ABB TPU2000 Technical Manual page 5

TPU2000/2000R Modbus/Modbus Plus/ Modbus TCP/IP Automation Guide
Tables
Section 1 - Introduction
Table 1-1. Protocol Capabilities Listed by Product Type...........................................................................................2
Section 2 - Communication Card Identification and Physical Port Characteristics
Table 2-1. TPU2000 Communication Options...........................................................................................................6
Table 2-2. TPU2000 Communication Card Matrix for Unit 488MRXDZ-CSSSQ ......................................................7
Table 2-3. TPU2000R Communication Options ........................................................................................................7
Table 2-4. TPU2000R Communication Card Matrix for Unit 588XXXYZ-XXXXQ ....................................................8
Table 2-5. TPU2000R Communication Card Matrix.................................................................................................8
Section 3 - TPU2000 and TPU2000R Device Connectivity
Table 3-1. Physical Interface Options......................................................................................................................10
Table 3-2. TPU2000 AUX COM Signal Assignments..............................................................................................16
Section 4 - TPU2000 and TPU2000R Device Parameterization
Table 4-1. TPU2000 and TPU2000R COM Port 0 Front Panel Interface Parameters............................................17
Table 4-2. WinECP Communication Port Settings ..................................................................................................19
Table 4-3. COM Port 1 and COM Port 2 WinECP Port Setting Options .................................................................19
Table 4-4. Valid Parameter Selection for Standard Ten Byte and Modbus Protocols ............................................22
Section 5 - Modbus
Table 5-1. Logical Output Modbus Address Map Definition ....................................................................................41
Table 5-2. Physical Output Contact Mapping Defined ............................................................................................50
Table 5-3. Momentary Change Detect Data Definition............................................................................................50
Table 5-4. Modbus Physical Output Momentary Change Detect Address Allocation .............................................54
Table 5-5. Logical Input Modbus Address Map Definition.......................................................................................57
Table 5-6. Physical Input Modbus Address Map Definition.....................................................................................59
Table 5-7. Logical Input Status Momentary Change Detect Status ........................................................................59
Table 5-8. Physical Input Momentary Change Detect Register Map ......................................................................63
Table 5-9. Register Scaling Queries........................................................................................................................69
Table 5-10. Minimum and Maximum Ranges for Scaled Numbers Depending Upon Scale Option and
Bit Length Selected .....................................................................................................................................71
Table 5-11. Default Scaling and Remapping Register Assignments ......................................................................75
Table 5-12. Relay Status Modbus Address Map Definition.....................................................................................78
Table 5-13. Diagnostic Status Modbus Address Map Definition .............................................................................80
Table 5-14. Unit Information Status Modbus Address Map Definition ....................................................................81
Table 5-15. Quick Status Modbus Address Map Definition.....................................................................................82
Table 5-16. Power Fail Table Register Definition....................................................................................................82
Table 5-17. Fast Status Modbus Address Map Definition .......................................................................................83
Table 5-18. Communication Error Event Log ..........................................................................................................83
Table 5-19. TPU2000/TPU2000R Metering Values ................................................................................................84
Table 5-20. Demand Metering Modbus Address Map Definition ............................................................................85
Table 5-21. TPU2000/TPU2000R Metering Values ................................................................................................87
Table 5-22. To Be Named .......................................................................................................................................88
Table 5-23. Peak Demand Register Map for the TPU2000R and TPU2000...........................................................90
Table 5-24. Minimum Demand Register Map for the TPU2000R and TPU2000 ....................................................93
Table 5-25. Breaker Counter Definition Table.........................................................................................................96
Table 5-26. Logical Input Table (8 Registers 128 Elements) ..................................................................................97
Table 5-27. Logical Input Definition Table (8 Registers - 127 Elements) .............................................................100
Table 5-28. Physical Output Table (1 Register Defined).......................................................................................102
Table 5-29. Physical Input Table (1 Register Defined)..........................................................................................102
Table 5-30. Force Table Mapping .........................................................................................................................103
Table 5-31. Three Winding Logical Output Points.................................................................................................105
Table 5-32. Fault Record Data Assignment ..........................................................................................................109
Table 5-33. Differential 2 Winding Fault Record Register Definition.....................................................................110
v