Table of Contents
Advertisement
Sectional and Tilting Door Opener
Installation Instructions and User Guide
SDO800
WARNING
Please read the manual carefully before installation and use. The
installation of your new door opener must be carried out by a technically
qualified or licensed person. Attempting to install or repair the door opener
without suitable technical qualification may result in severe personal injury,
death and / or property damage.
Advertisement
Table of Contents
Related Manuals for Napoleon SDO800
Summary of Contents for Napoleon SDO800
- Page 1 Sectional and Tilting Door Opener Installation Instructions and User Guide SDO800 WARNING Please read the manual carefully before installation and use. The installation of your new door opener must be carried out by a technically qualified or licensed person. Attempting to install or repair the door opener without suitable technical qualification may result in severe personal injury, death and / or property damage.
-
Page 2: Table Of Contents
CONTENTS Important Safety Recommendations..…………………………….………………………….….1-2 Basic function introduction………..……………………………………………….……………...2 Special function introduction………….…………………………………………………………..2 Installation (aluminum track)………………………………………….…………………………..3-4 Installation (steel track)………………………………………….…………………………….…..5-6 Installation recommendations……………………………………………………………………..7 Basic function setting and applying……………………………………………………………..8-9 Special function introduction and application………………………………………….……….10 Aluminum & steel track accessories list………………………………………………….……...11 Manual disengagement……………………………………………………………………………12 Maintenance………………………………………………………………………………………...13 Final note….………………………………………………………………………………………...13 Important information for the user………………………………………………………………...13... -
Page 3: Important Safety Recommendations
Important safety recommendations FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN SERIOUS PERSONAL INJURY, DEATH AND / OR PROPERTY DAMAGE. 1. PLEASE READ CAREFULLY AND ADHERE TO ALL SAFETY AND INSTALLATION RECOMMENDATIONS. 2. The opener is designed and manufactured to meet local regulations. The installer must be familiar with local regulations required in respect of the installation of the opener. -
Page 4: Basic Function Introduction
Frequently examine the installation, in particular check cables, springs and mountings for signs of wear, damage or imbalance. Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced door may cause injury. Each month check that the drive reverses when the door contacts a 50 mm high object placed on the floor. -
Page 5: Installation (Aluminum Track)
Referring to Fig. 2 for recommended installation 1) Aluminum track 5) Inside panel 2) 24V DC flashing light (optional extra) 6) Power socket 3) Push button 7) Door opener 4) Photo beam (RX/TX Type) CHAIN SHUTTLE ASSEMBLY As for the ease of the chain, it is delivered with the chain and chain shuttle already assembled in the track. - Page 6 Before attaching the motor brackets (E) (FIG 4) screw an inverted nut (6mm) (D) on each stud then position the brackets (E) on the studs and secure them in-place using a second 6mm-nut and then lock the brackets to the rail by tightening the inverted lock nuts (D).Fix the opener to the doorframe or to the ceiling with the correct fixing (Fig.5), maintaining a minimum gap of 30mm from...
-
Page 7: Installation (Steel Track)
Installation (steel track) Fig. 1 Fig. 2... - Page 8 1. Fixing the track bracket. Fixing the track bracket to the wall 2cm-15cm over the shaft or intermediate bracket (depend on the actual installation space). 2. Fixing the steel track to the bracket with cotter pin A. (Fig. 1) 3. Fixing garage door opener to the track by U hanging bracket A. It‟s enough for 2 Nm fastening force.
-
Page 9: Installation Recommendations
Installation recommendations Remember there are specific standards that have to be strictly followed regarding the safety rules of electrical installations and automatic gates and doors. As for the legal requirements and standards that must be adhered to, please take notice of the following points to ensure maximum safety and reliability of your installation. -
Page 10: Basic Function Setting And Applying
Basic function setting and applying 1. Itinerary setting Opening & closing force self-learning Press „SET‟ button and hold on until the LED displays figure „1‟, then adjust the up limit by pressing „LIM-1‟ button. Fine-tuning „LIM-1‟(up) or „LIM-2‟(down) button to determine the final up limit position then press „set‟ button the display turn into „2‟... - Page 11 3. Safety reverse force adjustment Press „SET‟ button and hold on until the LED displays „3‟. It‟s under force adjustment mode. Press „LIM-1‟ button to increase the force and „LIM-2‟ button to decrease the force. The maximum force is 9 and the minimum is 1.
-
Page 12: Special Function Introduction And Application
Fig. 1 Fig. 2 Special function introduction and application The following functions are made to order in accordance with the special needs of customers: 1．The O/S/C button function Add an O/S/C button to open or close the door. 2．Auto safety reverse function This special function is for safety consideration. -
Page 13: Aluminum & Steel Track Accessories List
Aluminum track accessories list Name Amount Clutch Components ×1 Hanging bracket ×1 Motor bracket ×2 φ6×90 axis pin ×1 φ8×55 carriage bolt ×2 Bracket for door panel ×1 Bracket for track ×1 Clutch cord ×1 Cord pendant ×1 φ1.8×38 Cotter pin ×2 φ6×14 bolt ×8... -
Page 14: Manual Disengagement
Manual disengagement The opener is equipped with a manual release cord to disengage shuttle and move door by hand while holding the handle down (Fig 12). Pull on the handle to disengage the shuttle. To re-engage the door simply run opener in automatic mode or move door by hand until the trolley engages in the chain shuttle. -
Page 15: Final Note
Technical specifications Power Input: 140W (800N) 220 - 240 V AC 50 Hz or 110 -120 V AC 60 Hz (subject to customer‟s area) Motor: 800N: 50W Light time: 3 minutes Working temperature: -20° ~ 40° C Relative Humidity: <90% Open and close force: 800N Reception frequency:... - Page 16 73-75 Magnesium Drive, Crestmead Qld 4132 Ph: (07) 3803 7600 Fax: (07) 3803 7611 Email: enquiries@napoleongd.com.au Web: www.napoleongd.com.au...
Need help?
Do you have a question about the SDO800 and is the answer not in the manual?
Questions and answers