Timer Off" icon (
TIME SUN
˚C
˚C
WEEKLY
The unit starts when the set time has elapsed.
The unit stops when the set time has elapsed.
The unit starts and stops at the respective
elapsed times.
Hr
ON
AFTER
SIMPLE
TEMP.
ON/OFF
MENU
ON/OFF
INITIAL SETTING
CIR.WATER
MONITOR/SET
DAY
CHECK
TEST
CLOCK
CLEAR
11
9
10
1
10
.
10
)
1
4
GB
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
