Centurion D5-EVO Configuration Manual
  1. Manuals
  2. Brands
  3. Centurion Manuals
  4. Gate Opener
  5. D5-EVO REPAIR
  6. Configuration manual

Centurion D5-EVO Configuration Manual

Hide thumbs Also See for D5-EVO:

Advertisement

Table of Contents

See also: Programming Manual , User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D5-EVO and is the answer not in the manual?

Questions and answers

Dirk
April 19, 2025

how to set the speed of gate open gate close d5 evo

0

Related Manuals for Centurion D5-EVO

Summary of Contents for Centurion D5-EVO

  • Page 2: Comissioning The System

    Features of the full installation manual available on www.centsys.co.za. When setting up the D5-Evo and D10 system via the LCD display, all the steps that have to be followed are clearly provided via the display. It is only necessary to note the following:...

  • Page 3: Manu Navigation Map

    The schedule of Factory Defaults are detailed in the full installation manual, available for download on www.centsys.co.za Icon Menu Sub-menu 1.1. Setup wizard Setting limits Safety 2.1.1. Opening collision force 2.1. Collision force 2.1.2. Closing collision force 2.2. Collision count 2.3.
  • Page 4 Icon Menu Sub-menu Infrared beams 6.1. PIRAC control 6.1.1. PIRAC status 6.1.2. Stop on open 6.1.2.1. Stop on open status 6.1.2.2. Stopping distance 6.2. IR beam test 6.2.1. On/Off 6.2.2. Test beam selection (IRBC; IRBO; IRBC and IRBO) 6.3. IRBO=IRBC on closing 6.4.
  • Page 5 Icon Menu Sub-menu 10. General settings 10.1.Operating standard (ZA; CE; UL325) 10.2.Reset options 10.2.1. Factory defaults 10.2.2. Delete all remotes 10.2.3. Delete all Time-periods and exclusions 10.2.4. Reset all 10.3.Diagnostic screen on/off 10.4.Test button disabled/enabled 10.5.Backup EEPROM 10.6.Restore EEPROM 11. Remote controls Press button of valid transmitter (if menu locked)

  • Page 6: Diagnostic Leds

    4. Diagnostic LEDs The D5-Evo and D10 controllers have a series of diagnostic LEDs which indicate the state of the inputs. Normally-open inputs are indicated by a red LED, and normally-closed inputs by a green LED. An illuminated red LED indicates that the signal is present (e.g.
  • Page 7 LED indication LED indication Gate status Three flashes every two seconds Battery voltage is low Four flashes every two seconds Multiple collisions have occurred The LCD display shows useful information regarding the status of the system. 1. Battery icon Indicates the state of charge of the battery. Four solid bars = full capacity Two solid bars = 50% capacity No solid bars, with the icon flashing = battery empty...

  • Page 8: Buzzer Feedback

    A warning buzzer will sound (where applicable) as per the table below: Gate User can Priority Number of beeps Fault type continues Inhibitor name correct to operate error Break-in alarm Continuous tone for 30 seconds Alarm Ambush alarm Continuous tone until IRBs are cleared Alarm Multiple collision Periodic until condition is cleared by user (500/500ms)

  • Page 9: Electrical Setup

    Always check that the circuit breaker in the electrical panel is in the OFF position, and that all high voltage circuits (more than 42.4V) are completely isolated from the mains supply before doing any work. Ensure that all low voltage systems (less than 42.4V) are suitably protected from damage, by disconnecting all sources of power such as chargers and batteries before doing any work.
  • Page 10 Motor Motor output – connects to the thick blue motor wire Motor Motor output – connects to the thick black motor wire 12V/24 + Positive battery connection. Battery terminal normally indicated as + or red (right hand battery) 12V/24 - Negative battery connection.

This manual is also suitable for:

D10

Table of Contents

Save PDF