Table of Contents
Advertisement
Quick Links
Assembly and Operating Instructions for
3 Burner Stainless Steel with Hood Gas Barbecue
Drawings are not to scale.
Specifications subject to change
without prior notice.
• For outdoor use only. Not for commercial use.
• Use only Propane regulator 37mbar .
• Read instructions before using the appliance. Failure to follow
instructions could result in death, serious bodily injury, and/or property
loss.
• Warning: accessible parts may be very hot. Keep young children away.
• Do not move the appliance during use.
• Turn off the gas supply at the gas bottle after use.
• Any modification of the appliance, misuse, or failure to follow the
instructions may be dangerous and will invalidate your warranty. This does not
affect your statutory rights.
• Retain these instructions for future reference.
WARNING
• Leak test your barbecue annually. Check the hose connections are tight and leak
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open barbecue lid or hood.
4. If odour continues, discontinue use and contact
your local dealer.
Check the box and make sure you have all the parts and fittings listed. If not, contact your local store or the
Helpline
Argos Distribution Limited
Avebury, 489-499 Avebury Boulevard
Saxon Gate West, Central Milton Keynes, MK9 2NW
www.argos.co.uk
THG3208
test them each time you reconnect the gas bottle.
0844-335-0229
who will be able to help you.
FOR YOUR SAFETY
1. Do not store or use petrol or other flammable
vapours or liquids in the vicinity of this or any
other appliance.
2. A gas bottle not connected for use shall not be
stored in the vicinity of this or any other
appliance.
0359
Advertisement
Table of Contents
Related Manuals for Argos THG3208
Summary of Contents for Argos THG3208
- Page 1 Argos Distribution Limited Avebury, 489-499 Avebury Boulevard Saxon Gate West, Central Milton Keynes, MK9 2NW www.argos.co.uk Assembly and Operating Instructions for 3 Burner Stainless Steel with Hood Gas Barbecue THG3208 Drawings are not to scale. Specifications subject to change 0359 without prior notice.
-
Page 2: Parts List
A. Parts List Quantities vary according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see the corresponding Hardware Reference Diagram for your barbecue model. CODE PART 3 Burner Stainless Steel with Hood Hood (Pre-assembled to Body) Hood Handle Grill... -
Page 3: Parts Diagram
B. Parts Diagram Quantities vary according to model purchased. Specifications subject to change without prior notice. For more details on hardware, please see ‘Hardware Reference Diagram’. Check the box and make sure you have all the parts and fittings listed. If not, contact your local store or the 0844-335-0229 Helpline who will be able to help you. - Page 4 C. Hardware Reference Diagram Specifications subject to change without prior notice. D11,D14 D9,D13 D10, D13, D14 D12, D13, D14 D10,D14 Tools Required (not supplied) • Cross Head Screwdriver • Adjustable Spanner Tools Required (supplied) • Hex Spanner for Hose Assembly Unit:mm Check the box and make sure you have all the parts and fittings listed.
- Page 5 D. Assembly TOOLS NEEDED FOR ASSEMBLY: Medium size flat blade or Philips/crosspoint screwdriver, adjustable spanner or metric spanner set Please lay out all nuts and bolts and check lengths before assembling. Whilst every care is taken in the manufacture of this product, care must be taken during assembly in case sharp edges are present.
- Page 6 Attach the right leg assembly to the Front Panel (C11) using the M6x40 Bolts (D9) and Ø6 Washers (D13) as shown. Attach the left leg assembly to the Front Panel (C11) using the M6x40 Bolts (D9) and Ø6 Washers (D13) as shown. Check the box and make sure you have all the parts and fittings listed.
- Page 7 Feed the M6x45 Bolts (D10) through the Washers (D13), Rear Support (C8) and rear legs, secure with M6 Nuts (D14) as shown. Unscrew the Locknuts (D2) from both end of Axle (C16) to get Axle Washers (D1). Thread the axle through left legs Assembly, place a axle washer on each end of the axle, fit the Wheels (C17) onto the axle, and secure with locknuts.
