Femi NG 160 Instructions For Use And Maintenance Manual
  1. Manuals
  2. Brands
  3. Femi Manuals
  4. Saw
  5. NG 160
  6. Instructions for use and maintenance manual

Femi NG 160 Instructions For Use And Maintenance Manual

Band-saw machine
Hide thumbs Also See for NG 160:

Advertisement

Table of Contents

See also: Use and Maintenance Manual
SEGATRICE A NASTRO
BAND-SAW MACHINE
BANDSÄGEMASCHINE
SCIE A RUBAN
SIERRA DE CINTA
SERRA DE FITA
BANDZAAGMACHINE
Art.
NG 160
CERTIFICATA
CERTIFIED
GEPRÜFT
CERTIFIE
CERTIFICADA
CERTIFICADA
GECERTIFICEERD
ISTRUZIONI PER L’USO E MANUTENZIONE
INSTRUCTIONS FOR USE AND MAINTENANCE
GEBRAUCHSANLEITUNGEN UND WARTUNG
MODE D’EMPLOI ET ENTRETIEN
INSTRUCCIONES PARA EL USO Y MANUTENCION
INSTRUÇÕES DE UTILIZAÇÃO
GEBRUIK- EN ONDERHOUDSAANWIJZINGEN
www.femi.it

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NG 160 and is the answer not in the manual?

Questions and answers

Related Manuals for Femi NG 160

Summary of Contents for Femi NG 160

  • Page 1 SEGATRICE A NASTRO BAND-SAW MACHINE BANDSÄGEMASCHINE SCIE A RUBAN SIERRA DE CINTA SERRA DE FITA BANDZAAGMACHINE Art. NG 160 CERTIFICATA CERTIFIED GEPRÜFT CERTIFIE CERTIFICADA CERTIFICADA GECERTIFICEERD ISTRUZIONI PER L’USO E MANUTENZIONE INSTRUCTIONS FOR USE AND MAINTENANCE GEBRAUCHSANLEITUNGEN UND WARTUNG MODE D’EMPLOI ET ENTRETIEN INSTRUCCIONES PARA EL USO Y MANUTENCION INSTRUÇÕES DE UTILIZAÇÃO...
  • Page 2 ITALIANO (IT) ......................3 ÷ 8 ENGLISH (EN) ......................9 ÷ 14 DEUTSCH (DE) ....................... 15 ÷ 20 FRANCAIS (FR) ...................... 21 ÷ 26 ESPANOL (ES) ......................27 ÷ 32 PORTUGUÊS (PT) ....................33 ÷ 38 NEDERLANDS (NL) ....................39 ÷ 44...
  • Page 3 2006 2009 2007 2010 2008 2011...

  • Page 4: Introduction To Use

    INTRODUCTION TO USE ........9 INTRODUCTION TO USE 2 INSTALLATION ............10 Before starting work with your sawing machine, carefully read this instructions manual so that you are familiar with the machine and its uses and where it should not be used. 3 ADJUSTMENT ............

  • Page 5: Installation

    STANDARD SAFETY PROCEDURS DESCRIPTION OF THE MACHINE (Fig. 1) - Do not use the machine in very damp places or in the The belt sawing machine consists of two basic parts: the presence of inflammable liquids or gases. machine body 5 complete with motor and drive 7 which is - Do not use it in the open air when general weather and integrated into lower part, consisting of the clamp 11, the environmental conditions are unfavourable (eg.

  • Page 6: Electrical Connections

    POSITION/WORK STATION (Fig.3) CUTTING ANGLE (Fig.6) Place the machine on a sufficiently flat workbench so that To performe a cut at 45, slacken the two knobs M and the machine has the better possible stability. rotate the body to the left until it rest on stop N, whose In respect of ergonomic criteria during cutting operations, position was calibrated during the final inspection.

  • Page 7: Replacing The Blade (Fig. 9)

    After running-in, the same piece may easily be cut in REPLACING THE BLADE (Fig. 9) about 2 minutes. If the running-in process is done correctly, CAUTION: When you perform this operation, the finish and precision of the cut will be of better quality always wear protective gloves to avoid contact and the blade will last longer.

  • Page 8: Maintenance

    CORRECT POSITIONING OF THE PIECE IN FITTING THE BASE PLATE (Fig. 3) THE CLAMP (Fig. 11) (where included) The pieces to be cut should be fitted directly between the The fasten the machine to the base plate, use the four jaws without adding other objects.

  • Page 9: Troubleshooting

    TROUBLESHOOTING PROBLEMS PROBLEMS CAUSES SOLUTIONS SUGGESTED Defective motor, power cable or Specialized personnel should check the machine; do plug. not attempt to repair the motor by yourself. Blown electric panel fuses. Check fuse integrity and replace, if necessary. The motor does not work.

Table of Contents