Samsung SR20H9050U User Manual
Powerbot
Hide thumbs
Also See for SR20H9050U:
- User manual (140 pages) ,
- User manual (28 pages) ,
- User manual (112 pages)
Related Manuals for Samsung SR20H9050U
Summary of Contents for Samsung SR20H9050U
- Page 1 SR20H9050U SR20H9030U POWERbot user manual ✻ Before operating this unit, please read the instructions carefully. english ✻ For indoor use only. imagine the possibilities Thank you for purchasing a Samsung product.
-
Page 2: Table Of Contents
Contents Safety information Installation Accessories / Installation note Charging Automatic charging / Recharging / Low battery (Lo) Installing the Virtual guard Part name of the Virtual guard / Inserting batteries Using POWERbot Turning the power on/off / Using Auto clean mode / Using the cleaning modes / Recharging Using the remote control Power/Recharging / Cleaning mode /... -
Page 3: Safety Information
Safety information Safety information Before operating the appliance, please read this manual thoroughly and retain it • for your reference. WARNING Because these following operating instructions cover various models, the • characteristics of your vacuum cleaner may differ slightly from those described in WARNING this manual. -
Page 4: Important Safety Instructions
Safety information important Safety inStrUCtionS When using an electrical appliance, basic precautions should be observed, including the following: reaD aLL inStrUCtionS Before USinG yoUr poWerbot. Unplug from outlet when not in use and before conducting maintenance. WarninG: to reduce the risk of fire, electric shock, or injury: GeneraL • Use only as described in this manual. - Page 5 poWerbot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on. • Do not put any objects into openings.
- Page 6 – There is a risk of fire or electric shock. alcohol, thinners etc. ▶ Please check with a Samsung Electronics ▶ The POWERbot is intended for household service center when exchanging batteries. use therefore do not use it in an attic, –...
- Page 7 Before use in use CaUtion CaUtion ▶ Insert the dustbin before using POWERbot. ▶ Using POWERbot on thick carpet may damage both POWERbot and the carpet. ▶ Open room doors before cleaning in order to have all rooms cleaned and install a –...
-
Page 8: Installation
installation power of the charger must be on at all times. Install it in a place without obstacles and danger of falling. Power lamp (Red) D C - IN D C - I N Connect the Connect the Connect the power plug to adapter jack to power cord to... - Page 9 accessories remote control Batteries (aaa type) User manual/Quick Spare filter guide Cleaning brush power cord adapter Virtual guard installation note Note ▶ Install charger in a place where the floor and wall are level. ▶ It is best to install the charger along the grain of wooden floors. ▶...
-
Page 10: Charging
Charging It takes approximately 160 minutes to • Rated input voltage of this product completely charge when charging for the is 100-240 V~. WARNING first time after purchase and can be used for approximately 60 minutes. Charging lamp during charging (green) Check the turn on the manually charge... -
Page 11: Battery (Lo
automatic charging When the battery indicator blinks during cleaning, poWerbot will return to the charger to charge itself automatically. recharging you may command poWerbot to recharge at the charger while it is in cleaning process. Low battery (Lo) manually charge poWerbot by placing it on the charger. -
Page 12: Installing The Virtual Guard
installing the Virtual guard infrared ray from the Virtual guard will restrict poWerbot from approaching certain area. The distance of virtual wall is 2.5 m at minimum and may differ depending on surroundings and movement status of POWERbot. Virtual guard press the power install the Virtual guard button to turn it on... -
Page 13: Part Name Of The Virtual Guard
part name of the Virtual guard power button poWerbot detection sensor power lamp Power on: Red lamp blinks Distance detection sensor Power off: Lamp is off (infrared ray sensor) Battery cover inserting batteries Batteries for Virtual guard must be purchased separately. Open the battery cover Insert the alkaline Insert the tip of the... -
Page 14: Using Powerbot
Using poWerbot you must turn on the emergency switch before using poWerbot. turning the power on/off • When POWERbot is not used for 30 minutes, power will turn off press the button for more than WARNING automatically. 3 seconds - You can turn on the power only by using the buttons on POWERbot. -
Page 15: Cleaning Mode