- Page 8 Attach the Side Burner Rear/Front Support (C3,C4) to the Side Burner (C1) using M6x45 Bolt (D10) as shown. Connect the Side Burner assembly onto the left leg assembly using M6x55 Bolts (D12) and Washers (D13) and M6 Nuts (D14). Connect the side burner rear support onto the left back leg using a M6x45 Bolt (D10) and Washer (D13) and M6 Nut (D14).
- Page 9 Connect the Side Shelf Supports (C6) onto the Side Shelf (C5) using Side Shelf Short Pins (D4) and Spring Clips (D3) as shown. Connect the side shelf assembly onto the Right leg assembly using Side Shelf Long Pin (C18) and Spring Clips (D3) as shown. Check the box and make sure you have all the parts and fittings listed.
- Page 10 Feed the M6x45 Bolts (D10) through the Washers (D13), the body, left/right leg and secure with M6 Nuts (D14). Insert electrode ignition wire through the hole in the left Unscrew a M6 Nut from either M6x55 Bolt. sidewall of control panel and connect it onto the middle of Connect protective electric wire to left leg ignition pushbutton as shown.
- Page 11 Feed Grease Cup Holder (B5) through rear body hole and place the Grease Cup (B6) into the grease cup holder. Lay Flame Tamers (A5), Cooking Grill (A3), Fat Free Griddle (A4) into body as shown. Note: Place the flame tamers into barbecue body.
- Page 12 Install the Warming Rack (A6) into barbecue hood/body as shown. Place the Grid (C2) onto the side burner. IMPORTANT: Snip the line which hang hex spanner on the Hose / Regulator Assembly (B7) to get the spanner. IMPORTANT:Carefully screw the brass hex hose fitting onto the brass threaded gas inlet assembly on the side burner.
- Page 13 Attach the Left/Right Panel (C9,C10) to control panel using ST4.0x10 Screws (D5) as shown. ASSEMBLY IS NOW COMPLETED. PROCEED TO THE NEXT PAGE FOR INSTRUCTIONS ON OPERATION AND MAINTENANCE. Important- Please ensure the gas hose is free of kinks, twists and from its transit position. IMPORTANT - LEAK TESTING BEFORE USE, FAILURE TO CHECK AND PERFORM THE LEAK TEST COULD CAUSE SERIOUS INJURY, AND DAMAGE THE BARBECUE.
-
Page 14: Installation
E. Important Information directly under the barbecue. Gas bottles should never be stored or used laid on their side. Never Please read these instructions carefully before store gas bottles indoors. assembly and use. For optimal performance, we suggest the following: Retain these instructions for future reference. -
Page 15: Operation
G4. Fixing the Regulator to the Gas Bottle below. • Confirm all barbecue control knobs are in the off After ignition, the burner should be burned at position. Connect the regulator to the gas bottle the high position for 3-5 minutes in order to according to your regulator and bottle dealer’s preheat the barbecue. -
Page 16: Care And Maintenance
be used in exactly the same way as a griddle in the • Never handle hot parts with unprotected hands. kitchen, for searing steaks, cooking eggs, etc. Alternatively, it can be used for heating pans or In order to extend the life and maintain the condition keeping food warm. -
Page 17: Technical Specifications
holes. If the barbecue is to be stored indoors, the gas J. Technical Specifications bottle must be disconnected and left outside. The gas bottle should always be stored outside, in a dry, well- Heat Injector Model Burners ventilated area, away from any sources of heat or Approval Input Size... -
Page 18: Troubleshooting
K. Troubleshooting Problem Possible Cause Solution Burners will not light using LP gas bottle is empty Replace with full bottle the ignition system Faulty regulator Have regulator checked or replace Obstructions in burners Clean burners Obstructions in gas jets or gas hose Clean jets and gas hose Electrode wire is loose or disconnected Reconnect wire...
Need help?
Do you have a question about the THG3208 and is the answer not in the manual?
Questions and answers