Lopi Liberty Wood Stove Owner's Manual
  1. Manuals
  2. Brands
  3. Lopi Manuals
  4. Wood stove
  5. Liberty Wood Stove
  6. Owner's manual

Lopi Liberty Wood Stove Owner's Manual

Lopi liberty wood stove owner's manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

L i b e r t y
Wood Stove
Owner's Manual
Freestanding Stove
Mobile-Home Approved
Alcove Approved
Hearth-Stove Approved
Save these instructions
for future reference

SAFETY NOTICE:

7

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Liberty Wood Stove and is the answer not in the manual?

Questions and answers

Related Manuals for Lopi Liberty Wood Stove

Summary of Contents for Lopi Liberty Wood Stove

  • Page 1: Safety Notice

    L i b e r t y Wood Stove Owner's Manual Freestanding Stove Mobile-Home Approved Alcove Approved Hearth-Stove Approved Save these instructions for future reference SAFETY NOTICE:...
  • Page 2 Introduction Important Information Introduction Mail your Warranty Card Today, and Save Your Bill of Sale.
  • Page 3 General Information Stove Installation INSTALLATION DIAGRAMS Operating Your Appliance Table of Contents Maintaining Your Appliance Warranty Listing Information Optional Equipment Index...
  • Page 4 ASHES 36" Type Clay Liner...
  • Page 5 Mobile Home This Manual...
  • Page 6 21” Weight: 470 Lbs. 30” 6-1/4” The 6” diameter flue collar protrudes 1-1/4" above the stove top Height: Sculptured or Cast Legs...32-1/4" Pedestal...36-1/4" Note: Measure side, corner, and back clearances from the stove top. Measure front clearances from the stove face.
  • Page 9 Stove Installation Top View - Straight Installation Top View - Corner Installation (for qualified installers only) Figure 2 Figure 3...
  • Page 10 Mobile home installations must use the the reduced clearance connector clearances listed in this manual under “Additional Requirements for Mobile Home Installations”. Stove Clearance (as outlined in this manual) Minimum System 15' Maximum System 33'...
  • Page 11 When using outside air, find a location where the chimney and outside air hole do not interfere with structural members of the home. Pedestal (with insulation) directs air to the stove. Air may be drawn from a ventilated crawl space or use an air duct.
  • Page 12 Non-combustible alcove construction (on walls and ceiling) - see the explanation above. Ventilated air space 3 1/2" thick non- combustible material 1" Min. Non-combustible reinforcer...
  • Page 13 Rear heat shield Measure all clearances from the nearest edge of the stove top. 12” Min. Minimum Connector Clearance (as outlined above) Minimum Stove Clearance (as outlined above)
  • Page 14 Minimum Air Space to Combustibles (See Chimney Manufacturer's Instructions - usually 2") Minimum 15' Maximum 33' Stove Clearances (See the section "Stove Placement Requirements" for more details) Follow the chimney manufacturer's instructions and clearances for roof penetrations. A storm collar, flashing, and...
  • Page 15 Follow the chimney manufacturer's instructions and clearances for wall penetrations. A wall radiation shield (thimble) is required. Stove Clearances (See the section "Stove Optional Placement Requirements" insulated for more details) chase Cap and flashing prevents water from entering The liner must be stainless steel connector or flexible vent.
  • Page 16 (UBC, clearance etc.). Damage must be repaired to ceiling prior to installation. The chimney must be 15' to 33' tall. See the section "Stove Placement Requirements" for minimum clearances required. Chimney connector sections See the section "Floor Protection Requirements"...
  • Page 17 Rotate the door handle. 2 to 4 hours Swing the door open.
  • Page 18 Use the included pull tool to operate the bypass rod Bypass Pulled Out Used for starting and re-loading Bypass Pushed In Used for normal operation...
  • Page 20 Use the air control to change the burn rate. Low Burn High Burn (air control closed) (air control open) ASHES...
  • Page 21 CONTROL Creaks and Clicks: The 3/16" and 5/16" steel may creak or click when the stove heats up and cools down - this is normal. Blower Sounds: The blower will make a slight "humm" as it pushes air through the stove.
  • Page 22 Wood Cut wood to length and Store the wood off the ground in a chop into quarters. covered area. Allow for airflow around the wood to dry the wood. Air Flow Wood Leads Less More Heat Heat Leads More Smoke and Creostoe Air Flow Leads...
  • Page 24 ASHES Allow the stove to fully cool. Apply glass cleaner or soapy water to the inside of the glass. Wipe with newspaper or a paper towel. For Stubborn Creosote: Dip newspaper or a paper towel in cool ashes and wipe it on the glass. The ash...
  • Page 25 Exploded View Door Handle Washers Use a 9/16" Door Frame socket wrench to remove this nut. Use wood stove gasket cement to re-adhere loose gasket. Severely frayed or thread-bare gasket should be replaced. D oor Cam Adjustment: To tighten, remove...
  • Page 26 Touch-Up P a i n t BOTTOM OF Use a vacuum cleaner to remove any STOVE buildup on the screens of the blower.
  • Page 27 1/8” Hex Wrench # 20 Torx Driver NOTE: Place the glass gasket around the perimeter of the door retainer. NOTE: Glue the door gasket to the door retainer. 100-01164 9/16" Wrench 9-1/4 173-01001...

  • Page 28: Maintaining Your Appliance

    Firebox Parts ID # Description Floor and Side Firebrick Removal & Replacement Do not pry firebrick - they chip and crack easily. Maintaining Your Appliance Part # ID # Description Part #...
  • Page 29 Air Tube Collar Air Tube Remove the left pin on the air tube collar Roll Pin Slide the air tube to the left, swing it down and remove from the firebox.

  • Page 31: Freestanding Installation

    UL 1482, 737 AND 907. (520-NT) PREVENT HOUSE FIRES - Install and use only in accordance with the Lopi Liberty (520-NT) owner’s manual. Contact your local building or fire officials about restrictions and installation inspection in your area. Refer to local building codes and the chimney manufacturer’s instructions for precautions required for passing a chimney through a combustible wall or ceil-...
  • Page 32 Standard Screwdriver Rotate this shaft 1/4 turn clockwise until the door unlatches. Swing the door retianer open. Remove and discard the shipping latch and nut. Shipping Latch Door Shell Door Retainer 9/16" Wrench Door Retainer The indent on the door retainer slides into the clip on the door shell (on both sides).
  • Page 33 Make sure the door retainer is centered on the door shell. You can gauge the alignment by looking at the gaps here. 1/8” Hex Wrench Once the door is aligned, tighten the two set screws on the bottom of the door shell to secure the door retainer.
  • Page 34 These rubber-tipped bolts are for leveling the stove. Make sure they contact the floor. Do not adjust with weight on the legs, the rubber tips may tear.

  • Page 35: Optional Equipment

    1/2" socket wrench. 22” When attached, the faceplate of the stove is 4 3/4” in front of the front edge of the pedestal. The cover plate is used to seal off room air.
  • Page 36 The two yellow wires attach to the thermodisk. Three holes for attaching the blower box to the back of the stove Slide the thermodisk assembly into the space between the stove and rear heat shield.
  • Page 37 Optional Equipment Outside Air Boot Installation (Part number 99200134) stove...

This manual is also suitable for:

Liberty

Table of Contents

Save PDF