Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Axminster SIEG G1 Engineer Series
Summary of Contents for Axminster SIEG G1 Engineer Series
- Page 1 Code 200024 SIEG G1 Powered Hacksaw AT&M: 30/01/2015...
-
Page 2: Table Of Contents
Index of Contents Index of Contents Declaration of Conformity What’s in the Box General Instructions for 230v Machines 05-06 Specific Safety for the Powered Hacksaws Initial Assembly Instructions Specifications Illustration and Parts Description 09-10 Operation of the Powered Hacksaw Routine Maintenance Parts Breakdown/List 13-14-15 The symbols below advise that you follow... -
Page 3: Declaration Of Conformity
Declaration of Conformity Copied from CE Certificate The undersigned, Ole Stilling authorised by Shanghai SIEG Machinery Co., Ltd No. 555 Caofeng Rd, South to No.17 Bridge of Caoan Rd, Shanghai, P.R China declares that this product: Bench Cutter G1 manufactured by Shanghai SIEG Machinery Co. is in compliance with the following standards or standardisation documents in accordance with Council Directives 73/23/EEC 93/68/EEC 98/37/EC... -
Page 4: What's In The Box
What’s in the Box Quantity Item Part Model Number Bench Grinder G1 1No. Powered Hacksaw 1 No. Material Length Stop Kit 1 No. Saw Blade Tool set Comprising of: 1 No. 14-17mm Open Ended Spanner 1 No. 17-19mm Open Ended Spanner 1 No. - Page 5 Gerneral Instructions for 230V Machines Keep the work area as uncluttered as is practical, Good Working Practices/Safety this includes personnel as well as material. The following suggestions will enable you to observe Under no circumstances should CHILDREN be good working practices, keep yourself and fellow allowed in work areas.
-
Page 6: Specific Safety For The Powered Hacksaws
Gerneral Instructions for 230V Machines Do not work with cutting or boring tools of any there may be volatile gases. There are very expensive, description if you are tired, your attention is very specialised machines for working in these wandering or you are being subjected to areas, THIS IS NOT ONE OF THEM. -
Page 7: Initial Assembly Instructions
Please refer to the Assembly Drawing if you Services personnel straight away using the numbers experience difficulties, this will enable you to more listed in the Axminster catalogue. readily identify those parts of the machine to which we will be referring. -
Page 8: Specifications
Specifications Code 200024 Model SIEG G1 Rating Trade Power 250W Blade Length 300 x 25 x 1.2mm Stroke Rate 170/min Max Capacity Round 130mm Overall L x W x H 820 x 380 x 755mm Weight 68kg Vice shaft Clamp vice handle... -
Page 9: Illustration And Parts Description
Illustration and Parts Description Grease nipple Handle Saw blade Saw clamp screw Adjustable vice Gas strut Chassis Screw pin Material length stop assembly Depth stop... -
Page 10: Illustration And Parts Description
Illustration and Parts Description Grease nipple Stop actuator Motor Latching arm Scale NVR On/Off switch 0-45˚ Vice clamp... -
Page 11: Operation Of The Powered Hacksaw
Operation of the Powered Hacksaw This is a very simple machine to operate, there are no DO NOT lean on the arm to increase the cutting rate. choices of speeds or down-feed settings to select. Use the length stop assembly to create identical The arm has a supporting gas strut to take some of lengths of materials. -
Page 12: Routine Maintenance
Routine Maintenance WARNING! DISCONNECT YTHE MACHINE FROM THE MAINS SUPPLY. Excessive dust in the motor can cause excessive Every 2 hours of use, apply a general purpose grease heat to develop. Every effort should be made to to the arm slides via the grease nipples provided prevent foreign material from entering the motor. - Page 13 Parts Breakdown/List...
- Page 14 Parts Breakdown/List Description Q’ty Oil cup M8 Bolt M8×25 Box cover Washer 8 Nut M12 Spring washer 8 Washer 12 Motor 180W Bolt M8×25 Key 5×14 Saw blade 300×25×1.2 Motor gear Nut M8 Washer Spring washer 5 Tighten hand wheel Screw M5×20 Screw M8×20 Washer 10...
- Page 15 Parts Breakdown/List Fixed block Screw M5×8 Bolt M8×35 Washer 5 Screw Safety cover Long staff Side cover Board Label Bolt M8×50 Switch Machine base Screw M5×10 Movement block Switch support Screw M6×12 Lengthways screw Bolt M8×16 Pin 6×28 Washer 10 Handle sleeve Cushioning cylinder handgrip...
- Page 16 Hobby, Trade, Industrial, Engineer, Air Tool & CNC Technology Series machines It’s probably the most comprehensive FREE guarantee ever- buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! •...
Need help?
Do you have a question about the SIEG G1 Engineer Series and is the answer not in the manual?
Questions and answers