Setting For External Synchronization [Gen Lock]; Setting Details For Connecting Pc [Pc2]; Setting For External Interface - Panasonic AG-HMX100P Operating Instructions Manual

Setting for External Synchronization [GEN LOCK]

When the SD reference signal is input to this unit to perform
external synchronization, it is necessary to connect a
signal generator to the G/L (external synch reference input)
connectors. These two G/L connectors are in the loop-
through state, and automatically terminated when loop-
through is disabled.
This unit is also equipped with the ADV-REF (advanced
reference output) connector to output the reference signal
with the vertical phase advanced for the input source. This
reference signal can be used to minimize the delay of the
output signal caused by the system.
 NOTE
When the reference signal is connected or disconnected,
output images are distorted or sound is muted for several
seconds.

Setting Details for Connecting PC [PC2]

When videos created on PC are input to the DVI-I IN
connector of this unit, if the analog signal is input, it is
necessary to make detailed settings in the [PC2] submenu
of the [SETUP] menu.
Rotary 1 Rotary 2 Rotary 3
PC2 H POSI V POSI
30
0-60 0-20
0-300*
1
* When [PC1] is [1080/50] or [1080/60]
1
* When [PC1] is [XGA]
2
* When [PC1] is [WXGA]
3
* When [PC1] is [SXGA]
4

Setting for External Interface

This unit is equipped with the external interfaces as
described below to allow operating this unit from an
external controller or PC as well as operating a projector
from this unit.
To perform the remote operation, select [RS-232C] or [PJ]
(Projector) from the [RS-232C] submenu of the [SETUP]
menu ( page 29) and press the PROJECTOR/REMOTE
button to turn on to activate RS-232C control.
RS-232C connector
Enables to control all functions except for AUX input and
output. When using a conversion cable with 9-pin and 25-pin
plugs, connect the cable as shown below.
28
Rotary 4 Rotary 5
PHASE CLOCK
10 16 1000
0-31 1200-1500*
2
1500-1800*
3
1500-1800*
4
The [GEN LOCK] submenu of the [SETUP] menu is used to
make the settings for external synchronization.
Rotary 1 Rotary 2 Rotary 3
GEN. H PHASE
1000
LOCK
0-2000
To adjust the output phase of video, set [H PHASE]
(horizontal phase) using the rotary 2 control. Set [H PHASE]
(horizontal phase) using the rotary 2 control. The factory
default setting is 1000.
Set [H POSI] (horizontal position) using the rotary 2 control.
Set [V POSI] (vertical position) using the rotary 3 control.
Set [PHASE] using the rotary 4 control.
Set [CLOCK] using the rotary 5 control.
(Only an even number can be selected.)
 NOTE
The [PC2] parameters cannot be set in the following cases.
• [DIGITAL] is selected in [PC1]: No parameter can be set.
• [ANALOG] is selected in [PC1] and [FORMAT] is set to
1080/50P or 1080/60P: [CLOCK] cannot be set.
RS-232C
25-pin
2 TXD
3 RXD
4 RTS
5 CTS
6 DSR
7 SIG.G
20 DTR
• Under RS-232C control, the operation is executed three
frames after reception of the applicable command.
• When a transition pattern is selected, set the transition
time to 2 frames or more. If it is set to less than 2 frames,
frame accuracy is not certified.
Rotary 4 Rotary 5
AG-HMX100P/HMX100E
9-pin
1 SPARE
2 RXD
3 TXD
4 DTR
5 SIG.G
6 DSR
9 SPARE
[DCE connection]