Selecting cleaning mode cleaning mode How to select Displayed icon press once Auto clean press twice Spot clean press 3 times Max clean press 4 times Manual clean ✻ ✻ Direction control can be done only by the remote control. ✻... -
Page 16: Using The Remote Control
Using the remote control 1 power/recharging [A type] [B type] Power Turn POWERbot's power on/off Select to recharge POWERbot at the charger while it Recharging is in cleaning process 2 Cleaning mode Auto clean Select to automatically clean the entire space once Spot clean Select to clean a localized area intensely Select to make POWERbot to clean until battery... -
Page 17: Point Cleaning
[A type] 4 Direction control [A type] [B type] Select to move forward Select to turn left Select to turn right ✻ ✻ Moving backward is not available 5 point cleaning - Only available in A type remote controll ✻ ✻ N/A Refer to you can use the remote control to point and clean page 19... -
Page 18: Name Of Each Part
name of each part 1. Display panel 2. Dustbin holder 3. Remote control signal receiver 4. Virtual guard sensor 5. Obstacle sensor 6. Dustbin 7. Camera 8. Dustbin handle 9. Bumper sensor Bottom 1. Charge pins 2. Power brush 3. Power brush cover 4. -
Page 19: Setting Time/Schedule
Setting time/schedule B type remote control's buttons works in same manner as a type remote control. Setting the time You must set the current time before using the One-time/daily schedule. Start setting Select "Hour" Select "Minute" Setting complete Select "AM/PM" Skip to previous, next setting Setting the schedule Setting/cancelling the schedule can only be done while POWERbot is docked on the charger. -
Page 20: Cleaning And Maintaining
Cleaning and maintaining you must turn off the emergency switch before cleaning poWerbot. Cleaning the dustbin Clean the dustbin when filter inspection indicator ( ) turns on or if there's too much dust in the dustbin. Remove the dustbin Remove the dustbin Remove dust in the cover dustbin and cyclone... -
Page 21: Cleaning The Driving Wheel
Cleaning the power brush Remove the dustbin Remove the Power Remove the Power brush cover brush Clean the Power brush Reassemble the Power Reassemble the Power brush brush cover Cleaning the Driving wheel Put a soft cloth on the floor and place Use a blunt rod or tweezers to remove the POWERbot upside-down. -
Page 22: Notes And Cautions
notes and cautions ▶ The POWERbot cannot vacuum clumps of Charging dirt, so some may remain on the floor after cleaning. Note – Please use another cleaning tool to clean them ▶ If the battery overheats during charging, it regularly. may take longer to charge. - Page 23 > Charger model name before purchasing. ▶ When controlling POWERbot with the remote ▶ This battery is exclusive for Samsung control, POWERbot may cross the invisible Electronics POWERbot; do not use it for any barrier set by the Virtual guard and enter the other product.
-
Page 24: Error Codes
error codes Below error codes Turn off the Error code will appear on the emergency switch disappear when display panel and check the below you turn on the instructions and take emergency switch appropriate action error codes checklist foreign matter caught in the power brush. ▶Turn off the emergency switch and remove the foreign matter from the Power brush. -
Page 25: Troubleshooting
troubleshooting Symptom checklist ▶Check if the emergency switch is on. ▶Check if all the icons are displayed on display panel. the PoWeRbot is not ▶Check if the battery of POWERbot is depleted. working at all. - When "Lo" is displayed, carry POWERbot to the charger to charge it. ▶Replace the batteries (AAA type) when the remote controller is not working. -
Page 26: Open Source Announcement
It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM; a minimal charge will be required. The following URL http://opensource.samsung.com/opensource/VR9000H/seq/0 leads to the download page of the source code made available and open source license information as related to this product. This offer is valid to anyone in receipt of this information. -
Page 27: Specifications
Specifications classification Item Detail information Size 378 mm x 135 mm x 362 mm (Width x Height x Depth) Mechanical Weight 4.8 kg specifications (PoWeRbot) Sensor Ceiling shape recognition (Visionary mapping plus TM) Button type of POWERbot Touch type Power voltage 100-240 V~, 50 Hz/60 Hz Power Power consumption... - Page 28 If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Country Customer Care Center Web Site 0330 SAMSUNG (7267864) www.samsung.com SOUTH AFRICA 0860 7267864 (SAMSUNG) www.samsung.com AUSTRALIA 1300 362 603 www.samsung.com www.samsung.com/hk...