Canon Finisher-AB1 Service Manual page 210

Contents
5.2.1.2 Periodically Replaced Parts in the Saddle Finisher........................................................ 5-2
5.2.2 Durables ..................................................................................................................... 5-2
5.2.2.1 Durables in the Finisher ...................................................................................................... 5-2
5.2.2.2 Durables in the Saddle Stitcher ......................................................................................... 5-3
5.2.3 Periodical Servicing .................................................................................................. 5-3
5.2.3.1 Scheduled Servicing for the Finisher ................................................................................ 5-3
5.2.3.2 Scheduled Servicing for the Saddle Stitcher ................................................................... 5-3
5.3 Adjustment .......................................................................................................... 5-4
5.3.1 Basic Adjustment ...................................................................................................... 5-4
5.3.1.1 Adjusting the Height............................................................................................................. 5-4
5.3.1.2 Adjusting the Horizontal Registration/Angle .................................................................... 5-7
5.3.1.3 Adjusting the Sensor Intensity ......................................................................................... 5-10
5.3.2 Adjustment at Time of Parts Replacement ......................................................... 5-11
5.3.2.1 Adjusting the Tray A/B Position ....................................................................................... 5-11
5.3.2.2 Adjusting the Angle of the Aligning Plate (orthogonal)................................................. 5-12
5.3.2.3 Adjusting the Stapler Position .......................................................................................... 5-13
5.3.2.4 Adjusting the Speed of the Swing Guide........................................................................ 5-14
5.3.2.5 Adjusting the Aligning Plate Width .................................................................................. 5-15
5.3.2.6 Adjusting the Transport Belt Position.............................................................................. 5-17
5.3.2.7 Adjusting the Stapling Position (rear 1-point) ................................................................ 5-19
5.3.2.8 Adjusting the Stapling Position (front 1-point) ............................................................... 5-21
5.3.2.9 Adjusting the Stapling Position (2-point) ........................................................................ 5-24
5.3.2.10 Adjusting the Delivery of Stapled Stacks (lower delivery) ......................................... 5-26
5.3.2.11 Adjusting the Delivery of Stapled Stacks (saddle delivery) ....................................... 5-29
5.3.2.12 Adjusting the Saddle Binding Position .......................................................................... 5-32
5.3.2.13 Adjusting the Saddle Folding Position .......................................................................... 5-34
5.3.2.14 Adjusting the Saddle Lead Edge Stopper Position..................................................... 5-36
5.3.2.15 Adjusting the Saddle Alignment Reference ................................................................. 5-36
5.3.2.16 Adjustment of EEPROM (IC107) on the Finisher Controller PCB After Replacement 5-
38
5.3.2.17 Bufferless mode 1 ............................................................................................................ 5-39
5.3.2.18 Bufferless mode 2 ............................................................................................................ 5-40
5.3.2.19 Assist stopper position adjustment................................................................................ 5-41
5.3.2.20 Staple inlet guide height adjustment ............................................................................. 5-42
5.3.2.21 Paddle height adjustment .............................................................................................. 5-44
5.3.2.22 Adjustment at poor tray stackability (when the upper curl occurs) ......................... 5-46
5.3.2.23 Adjustment at poor tray stackability (when the lower curl occurs) .......................... 5-47
5.3.2.24 Adjustment at poor tray stackability (run over when using thin paper) ................... 5-49
5.3.2.25 Tray stacking limit cancellation adjustment ................................................................. 5-50
5.3.2.26 Saddle staple alignment adjustment ............................................................................. 5-52
5.3.2.27 Saddle disengage roller position adjustment............................................................... 5-56
5.3.2.28 The amount of sending of a saddle disengage roller adjustment............................. 5-58
5.3.2.29 Saddle staple position adjustment................................................................................. 5-60
5.3.3 Other ......................................................................................................................... 5-63
5.3.3.1 Service Mode (by DIP switch)<Incerter>........................................................................ 5-63