Related Manuals for Evolution EVO180
Summary of Contents for Evolution EVO180
- Page 1 EVO180 / STEEL SAW 1 180mm (7”) TCT Steel Circular Saw Instruction Manual Read instructions before operating this tool. This Instruction Manual was originally written in (UK) English. www.evolutionsteel.com...
-
Page 2: Table Of Contents
® TABLE OF CONTENTS PAGE Original Instructions Introduction Guarantee Read instructions before operating this tool. Machine Specification Vibration Labels and Symbols Intended use of this Power Tool Prohibited use of this Power Tool SAFETY PRECAUTIONS Electrical Safety Outdoor Use General Power Tool Safety Instructions Additional Safety Instructions GETTING STARTED Unpacking... -
Page 3: Introduction
Evolutions the use of our merchandise or from any other website by entering your details and thus cause. Evolution Power Tools is not liable for any ensure prompt service if ever needed. We costs incurred on such goods or consequential sincerely thank you for selecting a product damages. -
Page 4: Machine Specification
® STEELSAW1 TECHNICAL SPECIFICATIONS Maximum Cutting Reach: Mild Steel Box Section (at 90 ) inches (mm): 2-1/4” (56) Mild Steel Box Section (at 45 ) inches (mm): 1-3/8” (35) Mild Steel Plate – Optimal cutting Thickness inches (mm): 1/4” (6) Mild Steel Box Section –... -
Page 5: Vibration
• Avoid using excessive physical effort on Evolution blades. Only use blades designed for any of the machines controls. use in this machine and/or those recommended •... -
Page 6: Prohibited Use Of This Power Tool
® PROHIBITED USE OF THIS POWER TOOL POWER TOOL GENERAL SAFETY INSTRUCTIONS WARNING: This product is a Steel cutting Hand Held circular Saw and must (These General Power Tool Safety Instructions only be used as such. It must not be modified in are as specified in BS En 60745-1:2009 &... - Page 7 EVO180 / STEEL SAW 1 e) When operating a power tool outdoors, use 4) General Power Tool Safety Warnings an extension cord suitable for outdoor use. [Power tool use and care]. Use of a cord suitable for outdoor use reduces the a) Do not force the power tool.
-
Page 8: Additional Safety Instructions
® HEALTH ADVICE c) Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade WARNING: When using this machine, teeth should be visible below the workpiece. dust particles may be produced. In some d) Never hold piece being cut in your hands instances, depending on the materials you are or across your leg. - Page 9 EVO180 / STEEL SAW 1 Kickback is the result of saw misuse and/or Further Safety Instructions incorrect operating procedures or conditions a) Check lower guard for proper closing and can be avoided by taking proper before each use. Do not operate the saw if precautions as given below.
-
Page 10: Getting Started Unpacking
Caution: This packaging contains sharp this machine the following accessories are also objects. Take care when unpacking. remove available from the Evolution online shop at the machine, together with the accessories www.elovutionpowertools.com or from your supplied from the packaging. check carefully local retailer. -
Page 11: Machine Overview
EVO180 / STEEL SAW 1 GETTING STARTED - MACHINE OVERVIEW 1. ON/OFF TRIGGER SWITCH 4. LOWER BLADE GUARD 2. AUXILIARY FRONT HANDLE 5. FITTED BLADE IN SITU 3. DISCHARGE EXHAUST PORT www.evolutionsteel.com... -
Page 12: Assembly And Preparation
Do not alter or modify the mains lead. INSTALLING/REMOVING A BLADE WARNING: Only use genuine Evolution blades which are designed for this machine. Ensure that the maximum speed of the blade is compatible with the machine. Only Fig. - Page 13 EVO180 / STEEL SAW 1 • Ensure that the direction of rotation arrows printed on the blade, match the direction of rotation arrow found on the chip collector. (Fig. 4) • Reinstall the outer drive flange and the arbor socket headed screw.
-
Page 14: Operating Instructions
® Adjustment of the Cutting Depth release the Lever Lock (Fig. 7) to adjust to the required cutting depth. In most cases the depth should be set at maximum unless there are obstructions below the work surface. Note: Always check to see if there are any obstructions below the work surface that could influence the setting of the cutting depth. - Page 15 EVO180 / STEEL SAW 1 Chip Collector This machine is fitted with a chip collector to capture metal chips. The chip collector cover plate is provided with a transparent ‘window’ so that the operator can see the contents and empty when necessary.
- Page 16 ® CUTTING ADVICE WARNING: If the motor should stop or stall whilst a cut is being attempted WARNING: The operator should wear release the trigger switch immediately and all relevant PPE (Personal Protection disconnect the machine from the power supply. Equipment) necessary for the job at hand.
-
Page 17: Maintenance
EVO180 / STEEL SAW 1 MAINTENANCE BRUSH CHECKING AND/OR REPLACEMENT WARNING: Any maintenance must be Disconnect the machine from the power supply. • carried out with the machine switched off • Place the machine on a level, secure surface. and disconnected from the mains/battery •... - Page 18 The manufacturer of the product covered by this Declaration is. Evolution Power Tools Ltd. Venture 0ne, Longacre close, Holbrook Industrial Estate, Sheffield S20 3Fr, Uk The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below.
-
Page 19: Service Parts Diagram
EVO180 / STEEL SAW 1 SERVICED PARTS LIST F11100 www.evolutionsteel.com...
Need help?
Do you have a question about the EVO180 and is the answer not in the manual?
Questions and answers